DOI QR코드

DOI QR Code

An experimental investigation on effect of elevated temperatures on bond strength between externally bonded CFRP and concrete

  • 투고 : 2018.04.14
  • 심사 : 2019.08.21
  • 발행 : 2019.09.10

초록

The bond strength between composite laminates and concrete is a key factor that controls the behavior of concrete members strengthened with fiber reinforced polymer (FRP) sheets, which can be affected by several parameters such as thermal stresses and surface preparation. This article presents the result of an experimental study on the bond strength between FRP sheets and concrete at ambient temperature after specimens had been exposed to elevated temperatures of up to $200^{\circ}C$. For this purpose, 30 specimens of plain concrete with dimensions of $150{\times}150{\times}350mm$ were prepared. Three different conventional surface preparation methods (sandblasting, wire brushing and hole drilling) were considered and compared with a new efficient method (fiber implantation). Deformation field during each experiment was monitored using particle image velocimetry. The results showed that, the specimens which were prepared by conventional surface preparation methods, preserved their bond integrity when exposed to temperature below glass transition temperature of epoxy resin (about $60^{\circ}C$). Beyond this temperature, the bond strength and stiffness decreased significantly (about 50%) in comparison with control specimens. However, the specimens prepared by the proposed method displayed higher bond strengths of up to 32% and 90% at $25^{\circ}C$ and $200^{\circ}C$, respectively.

키워드

과제정보

연구 과제 주관 기관 : Ferdowsi University of Mashhad

참고문헌

  1. Adrian, R.J. (1991), "Particle-imaging techniques for experimental fluid mechanics", Annual Rev. Fluid Mech., 23(1), 261-304. https://doi.org/10.1146/annurev.fl.23.010191.001401
  2. Ali-Ahmad, M., Subramaniam, K. and Ghosn, M. (2006), "Experimental investigation and fracture analysis of debonding between concrete and FRP sheets", J. Eng. Mech., 132(9), 914-923. https://doi.org/10.1061/(ASCE)0733-9399(2006)132:9(914)
  3. Al-Salloum, Y.A., Elsanadedy, H.M. and Abadel, A.A. (2011), "Behavior of FRP-confined concrete after high temperature exposure", Constr. Build. Mater., 25(2), 838-850. https://doi.org/10.1016/j.conbuildmat.2010.06.103
  4. ASTM D3039M-00 (2000), Standard test method for tensile properties of polymer matrix composite materials.
  5. Barros, J.A.O. and Fortes, A.S. (2005), "Flexural strengthening of concrete beams with CFRP laminates bonded into slits", Cement Concrete Compos., 27(4), 471-480. https://doi.org/10.1016/j.cemconcomp.2004.07.004
  6. Blontrock, H. (2003), "Analysis and modeling of the fire resistance of concrete elements with externally bonded FRP reinforcement", Ph.D. Thesis; Ghent University, Ghent, Belgium.
  7. Burke, P.J., Bisby, L.A. and Green, M.F. (2013), "Effects of elevated temperature on near surface mounted and externally bonded FRP strengthening systems for concrete", Cement Concrete Compos., 35(1), 190-199. https://doi.org/10.1016/j.cemconcomp.2012.10.003
  8. Carolin, A., Nordin, H. and Taljsten, B. (2001), "Concrete beams strengthened with near surface mounted reinforcement of CFRP", Proceedings of International Conference on FRP Composites in Civil Engineering, Amsterdam, Netherlands.
  9. Chen, J. and Teng, J. (2001), "Anchorage strength models for FRP and steel plates bonded to concrete", J. Struct. Eng., 127(7), 784-791. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:7(784)
  10. Cheng, H.-L., Sotelino, E.D. and Chen, W.-F. (2002), "Strength estimation for FRP wrapped reinforced concrete columns", Steel Compos. Struct., Int. J., 2(1), 1-20. https://doi.org/10.12989/scs.2002.2.1.001
  11. De Lorenzis, L. (2004), "Anchorage length of near surface mounted FRP bars for concrete strengthening - analytical modelling", ACI Struct. J., 101(3), 375-386.
  12. Firmo, J.P., Correia, J.R. and Bisby, L.A. (2015a), "Fire behaviour of FRP-strengthened reinforced concrete structural elements: a state-of-the-art review", Compos. Part B: Eng., 80, 198-216. https://doi.org/10.1016/j.compositesb.2015.05.045
  13. Firmo, J.P., Pitta, D., Correia, J.R., Tiago, C. and Arruda, M.R.T. (2015b), "Experimental characterization of the bond between externally bonded reinforcement (EBR) CFRP strips and concrete at elevated temperatures", Cement Concrete Compos., 60, 44-54. https://doi.org/10.1016/j.cemconcomp.2015.02.008
  14. Grace, N.F., Sayed, G.A., Soliman, A.K. and Saleh, K.R. (1999), "Strengthening reinforced concrete beams using fiber reinforced polymer (FRP) laminates", ACI Struct. J., 96(5), 865-874.
  15. Hadji, L., Daouadji, T.H., Meziane, M. and Bedia, E. (2016), "Analyze of the interfacial stress in reinforced concrete beams strengthened with externally bonded CFRP plate", Steel Compos. Struct., Int. J., 20(2), 413-429. https://doi.org/10.12989/scs.2016.20.2.413
  16. Hajialilue-Bonab, M., Azarnya-Shahgoli, H. and Sojoudi, Y. (2011), "Soil deformation pattern around laterally loaded piles", Int. J. Phys. Model. Geotech., 11(3), 116-125. https://doi.org/10.1680/ijpmg.2011.11.3.116
  17. Hajihashemi, A., Mostofinejad, D. and Azhari, M. (2011), "Investigation of RC beams strengthened with prestressed NSM CFRP laminates", J. Compos. Constr., ASCE, 15(6), 887-895. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000225
  18. Hosseini, A. and Mostofinejad, D. (2013), "Experimental investigation into bond behavior of CFRP sheets attached to concrete using EBR and EBROG techniques", Compos. Part B: Eng., 51, 130-139. https://doi.org/10.1016/j.compositesb.2013.03.003
  19. Kim, Y.J., Hmidan, A., Choi, K. and Yazdani, S. (2012), "Fracture characteristics of notched concrete beams shear-strengthened with CFRP sheets subjected to high temperature", ACI-Special Publication (SP-286): A Fracture Approach for FRP-concrete.
  20. Klamer, E.L. (2009), "Influence of temperature on concrete beams strengthened in flexure with CFRP", Ph.D. Thesis; Civil Engineering, Eindhoven University of Technology, Eindhoven, Netherlands.
  21. Klamer, E.L., Hordijk, D.A. and Janssen, H.J. (2005), "The influence of temperature on the debonding of externally bonded CFRP", Proceedings of 7th International Symposium on Fiber-Reinforced (FRP) Polymer Reinforcement for Concrete Structures, New Orleans, LA, USA, November, pp. 1551-1570.
  22. Klamer, E.L., Hordijk, D.A. and de Boer, A. (2007), "FE-analyses to study the effect of temperature on debonding of externally bonded CFRP", Proceedings of 8th International Symposium on Fiber Reinforced Polymer Reinforcement for Concrete Structures (FRPRCS-8), Patras, Greece, July.
  23. Leone, M., Matthys, S. and Aiello, M.A. (2009), "Effect of elevated service temperature on bond between FRP EBR systems and concrete", Compos. Part B Eng., 40(1), 85-93. https://doi.org/10.1016/j.compositesb.2008.06.004
  24. Malek, A.M., Saadatmanesh, H. and Ehsani, M.R. (1998), "Prediction of failure load of R/C beams strengthened with FRP plate due to stress concentration at the plate end", ACI Struct. J., 95, 142-152.
  25. Mazzotti, C., Savoia, M. and Ferracuti, B. (2008), "An experimental study on delamination of FRP plates bonded to concrete", Constr. Build. Mater., 22(7), 1409-1421. https://doi.org/10.1016/j.conbuildmat.2007.04.009
  26. Mostofinejad, D. and Hajrasouliha, M.J. (2010), "Experimental study on grooving detail for elimination of debonding of FRP sheets from concrete surface", Proceedings of the 5th International Conference on FRP Composites in Civil Engineering, Beijing, China, pp. 545-547.
  27. Namrou, A.R. (2013), "An experimental investigation into the behavior of concrete elements rerofitted with NSM composite strips at elevated temperatures", M.Sc. Thesis; University of Colorado at Denver, Denver, CO, USA.
  28. Nordin, H. and Taljsten, B. (2006), "Concrete beams strengthened with prestressed near surface mounted CFRP", J. Compos. Constr., ASCE, 10(1), 60-68. ttps://doi.org/10.1061/(ASCE)1090-0268(2006)10:1(60)
  29. Slominski, C., Niedostatkiewicz, M. and Tejchman, J. (2007), "Application of particle image velocimetry (PIV) for deformation measurement during granular silo flow", Powder Technol., 173(1), 1-18. https://doi.org/10.1016/j.powtec.2006.11.018
  30. Spadea, G., Bencardino, F. and Swamy, R.N. (1998) "Structural behaviour of composite RC beams with externally bonded CFRP", J. Compos. Constr., ASCE, 2(3), 132-137. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:3(132)
  31. White, D. and Take, W. (2002), "GeoPIV: Particle Image Velocimetry (PIV) software for use in geotechnical testing".
  32. White, D., Take, W. and Bolton, M. (2003), "Soil deformation measurement using particle image velocimetry (PIV) and photogrammetry", Geotechnique, 53(7), 619-631. https://doi.org/10.1680/geot.2003.53.7.619
  33. Wu, Z., Iwashita, K., Yagashiro, S., Ishikawa, T. and Hamaguchi, Y. (2005), "Temperature effect on bonding and debonding behavior between FRP sheets and concrete", J. Soc. Mater. Sci., 54(5), 474-480. https://doi.org/10.2472/jsms.54.474
  34. Xin, H., Liu, Y. and Du, A. (2015), "Thermal analysis on composite girder with hybrid GFRP-concrete deck", Steel Compos. Struct., Int. J., 19(5), 1221-1236. https://doi.org/10.12989/scs.2015.19.5.1221
  35. Yao, J., Teng, J. and Chen, J. (2005), "Experimental study on FRPto-concrete bonded joints", Compos. Part B: Eng., 36(2), 99-113. https://doi.org/10.1016/j.compositesb.2004.06.001

피인용 문헌

  1. Stress-strain model of weak PVC-FRP confined concrete column and strong RC ring beam joint under eccentric compression vol.35, pp.1, 2020, https://doi.org/10.12989/scs.2020.35.1.013