DOI QR코드

DOI QR Code

Characterization of the main component of equal width welded I-beam-to-RHS-column connections

  • Lopez-Colina, Carlos (Department of Construction and Manufacturing Engineering, University of Oviedo) ;
  • Serrano, Miguel A. (Department of Construction and Manufacturing Engineering, University of Oviedo) ;
  • Lozano, Miguel (Department of Construction and Manufacturing Engineering, University of Oviedo) ;
  • Gayarre, Fernando L. (Department of Construction and Manufacturing Engineering, University of Oviedo) ;
  • Suarez, Jesus M. (Department of Construction and Manufacturing Engineering, University of Oviedo) ;
  • Wilkinson, Tim (School of Civil Engineering, University of Sydney)
  • Received : 2018.11.15
  • Accepted : 2019.07.23
  • Published : 2019.08.10

Abstract

The present paper tries to contribute fill the gap of application of the component method to tubular connections. For this purpose, one typical joint configuration in which just one component can be considered as active has been studied. These joints were selected as symmetrically loaded welded connections in which the beam width was the same as the column width. This focused the study on the component 'side walls of rectangular hollow sections (RHS) in tension/compression'. It should be one of the main components to be considered in welded unstiffened joints between I beams and RHS columns. Many experimental tests on double-sided I-beam-to-RHS-column joint with a width ratio 1 have been carried out by the authors and a finite element (FE) model was validated with their results. Then, some different analytical approaches for the component stiffness and strength have been assessed. Finally, the stiffness proposals have been compared with some FE simulations on I-beam-to-RHS-column joints. This work finally proposes the most adequate equations that were found for the stiffness and strength characterization of the component 'side walls of RHS in tension/compression' to be applied in a further unified global proposal for the application of the component method to RHS.

Keywords

References

  1. ANSYS, Inc. (2016), ANSYS 17.0 Release notes, ANSYS, Canonsburg, PA, USA.
  2. Aribert, J.M., Lachal, A. and Moheissen, M. (1990), "Modelling and experimental investigation of plastic resistance and local buckling of H or I steel sections submitted to concentrated or partially distributed loading", Contact Loading and Local Effects in Thin-walled Plated and Shell Structures. IUTAM Symposium, Prague, Czech Republic, September.
  3. Aribert, J.M., Younes, I. and Lachal, A. (2002), "Low-cycle fatigue of steel connections subjected to a transverse concentrated load: experimental investigation and practical formulation", Proceedings of 3rd European Conference on Steel and Composite Structures, Coimbra, Portugal, September.
  4. Barnett, T.C., Tizani, W. and Nethercot, D.A. (2001), "The practice of blind bolting connections to structural hollow sections : A review", Steel Compos. Struct., Int. J., 1(1), 1-16. https://doi.org/10.12989/scs.2001.1.1.001
  5. Chen, S., Pan, J., Yuan, H., Xie, Z., Wang, Z. and Dong, X. (2017), "Mechanical behavior investigation of steel connections using a modified component method", Steel Compos. Struct., Int. J., 25(1), 117-126. https://doi.org/10.12989/scs.2017.25.1.117
  6. Eslami, M. and Namba, H. (2016), "Rotation capacity of composite beam connected to RHS column, experimental test results", Steel Compos. Struct., Int. J., 22(1), 141-159. https://doi.org/10.12989/scs.2016.22.1.141
  7. Eurocode (2005a), Design of Steel Structures, Part 1-8: Design of Joints, European Committee for Standardization; Brussels, Belgium.
  8. Eurocode (2005b), Design of Steel Structures, Part 1-1: General Rules and Rules for Buildings, European Committee for Standardization; Brussels, Belgium.
  9. Eurocode (2006a), Design of Steel Structures, Part 1-5: Plated Structural Elements, European Committee for Standardization; Brussels, Belgium.
  10. Eurocode (2006b), Design of Steel Structures, Part 1-3: General Rules. Supplementary Rules for Cold-Formed members and Sheeting, European Committee for Standardization, Brussels, Belgium.
  11. Coelho, A.M.G., Simoes da Silva, L. and Bijlaard, F.S. (2006), "Ductility analysis of bolted extended end plate beam-tocolumn connections in the framework of the component method", Steel Compos. Struct., Int. J., 6(1), 33-53. https://doi.org/10.12989/scs.2006.6.1.033
  12. Hadianfar, M.A. and Rahnema, H. (2010), "Effects of RHS face deformation on the rigidity of beam-column connection", Steel Compos. Struct., Int. J., 10(6), 491-502. https://doi.org/10.12989/scs.2010.10.6.489
  13. Jaspart, J.P. and Weynand, K. (2015), "Design of hollow section joints using the component method", Proceedings of 15th International Symposium on Tubular Structures, Rio de Janeiro, Brazil, May.
  14. Kozlowski, A. (2016), "Component method model for predicting the moment resistance, stiffness and rotation capacity of minor axis composite seat and web site plate joints", Steel Compos. Struct., Int. J., 20(3), 469-486. https://doi.org/10.12989/scs.2016.20.3.469
  15. Kurobane, Y., Packer, J.A., Wardenier, J. and Yeomans, N. (2005), Design guide 9 for structural hollow section column connections, TU V-Verlag GmbH, Cologne, Germany.
  16. Leong, S.H., Sulong, N.H. and Jameel, M. (2016), "Bolted connections to tubular columns at ambient and elevated temperatures - a review", Steel Compos. Struct., Int. J., 21(2), 303-321. https://doi.org/10.12989/scs.2016.21.2.303
  17. Lopez-Colina, C., Serrano, M.A., Gayarre, F.L. and Suarez, F.J. (2010), "Resistance of the component 'lateral faces of RHS' at high temperature", Eng. Struct., 32(4), 1133-1139. https://doi.org/10.1016/j.engstruct.2009.12.039
  18. Lopez-Colina, C., Serrano, M.A., Gayarre, F.L. and del Coz, J.J. (2011), "Stiffness of the component 'lateral faces of RHS' at high temperature", J. Constr. Steel Res., 67(12), 1835-1842. https://doi.org/10.1016/j.jcsr.2011.05.006
  19. Lopez-Colina, C., Serrano, M.A., Gayarre, F.L. and Gonzalez, J. (2014), "The component 'lateral faces of RHS' under compression at ambient and high temperature", Int. J. Steel Struct., 14(1), 13-22. https://doi.org/10.1007/s13296-014-1002-8
  20. Lopez-Colina, C., Serrano, M.A., Lozano, M., Gayarre, F.L. and Suarez, J. (2017), "Simplified Models for the Material Characterization of Cold-Formed RHS", Materials, 10(9), 1043. https://doi.org/10.3390/ma10091043
  21. Lu, L.H. (1997), "The static strength of I-beam to rectangular hollow section column connections", Ph.D. Dissertation; Delft University of Technology, Delft, Netherlands.
  22. Lu, L.H., de Winkel, G.D., Yu, Y. and Wardenier, J. (1994), "Deformation limit for the ultimate strength of hollow section joints", Proceedings of 6th International Symposium on Tubular Structures, Melbourne, Australia, December.
  23. Lu, L.H., de Winkel, G.D., Yu, Y. and Wardenier, J. (1997), "Deformation limit for the ultimate strength of hollow section joints", Proceedings of 6th International Symposium on Tubular Structures, Melbourne, Australia, December.
  24. Pitrakkos, T. and Tizani, W. (2015), "A component method model for blind-bolts with headed anchors in tension". Steel Compos. Struct., Int. J., 6(5), 1305-1330. http://dx.doi.org/10.12989/scs.2015.18.5.1305
  25. Prabhavathy, A. and Knight, G.M. (2006), "Behaviour of coldformed steel concrete infilled RHS connections and frames", Steel Compos. Struct., Int. J., 6(1), 71-85. https://doi.org/10.12989/scs.2006.6.1.071
  26. Quin, Y., Chen, Z. and Rong, B. (2015), "Component-based mechanical models for concrete-filled RHS connections with Diaphragms under bending moment", Adv. Struct. Eng., 18(8), 1241-1256. https://doi.org/10.1260/1369-4332.18.8.1241
  27. Ramli Sulong, N.H., Elghazouli, A.Y., Izzuddin, B.A. and Ajit, N. (2010), "Modelling of beam-to-column connections at elevated temperature using the component method", Steel Compos. Struct., Int. J., 10(1), 23-43. https://doi.org/10.12989/scs.2010.10.1.023
  28. Serrano, M.A., Lopez-Colina, C., Gonzalez, J. and Gayarre, F.L. (2016), "A simplified simulation of welded I beam-to-RHS column joints", Int. J. Steel Struct., 16(4), 1095-1105. https://doi.org/10.1007/s13296-016-0028-5
  29. Van der Vegte, G.J., Wardenier, J. and Puthli, R.S. (2010), "FE analysis for welded hollow section joints and bolted joints", Proceedings of the Institution of Civil Engineers - Structures and Buildings, 163(6), 427-437. https://doi.org/10.1680/stbu.2010.163.6.427
  30. Wang, Y.C. and Park, A.Y. (2011), "Development of component stiffness equations for bolted connections to RHS columns", J. Constr. Steel Res., 70, 137-152. https://doi.org/10.1016/j.jcsr.2011.08.004
  31. Wardenier, J., Packer, J.A., Zhao, X.L. and van der Vegte, G.J. (2010), Hollow Sections in Structural Applications, (2nd Edition), CIDECT, Geneva, Switzerland.
  32. Weynand, K., Jaspart, J.P., Demonceau, J.F. and Zhang, L. (2015), "Component method for tubular joints", Draft Final Report No. 16F-3/15; Comite International pour le Developpement et l'Etude de la Construction Tubulaire, Liege, Belgium.
  33. Yu, Y. (1997), "The static strength of uniplanar and multiplanar connections in rectangular hollow sections", Ph.D. Dissertation; Delft University of Technology, Delft, Netherlands.

Cited by

  1. Further study on improvement on strain concentration in through-diaphragm connection vol.39, pp.2, 2019, https://doi.org/10.12989/scs.2021.39.2.135