Earthquakes and Structures

  • 제17권1호
  • /
  • Pages.75-89
  • /
  • 2019
  • /
  • 2092-7614(pISSN)
  • /
  • 2092-7622(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Seismic performance of RC frame having low strength concrete: Experimental and numerical studies

  • Rizwan, Muhammad (Earthquake Engineering Center, Department of Civil Engineering, UET Peshawar) ;
  • Ahmad, Naveed (Earthquake Engineering Center, Department of Civil Engineering, UET Peshawar) ;
  • Khan, Akhtar Naeem (Earthquake Engineering Center, Department of Civil Engineering, UET Peshawar)
  • 투고 : 2018.04.29
  • 심사 : 2019.05.17
  • 발행 : 2019.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

The paper presents experimental and numerical studies carried out on low-rise RC frames, typically found in developing countries. Shake table tests were conducted on 1:3 reduced scaled two-story RC frames that included a code conforming SMRF model and another non-compliant model. The later was similar to the code conforming model, except, it was prepared in concrete having strength 33% lower than the design specified, which is commonly found in the region. The models were tested on shake table, through multiple excitations, using acceleration time history of 1994 Northridge earthquake, which was linearly scaled for multi-levels excitations in order to study the structures' damage mechanism and measure the structural response. A representative numerical model was prepared in finite element based program SeismoStruct, simulating the observed local damage mechanisms (bar-slip and joint shear hinging), for seismic analysis of RC frames having weaker beam-column joints. A suite of spectrum compatible acceleration records was obtained from PEER for incremental dynamic analysis of considered RC frames. The seismic performance of considered RC frames was quantified in terms of seismic response parameters (seismic response modification, overstrength and displacement amplification factors), for critical comparison.

키워드

참고문헌

  1. ACI 318 (2005), Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute, Farmington Hills, MI, USA.
  2. Adom-Asamoah, M. and Banahene, J.O. (2016), "Nonlinear seismic analysis of a super 13-element reinforced concrete beam-column joint model", Earthq. Struct., 11(5), 905-924. https://doi.org/10.12989/eas.2016.11.5.905.
  3. Ahmad, N., Akbar, J., Rizwan, M., Alam, B., Khan, A.N. and Lateef, A. (2019b), "Haunch retrofitting technique for seismic upgrading deficient RC frames", Bull. Earthq. Eng., 17(7), 3895-3932. DOI: https://doi.org/10.1007/s10518-019-00638-9.
  4. Ahmad, N., Ali, Q. and Javed, M. (2019), "Force reduction factor R for shear dominated low-rise brick masonry structures", J. Numer. Meth. Civil Eng., 2(3), 14-29.
  5. Ahmad, N., Shahzad, A., Ali, Q., Rizwan, M. and Khan, A.N. (2018), "Seismic fragility functions for code compliant & noncompliant RC SMRF structures in Pakistan", Bull. Earthq. Eng., 16(10), 4675-4703. https://doi.org/10.1007/s10518-018-0377-x.
  6. Ahmad, N., Shahzad, A., Rizwan, M., Khan, A.N., Ali, S.M., Ashraf, M., Naseer, A., Ali, Q. and Alam, B. (2019a), "Seismic performance assessment of non-compliant SMRF reinforced concrete frame: shake table test study", J. Earthq. Eng., 23(3), 444-462. https://doi.org/10.1080/13632469.2017.1326426.
  7. Akbar, J., Ahmad, N. and Alam, B. (2018), "Seismic performance of RC frames retrofitted with haunch technique", Struct. Eng. Mech., 67(1), 1-8. https://doi.org/10.12989/sem.2018.67.1.001.
  8. Alath, S. and Kunnath, S.K. (1995), "Modeling inelastic shear deformations in RC beam-column joints", Engineering Mechanics Proceedings of the 10th Conference, University of Colorado at Boulder, Boulder, Colorado.
  9. Ali, Q., Naeem, A., Ashraf, M., Ahmed, A., Alam, B., Ahmad, N., Fahim, M., Rahman, S. and Umar, M. (2013), "Seismic performance of stone masonry buildings used in the Himalayan Belt", Earthq. Spectra, 29(4), 1159-1181. https://doi.org/10.1193/091711EQS228M.
  10. Ali, Q., Schacher, T., Ashraf, M., Alam, B., Naeem, A., Ahmad, N. and Umar, M., (2012), "In-plane behavior of Dhajji-Dewari structural system (wooden braced frame with masonry infill)", Earthq. Spectra, 28(3), 835-858. https://doi.org/10.1193/1.4000051.
  11. Arslan, M.H. and Korkmaz, H.H. (2007), "What is to be learned from damage and failure of reinforced concrete structures during recent earthquakes in Turkey?", Eng. Fail. Anal., 14(1), 1-22. https://doi.org/10.1016/j.engfailanal.2006.01.003.
  12. Ates, S., Kahya, V., Yurdakul, M. and Adanur, S. (2013), "Damages on reinforced concrete buildings due to consecutive earthquakes in Van", Soil Dyn. Earthq. Eng., 53, 109-118. https://doi.org/10.1016/j.soildyn.2013.06.006.
  13. Badrashi, Y.I., Ali, Q. and Ashraf, M. (2010), "Reinforced concrete buildings in Pakistan-Housing Report", Housing Report No. 159, Earthquake Engineering Research Institute, CA, USA.
  14. BCP-SP (2007), Building Code of Pakistan: Seismic Provisions- 2007, Ministry of Housing and Works, Islamabad, Pakistan.
  15. Biddah, A. and Ghobarah, A. (1999), "Modelling of shear deformation and bond slip in reinforced concrete joints", Struct. Eng. Mech., 7(4), 413-432. https://doi.org/10.12989/sem.1999.7.4.413.
  16. Calvi, G.M., Magenes, G. and Pampanin, S. (2002), "Relevance of beam-column joint damage and collapse in RC frame assessment", J. Earthq. Eng., 6(1), 75-100. https://doi.org/10.1080/13632460209350411
  17. Caprili, S., Mattei, F., Gigliotti, R. and Salvatore, W. (2018), "Modified cyclic steel law including bond-slip for analysis of RC structures with plain bars", Earthq. Struct., 14(3), 187-201. https://doi.org/10.12989/eas.2018.14.3.187.
  18. Celik, O.C. and Ellingwood, B.R. (2008), "Modelling beamcolumn joints in fragility assessment of gravity load designed reinforced concrete frames", J. Earthq. Eng., 12(3), 357-381. https://doi.org/10.1080/13632460701457215.
  19. Deierlein, G.G., Reinhorn, AM. and Willford, M.R. (2010), "Nonlinear structural analysis for seismic design", NEHRP Seismic Design Technical Brief No. 4, produced by the NEHRP Consultants Joint Venture, a partnership of the Applied Technology Council and the Consortium of Universities for Research in Earthquake Engineering, for the National Institute of Standards and Technology, Gaithersburg, MD, NIST GCR 10-917-5.
  20. Elnashai, A.S. and Di-Sarno, L. (2008), Fundamentals of Earthquake Engineering, A John Wiley & Sons, Ltd., West Sussex, UK.
  21. Erdil, B. (2016), "Why RC buildings failed in the 2011 Van, Turkey, earthquakes: construction versus design practices", J. Perform. Constr. Facil., 31(3), 04016110. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000980
  22. Fan, G., Wang, D. and Jia, J. (2018), "Improvement, analytical verification and application of RC frame beam-column joint models", Earthq. Struct., 14(3), 273-283. https://doi.org/10.12989/eas.2018.14.3.273.
  23. Filippou F.C. and Fenves G.L. (2004), "Methods of analysis for earthquake-resistant structures", Chapter 6 in Earthquake Engineering-From Engineering Seismology to Performance-Based Engineering, Eds. Y. Bozorgnia and V.V. Bertero, Cambridge University Press, Cambridge, United Kingdom.
  24. Fragiadakis, M. and Papadrakakis, M. (2008), "Modeling, analysis and reliability of seismically excited structures: computational issues", Int. J. Comput. Meth., 5(4), 483-511. https://doi.org/10.1142/S0219876208001674.
  25. Inel, M. and Meral, E. (2016), "Seismic performance of RC buildings subjected to past earthquakes in Turkey", Earthq. Struct., 11(3), 483-503. http://dx.doi.org/10.12989/eas.2016.11.3.483.
  26. Kappos, A.J. (1991), "Analytical prediction of the collapse earthquake for reinforced concrete buildings: suggested methodology", Earthq. Eng. Struct. Dyn., 20, 167-176. https://doi.org/10.1002/eqe.4290200206.
  27. Kim, J. and LaFave, M. (2012), "A simplified approach to joint shear behavior prediction of RC beam-column connections", Earthq. Spectra, 28(3), 1071-1096. https://doi.org/10.1193/1.4000064.
  28. Lima, C., Martinelli, E., Macorini, L. and Izzuddin, B.A. (2017), "Modelling beam-to-column joints in seismic analysis of RC frames", Earthq. Struct., 12(1), 119-133. https://doi.org/10.12989/eas.2017.12.1.119.
  29. Lowes, L.N. and Altoontash, A. (2003), "Modeling reinforced-concrete beam-column joints subjected to cyclic loading", ASCE J. Struct. Eng., 129(12), 1686-1697. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:12(1686).
  30. Neuenhofer, A. and Filippou F.C. (1997), "Evaluation of nonlinear frame finite-element models", J. Struct. Eng., ASCE, 123(7), 958-966. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:7(958).
  31. Newmark, N.M. and Hall, W. J., (1982), "Earthquake spectra and design", Earthquake Engineering Research Institute, Oakland, CA.
  32. Pampanin, S., Calvi, GM. and Moratti, M. (2002), "Seismic behavior of R.C. beam-column joints designed for gravity only", Proceedings of the 12th European Conference on Earthquake Engineering, Paper No. 726.
  33. Paulay and Priestley (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, John Wiley & Sons, Inc., NY, USA.
  34. Priestley, M.J.N. (1997), "Displacement-based seismic assessment of reinforced concrete buildings", J. Earthq. Eng., 1(1), 157-192. https://doi.org/10.1080/13632469708962365
  35. Quintana-Gallo, P., Pampanin, S., Carr, A.J. and Bonelli, P. (2010), "Shake table tests of under designed RC frames for the seismic retrofit of buildings-design and similitude requirements of the benchmark specimen", Proceedings of the New Zealand Society of Earthquake Engineering, Paper No. 39.
  36. Rashid, M. and Ahmad, N. (2017), "Economic losses due to earthquake-induced structural damages in RC SMRF structures", Cogent Eng., 4(1), 1-15.
  37. Rizwan, M., Ahmad, N. and Khan, A.N. (2018), "Seismic performance of compliant and noncompliant special momentresisting reinforced concrete frames", ACI Struct. J., 115(4), 1063-1073. https://doi.org/10.14359/51702063
  38. Rossetto, T. and Peiris, N., (2009), "Observations of damage due to the Kashmir earthquake of October 8, 2005 and study of current seismic provisions for buildings in Pakistan", Bull. Earthq. Eng., 7(3), 681-699. https://doi.org/10.1007/s10518-009-9118-5.
  39. Ruiz-Pinilla, J.G., Adam, J.M., Perez-Carcel, R., Yuste, J. and Moragues, J.J. (2016), "Learning from RC building structures damaged by the earthquake in Lorca, Spain, in 2011", Eng. Fail. Anal., 68, 76-86. https://doi.org/10.1016/j.engfailanal.2016.05.013.
  40. SeismoStruct (2016), SeismoStruct-Software: a computer program for static and dynamic nonlinear inelastic analysis of structures. Available from URL: www.seismosoft.com.
  41. Sharma, A., Reddy, G.R. and Vaze, K.K. (2012), "Shake table tests on a non-seismically detailed RC frame structure", Struct. Eng. Mech., 41(1), 1-24. https://doi.org/10.12989/sem.2012.41.1.001.
  42. Sivaselvan, M. and Reinhorn, A.M. (2001), "Hysteretic models for deteriorating inelastic structures", J. Eng. Mech., ASCE, 126(6), 633-640. https://doi.org/10.1061/(ASCE)0733-9399(2000)126:6(633)
  43. Spacone, E., Ciampi, V. and Filippou, F.C. (1996), "Mixed formulation of nonlinear beam finite element", Comput. Struct., 58(1), 71-83. https://doi.org/10.1016/0045-7949(95)00103-N.
  44. Vamvatsikos, D. and Cornell, C. (2002), "Incremental dynamic analysis", Earthq. Eng. Struct. Dyn., 31(3), 491-514. https://doi.org/10.1002/eqe.141.
  45. Youssef, M. and Ghobarah, A. (2001), "Modelling of RC beamcolumn joints and structural walls", J. Earthq. Eng., 5(1), 93-111. https://doi.org/10.1080/13632460109350387

피인용 문헌

  1. Force-based seismic design of steel haunch retrofit for RC frames vol.20, pp.2, 2019, https://doi.org/10.12989/eas.2021.20.2.133
  2. Shake table testing of confined adobe masonry structures vol.20, pp.2, 2021, https://doi.org/10.12989/eas.2021.20.2.149
  3. Shake-table testing of a 1:5 reduced-scale five-story masonry-infilled reinforced concrete frame structure vol.79, pp.3, 2019, https://doi.org/10.12989/sem.2021.79.3.373