DOI QR코드

DOI QR Code

Interaction between two neighboring tunnel using PFC2D

  • Sarfarazi, V. (Department of Mining Engineering, Hamedan University of Technology) ;
  • Haeri, Hadi (Department of Civil Engineering, Malard Branch, Islamic Azad University) ;
  • Safavi, Salman (Department of Civil Engineering, Malard Branch, Islamic Azad University) ;
  • Marji, Mohammad Fatehi (Mine Exploitation Engineering Department, Faculty of Mining and Metallurgy, Institution of Engineering, Yazd University) ;
  • Zhu, Zheming (MOE Key Laboratory of Deep Underground Science and Engineering, School of Architecture and Environment, Sichuan University)
  • 투고 : 2019.01.28
  • 심사 : 2019.03.20
  • 발행 : 2019.07.10

초록

In this paper, the interaction between two neighboring tunnel has been investigated using PFC2D. For this purpose, firstly calibration of PFC was performed using Brazilian experimental test. Secondly, various configuration of two neighboring tunnel was prepared and tested by biaxial test. The maximum and minimum principle stresses were 0.2 and 30 MPa respectively. The modeling results show that in most cases, the tensile cracks are dominant mode of cracks that occurred in the model. With increasing the diameter of internal circle, number of cracks decreases in rock pillar also number of total cracks decreases in the model. The rock pillar was heavily broken when its width was too small. In fixed quarter size of tunnel, the crack initiation stress decreases with increasing the central tunnel diameter. In fixed central tunnel size, the crack initiation stress decreases with increasing the quarter size of tunnel.

키워드

참고문헌

  1. Boumaaza, M., Bezazi, A., Bouchelaghem, H., Benzennache, N., Amziane, S. and Scarpa, F. (2017), "Behavior of pre-cracked deep beams with composite materials repairs", Struct. Eng. Mech., 63(4), 43-56.
  2. Chehade, F.H. and Shahrour, I. (2008), "Numerical analysis of the interaction between twin-tunnels: Influence of the relative position and construction procedure", Tunn. Undergr. Sp. Tech., 23, 210-214. https://doi.org/10.1016/j.tust.2007.03.004.
  3. Chen, R.P., Zhu, J., Liu, W. and Tang, X.W. (2011), "Ground movement induced by parallel EPB tunnels in silty soils", Tunnelling and Underground Space Technology, 26(1), 163-171. https://doi.org/10.1016/j.tust.2010.09.004.
  4. Chung, J.S., Moon, I.K. and Yoo, C.H. (2013), "Behaviour characteristics of tunnel in the cavity ground by using scale model tests", J. Korean Geo-Environ. Soc., 14(12), 61-69 https://doi.org/10.14481/jkges.2013.14.12.061
  5. Das, R., Singh, P.K., Kainthoal, A., Panthee, S. and Singh, T.N. (2017), "Numerical analysis of surface subsidence in asymmetric parallel highway tunnels", J. Rock Mech. Geotech. Eng., 9, 170-179. https://doi.org/10.1016/j.jrmge.2016.11.009.
  6. Donze, F.V., Richefeu, V. and Magnier, S.A. (2009), "Advances in discrete element method applied to soil rock and concrete mechanics", Electronic J. Geological Eng., 8, 1-44.
  7. Gercek, H. (2005), "Interaction between parallel underground openings", The 19th International Mining Congress and Fair of Turkey, Izmir, Turkey, June. 73-81.
  8. Ghaboussi, J. and Ranken, R.E. (1977), "Interaction between two parallel tunnels", Int. J. Numer. Anal. Met., 1(1), 75-103. https://doi.org/10.1002/nag.1610010107.
  9. Haeri, H., Sarfarazi, V. and Zhu, Z. (2018), "PFC3D simulation of the effect of particle size on the single edge-notched rectangle bar in bending test", Struct. Eng. Mech., 68(4), 497-505. http://dx.doi.org/10.12989/sem.2018.68.4.497.
  10. Haeri, H., Sarfarazi, V., Zhu, Z. and Moradizadeh, M. (2018), "The effect of ball size on the hollow center cracked disc (HCCD) in Brazilian test", Comput. Concrete, 22(4), 373-381. http://dx.doi.org/10.12989/cac.2018.22.4.373.
  11. Haeri, H., Sarfarazi, V. and Hedayat, A. (2016a), "Suggesting a new testing device for determination of tensile strength of concrete", Struct. Eng. Mech., 60(6), 939-952. http://dx.doi.org/10.12989/sem.2016.60.6.939.
  12. Haeri, H. and Sarfarazi, V. (2016), "Experimental study of shear behavior of planar non-persistent joint", Comput. Concrete, 17(5), 639-653. http://doi.org/10.12989/cac.2016.17.5.649.
  13. Haeri, H., Sarfarazi, V., Marji, M.F., Hedayat, A. and Zhu, Z. (2016b), "Experimental and numerical study of shear fracture in brittle materials with interference of initial double cracks", Acta Mechanica Solida, Sinica, 29(5), 555-566. https://doi.org/10.1016/S0894-9166(16)30273-7.
  14. Hsiao, F.Y., Wang, C.L. and Chern, J.C. (2009), "Numerical simulation of rock deformation for support design in tunnel intersection area", Tunn. Undergr. Sp. Tech., 24, 14-21. https://doi.org/10.1016/j.tust.2008.01.003.
  15. Huang, X., Huang, H. and Zhang, J. (2012), "Flattening of jointed shield-driven tunnel induced by longitudinal differential settlements", Tunnel. Underground Space Technol., 31, 20-32. https://doi.org/10.1016/j.tust.2012.04.002.
  16. Itasca Consulting Group Inc (2004), Particle flow code in 2-dimensions (PFC2D), Version 3.10, Minneapolis, Minnesota, USA.
  17. Jung, M.C., Hwang, J.S, Kim, J.S, Kim, S.W. and Baek, S.C. (2014), "Influence of the existing cavern on the stability of adjacent tunnel excavation by small-scale model tests," J. Korean Geo-Environ. Soc., 15(12), 117-128. https://doi.org/10.14481/jkges.2014.15.12.117
  18. Kang, J.G., Yang, H.S. and Jang, S.J. (2014), "Stability analysis of rock pillar in the diverging area of road tunnel", J. Korean Tunn. Undergr. Sp. Assoc., 24(5), 344-353. https://doi.org/10.7474/TUS.2014.24.5.344
  19. Yu, K. and Lu, Z. (2015), "Influence of softening curves on the residual fracture toughness of post-fire normal-strength concrete", Comput. Concrete, 15(2), 102-111. http://dx.doi.org/10.12989/cac.2015.15.2.199.
  20. Khodayar, A. and Nejati, H.R. (2018), "Effect of thermal-induced microcracks on the failure mechanism of rock specimens", Comput. Concrete, 22(1), 93-100. http://dx.doi.org/10.12989/cac.2018.22.1.093.
  21. Kim, J.H. and Kim, J.W. (2017), "Stability estimation of the pillar between twin tunnels considering various site conditions," J. Korean Tunn. Undergr. Sp. Assoc., 27(2), 109-119.
  22. Kim, J.K. and Lee, S. (2013), "A study on the estimation of the behaviors by compression method of rock pillar between close parallel tunnels", J. Korean Geotech. Soc., 29(12), 87-94 https://doi.org/10.7843/kgs.2013.29.12.87
  23. Kim, J.W. and Bae, W.S. (2008), "A study for the stability investigation of three parallel tunnels using scaled model tests," J. Korean Tunn. Undergr. Sp. Assoc., 18(4).
  24. Kim, W.B., Yang, H.S. and Ha, T.H. (2012), "An assessment of rock pillar behavior in very near parallel tunnel", J. Korean Tunn. Undergr. Sp. Assoc., 22(1), 60-68.
  25. Kovari, K. (2003), "History of the sprayed concrete lining method-part II: milestones up to the 1960s", Tunnel. Underground Space Technol., 18(1), 71-83. https://doi.org/10.1016/S0886-7798(03)00006-3.
  26. Li, X.G. and Yuan, D.J. (2012), "Response of a double-decked metro tunnel to shield driving of twin closely under-crossing tunnels", Tunnel. Underground Space Technol., 28, 18-30. https://doi.org/10.1016/j.tust.2011.08.005.
  27. Li, X., Yan, Z., Wang, Z. and Zhu, H. (2015), "Experimental and analytical study on longitudinal joint opening of concrete segmental lining", Tunnel. Underground Space Technol., 46, 52-63. https://doi.org/10.1016/j.tust.2014.11.002.
  28. Lim, H.M. and Son, K.R. (2014), "The stability analysis of near parallel tunnels pillar at multi-layered soil with shallow depth by numerical analysis", J. Korean Geo-Environ. Soc., 15(1), 53-62.
  29. Liu, H.Y., Small, J.C., Carter, J.P. and Williams, D.J. (2009), "Effects of tunnelling on existing support systems of perpendicularly crossing tunnels", Comput. Geotechnics, 36(5), 880-894. https://doi.org/10.1016/j.compgeo.2009.01.013.
  30. Marji, M.F., Hosseinmorshedy, A. and Shadpour, A. (2008), "On the boundary element analysis of stresses and strains around underground excavations in rocks", ISRM International Symposium - 5th Asian Rock Mechanics Symposium, Tehran, Iran, November.
  31. Monfared, M.M. (2017), "Mode III SIFs for interface cracks in an FGM coating-substrate system", Struct. Eng. Mech., 64(1), 78-95. http://dx.doi.org/10.12989/sem.2017.64.1.071.
  32. Nabil, B., Abdelkader, B., Miloud, A. and Noureddine, B. (2012), "On the mixed-mode crack propagation in FGMs plates: comparison of different criteria", Struct. Eng. Mech., 61(3), 201-213. http://dx.doi.org/10.12989/sem.2017.61.3.371.
  33. Nejati, H.R. and Ghazvinian, A. (2014), "Brittleness effect on rock fatigue damage evolution", Rock Mech. Rock Eng., 47(5), 1839-1848. https://doi.org/10.1007/s00603-013-0486-4.
  34. Pan, B., Gao, Y. and Zhong, Y. (2014), "Theoretical analysis of overlay resisting crack propagation in old cement concrete pavement", Struct. Eng. Mech., 52(4), 167-181. http://dx.doi.org/10.12989/sem.2014.52.4.829.
  35. Panaghi, K., Golshani, A. and Takemura, T. (2015), "Rock failure assessment based on crack density and anisotropy index variations during triaxial loading tests", Geomech. Eng., 9, 793-813. http://dx.doi.org/10.12989/gae.2015.9.6.793.
  36. Potyondy, D.O. and Cundall, P.A. (2004), "A bonded-particle model for rock", Int. J. Rock. Mech. Min. Sci., 41(8), 1329-1364. https://doi.org/10.1016/j.ijrmms.2004.09.011.
  37. Ramadoss, P. and Nagamani, K. (2013), "Stress-strain behavior and toughness of high-performance steel fiber reinforced concrete in compression", Comput. Concrete, 11(2), 55-65. http://dx.doi.org/10.12989/cac.2013.11.2.149.
  38. Rooh, A., Nejati, H. and Goshtasbi, K. (2018), "A new formulation for calculation of longitudinal displacement profile (LDP) on the basis of rock mass quality", Geomech. Eng., 6(5), 539-545. https://doi.org/10.12989/gae.2018.16.5.539.
  39. Sarfarazi, V. and Haeri, H.A. (2016), "Review of experimental and numerical investigations about crack propagation", Comput. Concrete, 18(2), 235-266. http://dx.doi.org/10.12989/cac.2016.18.2.235.
  40. Shi, J., Ng, C.W.W. and Chen, Y. (2015), "Three-dimensional numerical parametric study of the influence of basement excavation on existing tunnel", Comput. Geotechnics., 63, 146-158. https://doi.org/10.1016/j.compgeo.2014.09.002.
  41. Shin, J.H., Potts, D.M. and Zdravkovic, L. (2005), "The effect of pore-water pressure on NATM tunnel linings in decomposed granite soil", Canadian Geotechnical J., 42(6), 1585-1599. https://doi.org/10.1139/t05-072.
  42. Siahmansouri, A., Gholamnejad, J. and Marji, M.F. (2012), "A new method to predict ratio of width to height rock pillar in twin circular tunnels", J. Geol. Geosci, 1, 103. http://dx.doi.org/10.4172/2329-6755.1000103.
  43. Xie, J., Gunn, M.J. and Rahim, A. (2004), "Collapse analysis for two parallel circular tunnels with different diameters in soil" Proceedings of the Ninth International Symposium on Numerical Models in Geomechanics-NUMOG IX, Ottawa, Canada, August. 421-426.
  44. Ye, F., Gou, C. F., Sun, H. D., Liu, Y. P., Xia, Y. X. and Zhou, Z. (2014), "Model test study on effective ratio of segment transverse bending rigidity of shield tunnel", Tunnel. Underground Space Technol., 41, 193-205. https://doi.org/10.1016/j.tust.2013.12.011.
  45. Zhao, C. (2015), "Analytical solutions for crack initiation on floorstrata interface during mining", Geomech. Eng., 8, 237-255. https://doi.org/10.12989/gae.2015.8.2.237