Advances in concrete construction

  • 제7권4호
  • /
  • Pages.263-275
  • /
  • 2019
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Influence of mineral by-products on compressive strength and microstructure of concrete at high temperature

  • Sahani, Ashok Kr. (Department of Civil Engineering, NIT Durgapur) ;
  • Samanta, Amiya K. (Department of Civil Engineering, NIT Durgapur) ;
  • Roy, Dilip K. Singha (Department of Civil Engineering, NIT Durgapur)
  • 투고 : 2019.02.18
  • 심사 : 2019.04.19
  • 발행 : 2019.06.25
⟨ 이전 논문 다음 논문 ⟩

초록

In the present work, Granulated Blast Furnace Slag (GBFS) and Fly ash (FA) were used as partial replacement of Natural Sand (NS) and Ordinary Portland Cement (OPC) by weight. One control mix, one with GBFS, three with FA and three with GBFS-FA combined mixes were prepared. Replacements were 50% GBFS with NS and 20%, 30% and 40% FA with OPC. Preliminary investigation on development of compressive strength was carried out at 7, 28 and 90 days to ensure sustainability of waste materials in concrete matrix at room temperature. After 90days, thermo-mechanical study was performed on the specimen for a temperature regime of $200^{\circ}-1000^{\circ}C$ followed by furnace cooling. Weight loss, visual inspection along with colour change, residual compressive strength and microstructure analysis were performed to investigate the effect of replacement of GBFS and FA. Although adding waste mineral by-products enhanced the weight loss, their pozzolanicity and formation history at high temperature played a significant role in retaining higher residual compressive strength even up to $800^{\circ}C$. On detail microstructural study, it has been found that addition of FA and GBFS in concrete mix improved the density of concrete by development of extra calcium silicate gel before fire and restricts the development of micro-cracks at high temperature as well. In general, the authors are in favour of combined replacement mix in view of high volume mineral by-products utilization as fire protection.

키워드

참고문헌

  1. Ahn, Y.B., Jang, J.G. and Lee, H.K. (2016), "Mechanical properties of light weight concrete made with coal ashes after exposure to elevated temperature", Cement Concrete Compos., 72, 27-38. https://doi.org/10.1016/j.cemconcomp.2016.05.028.
  2. Al-Sahawneh, E.I. (2013), "Size effect and strength correction factors for normal weight concrete specimens under uniaxial compression stress", Contemp. Eng. Sci., 6(2), 57-68. https://doi.org/10.12988/ces.2013.13006
  3. Arioz, O. (2007), "Effects of elevated temperatures onproperties of concrete", Fire Saf. J., 42, 516-522. https://doi.org/10.1016/j.firesaf.2007.01.003.
  4. Bastami, M., Chaboki-Khiabani, A., Baghbadrani, M. and Kordi, M. (2011), "Performance of high strength concrete at elevated temperature", Scientia Iranica, 18(5), 1028-1036. https://doi.org/10.1016/j.scient.2011.09.001
  5. Bilir, T. (2012), "Effects of non-ground slag and bottom ash as fine aggregate on concrete permeability properties", Constr. Build. Mater., 26, 730-734. https://doi.org/10.1016/j.conbuildmat.2011.06.080.
  6. Binici, H., Aksogan, O., Gorur, E.B., Kaplan, H. and Bodur, M.N. (2008), "Performance of ground blastfurnace slag and ground basaltic pumice concrete against seawater attack", Constr. Build. Mater., 22(7), 1515-1526. https://doi.org/10.1016/j.conbuildmat.2007.03.024.
  7. CEB (1991), Fire Design of Concrete Structures in Accordance with CEB-FIP Model Code 90, Comite Euro-International duBeton (CEB), Bulletin d'Information 208, Lausanne, Switzerland.
  8. Chan, Y.N., Luo, X. and Sun, W. (2000), "Compressive strength and pore structure of high performance concrete after exposure to high temperature up to $800^{\circ}C$", Cement Concrete Res., 30(2), 247-251. https://doi.org/10.1016/S0008-8846(99)00240-9.
  9. Chan, Y.N., Peng, G.F. and Anson, M. (1999), "Residual strength and pore structure of high strength concrete and normal strength concrete after exposure to high temperatures", Cement Concrete Compos., 21(1), 23-27. https://doi.org/10.1016/S0958-9465(98)00034-1.
  10. Chen, G.M., He, Y.H., Yang, H., Chen, J.F. and Guo, Y.C. (2014), "Compressive behavior of steel fiber reinforced recycled aggregate concrete after exposure to elevated temperatures", Constr. Build. Mater., 71, 1-15. https://doi.org/10.1016/j.conbuildmat.2014.08.012.
  11. Cheng, A., Huang, R., Wu, J.K. and Chen, C.H. (2005), "Influence of GGBS on durability and corrosionbehavior of reinforced concrete", Mater. Chem. Phys., 93(2-3), 404-411. https://doi.org/10.1016/j.matchemphys.2005.03.043.
  12. Cheng, F.P., Kodur., V.K.R. and Wang, T.C. (2004), "Stress-strain curves for high strength concrete at elevated temperatures", J. Mater. Civil Eng., 16(1), 84-90. https://doi.org/10.1061/(ASCE)0899-1561(2004)16:1(84).
  13. Chi, J.H., Chen, C.T. and Huang, Y.L. (2012), "Fire-resistant property of reinforced light aggregate concrete wall", Constr. Build. Mater., 30, 725-733. https://doi.org/10.1016/j.conbuildmat.2011.12.081
  14. Cree, D. and Green, M. (2013), "Residual strength of concrete containing recycled materials after exposure to fire: A review", Constr. Build. Mater., 45, 208-223. https://doi.org/10.1016/j.conbuildmat.2013.04.005.
  15. Dash, M.K., Patro, S.K. and Rath, A.K. (2016), "Sustainable use of industrial-waste as partial replacementof fine aggregate for preparation of concrete-A review", Int. J. Sustain. Built Environ., 5(2), 484-516. https://doi.org/10.1016/j.ijsbe.2016.04.006.
  16. De Souza, A.A.A. and Moreno, A.L.J.R. (2010), "The effect of high temperatures on concrete compression strength, tensile strength and deformation modulus", IBRACON Struct. Mater. J., 3(4), 432-448. http://dx.doi.org/10.1590/S1983-41952010000400005.
  17. Demirel, B. and Kelestemur, O. (2010), "Effect of elevated temperature on the mechanical properties of concrete producedwith finely ground pumice and silica fume", Fire Saf. J., 45, 385-391. https://doi.org/10.1016/j.firesaf.2010.08.002.
  18. Dias, W.P.S., Khoury, G.A. and Sullivan, P.J.E. (1990), "Mechanical properties of hardened cement paste exposed to temperatures up to $700^{\circ}C$(1292 F)", ACI Mater. J., 87(2), 160-165.
  19. Djamila, B., Othmane, B., Said, K. and El-Hadj, K. (2018). "Combined effect of mineral admixture andcuring temperature on mechanical behavior and porosity of SCC", Adv. Concrete Constr., 6(1), 69-85. https://doi.org/10.12989/acc.2018.6.1.069.
  20. EN 1992-1-2 (2004), Eurocode 2: Design of Concrete Structures, Part1- 2: General Rules-Structural Fire Design (EN 1992-1-2), European Committee for Standarization, Brussels, Belgium.
  21. Fares, H., Noumowe, A. and Remond, S. (2009), "Selfconsolidating concrete subjected to high temperature: mechanical and physical chemical properties", Cement Concrete Compos., 39, 1230-1238. https://doi.org/10.1016/j.cemconres.2009.08.001.
  22. Feldman, R.F. and Ramachandran, V.S. (1971), "Differentiation of interlayer and adsorbed water in hydrated Portland cement on thermal analysis", Cement Concrete Res., 1(6), 607-620. https://doi.org/10.1016/0008-8846(71)90016-0.
  23. Georgali, B. and Tsakiridis, P.E. (2005), "Microstructure of firedamaged concrete", Cement Concrete Compos., 27, 255-259. https://doi.org/10.1016/j.cemconcomp.2004.02.022
  24. Go, C.G., Tang, J.R., Chi, J.H., Chen, C.T. and Huang, Y.L. (2012), "Fire-resistant property of reinforced lightaggregate concrete wall", Constr. Build. Mater., 30, 725-733. https://doi.org/10.1016/j.conbuildmat.2011.12.081
  25. Hager, I. (2013), "Behaviour of cement concrete at high temperature", Bull. Pol. Acad. Sci., 61(1), 145-154. https://doi.org/10.2478/bpasts-2013-0013.
  26. Hanaa, F., Albert, N. and Sebastien, R. (2009), "Self-consolidating concrete subjected to high temperature: mechanical and physicchemical properties", Cement Concrete Res., 39(12), 1230-1238. https://doi.org/10.1016/j.cemconres.2009.08.001.
  27. Hemalatha, T. and Sasmal, S. (2017), "Early-age strength development in fly ash blended cement composites: Investigation through chemical activation", Mag. Concrete Res., 71(5), 1-35. https://doi.org/10.1680/jmacr.17.00336.
  28. Hosam, E.D., Seleem, H., Rashad, M.A. and Elsokary, T. (2011), "Effect of elevated temperature on physico-mechanical properties of blended cement concrete", Constr. Build. Mater., 25, 1009-1017. https://doi.org/10.1016/j.conbuildmat.2010.06.078.
  29. IS 10262(2009), Specification for Guidelines for Concrete Mix Design Proportioning, Bureau of Indian Standard, New Delhi, India.
  30. IS 12269 (1987), Specifications for 53 Grade Portland Cement (IS12269: 1987), Bureau of Indian Standard, New Delhi, India.
  31. IS 3812(part 1) (2013), Specification for Pulverized Fuel Ash, Part 1: For Use as Pozzolana in Cement, Cement Mortar and Concrete, Bureau of Indian Standards, New Delhi, India.
  32. IS 383 (1970), Specifications for Coarse and Fine Aggregates from Natural Sources for Concrete, Bureau of Indian Standard, New Delhi, India.
  33. IS 456 (2000), Specification for Plain and Reinforced Concrete Code of Practice, Bureau of Indian Standard, New Delhi, India
  34. IS 516 (1959), Specifications for Methods of Tests for Strength of Concrete Methods, Bureau of Indian Standard, New Delhi, India.
  35. ISO 834: Part 1 (1987), Elements of Building Construction-General Requirements for Fire Resistance Testing, British Standards Institution, London.
  36. Khan, M.S., Prasad, J. and Abbas, H. (2013), "Effect of high temperature on high-volume fly ash concrete", Arab. J. Sci. Eng., 38, 1369-1378. https://doi.org/10.1007/s13369-013-0606-1.
  37. Khoury, G.A., Majorana, C.E., Pesavento, F. and Schrefler, B.A. (2002), "Modelling of heated concrete", Mag. Concrete Res., 54(2), 77-101. https://doi.org/10.1680/macr.2002.54.2.77.
  38. Kodur, V. (2014), "Properties of concrete at elevated temperature", ISRN Civil Eng., 2014, Article ID 468510, 15. http://dx.doi.org/10.1155/2014/468510.
  39. Lankard, D.R., Birkimer, D.L., Fondfriest, F. F. and Synder, M.J. (1971), "Effects of moisture content on the structure properties of Portland cement concrete exposed to temperatures up to $500^{\circ}F$", Spec. Publ., 25, 59-102.
  40. Lee, J., Choi, K. and Hong, K. (2009), "Color and material property changes in concrete exposed to high temperatures", J. Asian Arch. Build. Eng., 8(1), 175-182. https://doi.org/10.3130/jaabe.8.175.
  41. Li, G. and Zhao, X. (2003), "Properties of concrete incorporating fly ash and ground granulated blast-furnaceslag", Cement Concrete Compos., 25(3), 293-299. https://doi.org/10.1016/S0958-9465(02)00058-6.
  42. Li, Q., Li., Zh. and Yuan, G. (2012), "Effect of elevated temperature on properties of concrete containingground granulated blast furnace slag as cementitious material", Constr. Build. Mater., 35, 687-692. https://doi.org/10.1016/j.conbuildmat.2012.04.103.
  43. Lv, S., Liu, J., Sun, T., Ma, Y. and Zhou, Q. (2014), "Effect of GO nano-sheets on shapes of cement hydration crystals and their formation process", Constr. Build. Mater., 64, 231-239. https://doi.org/10.1016/j.conbuildmat.2014.04.061.
  44. Ma, Q., Guo, R., Zhao, Z. and He, K. (2015), "Mechanical properties of concrete at high temperature-A review", Constr. Build. Mater., 93, 371-383. https://doi.org/10.1016/j.conbuildmat.2015.05.131.
  45. Mohammadhosseini, H. and Tahir, Md. (2018), "Durability performance of concrete incorporating wastemetalized plastic fibres and palm oil fuel ash", Constr. Build. Mater., 180, 92-102. https://doi.org/10.1016/j.conbuildmat.2018.05.282.
  46. Mohammadhosseini, H. and Yatim, J.M. (2017), "Microstructure and residual properties of green concretecomposites incorporating waste carpet fibers and palm oil fuel ash at elevated temperatures", J. Clean. Prod., 144, 8-21. https://doi.org/10.1016/j.jclepro.2016.12.168.
  47. Mohammadhosseini, H., Shukor Lim, N.H.A., Mohd Sam, A.R. and Samadi, M. (2018), "Effects of elevated temperatures on residual properties of concrete reinforced with waste polypropylene carpet fibres", Arab. J. Sci. Eng., 43, 1673-1686. https://doi.org/10.1007/s13369-017-2681-1.
  48. Muttashar, H.L, Ali, N.B, Azreen, M., Ariffin, M. and Hussin, M.W. (2018), "Case study Microstructure and physical properties of waste garnets as a promising construction materials", Case Stud. Constr. Mater., 8, 87-96. https://doi.org/10.1016/j.cscm.2017.12.001.
  49. Nadeem, A., Memon, S.A. and Lo, T.Y. (2013), "Qualitative and quantitative analysis and identification of flaws in the microstructure of fly ash and metakaolin blended high performance concrete after exposure to elevated temperatures", Constr. Build. Mater., 38, 731-741. https://doi.org/10.1016/j.conbuildmat.2012.09.062.
  50. Nataraja, M.C., Kumar, P.G.D., Manu, A.S. and Sanjay, M.C. (2013), "Use of granulated blast furnace slag as fine aggregate in cement mortar", Int. J. Struct. Civil Eng. Res., 2(2), 59-68.
  51. Netinger, I., Kesegic, I. and Guljas, I. (2011), "The effect of high temperatures on the mechanical properties of concrete made with different types of aggregates", Fire Saf. J., 46, 425-430. https://doi.org/10.1016/j.firesaf.2011.07.002.
  52. Netinger, I., Varevac, D., Bjegovic, D. and Moric, D. (2013), "Effect of high temperature on properties of steel slag aggregate concrete", Fire Saf. J., 59, 1-7. https://doi.org/10.1016/j.firesaf.2013.03.008.
  53. Netinger, I.G., Jelcic, M.R. and Mladenovic, A. (2015), "Impact of high temperature on residual properties of concrete with steel slag aggregate", J. Mater. Civil Eng., 28(6), 04016013. https://doi.org/10.1061/(ASCE)MT.1943-5533.0001515.
  54. Neville, A.M. (2011), Properties of Concrete, 5th Edition, Pearson Education Limited, Harlow, England.
  55. Noumowe, A., Siddique, R. and Ranc, G. (2009), "Thermomechanical characteristics of concrete at elevated temperatures up to $300^{\circ}C$", Nucl. Eng. Des., 239, 470-476. https://doi.org/10.1016/j.nucengdes.2008.11.020.
  56. Oner, A., Akyuz, T.S. and Yildiza, R. (2005), "An experimental study on strength development of concrete containing fly ash and optimum usage of fly ash in concrete", Cement Concrete Res., 35, 1165-1117. https://doi.org/10.1016/j.cemconres.2004.09.031.
  57. O zkan, O ., Yuksel, I. and Muratoglu, O . (2007), "Strength properties of concrete incorporating coal bottom ashand granulated blast furnace slag", Waste Manage., 27, 161-167. https://doi.org/10.1016/j.wasman.2006.01.006.
  58. Pal, S.C., Mukherjee, A. and Pathak, S.R. (2003), "Investigation of hydraulic activity of ground granulated blastfurnace slag in concrete", Cement Concrete Res., 33, 1481-1486. https://doi.org/10.1016/S0008-8846(03)00062-0.
  59. Pathak, N. and Siddique, R. (2012), "Effects of elevated temperatures on properties of self-compacting-concrete containing fly ash and spent foundry sand", Constr. Build. Mater., 34, 512-521. https://doi.org/10.1016/j.conbuildmat.2012.02.026.
  60. Patra, K.R. and Mukharjee, B. (2017), "Influence of incorporation of granulated blast furnace slag as replacement of fine aggregate on properties of concrete", J. Clean. Prod., 165, 468-476. https://doi.org/10.1016/j.jclepro.2017.07.125.
  61. Patra, K.R. and Mukharjee, B. (2018), "Influence of granulated blast furnace slag as fine aggregate onproperties of cement mortar", Adv. Concrete Constr., 6(6), 611-629. https://doi.org/10.12989/acc.2018.6.6.611.
  62. Peng, G.F., Bian, S.H., Guo, Z.Q., Zhao, J., Peng, X.L. and Jiang, Y.C. (2008), "Effect of thermal shock due to rapid cooling on residual mechanical properties of fiber concrete exposed to high temperatures", Constr. Build. Mater., 22(5), 948-955. https://doi.org/10.1016/j.conbuildmat.2006.12.002.
  63. Poon, C.S., Azhar, S., Anson, M. and Wong, Y.L. (2001), "Comparison of the strength and durability performance of normal and high-strength pozzolanic concretes at elevated temperatures", Cement Concrete Res., 31, 1291-300. https://doi.org/10.1016/S0008-8846(01)00580-4.
  64. Ramlochan, T., Zacarias, P., Thomas, M.D.A. and Hootan, R.D. (2003), "The effect of pozzolans and slag on theexpansion of mortars cured at elevated temperature Part I: Expansive behaviour", Cement Concrete Res., 33, 807-814. https://doi.org/10.1016/S0008-8846(02)01066-9.
  65. Rashad, A.M., Sadek, D.M. and Hassan, H.A. (2016), "An investigation on blast-furnace slag as fine aggregatein alkaliactivated slag mortars subjected to elevated temperatures", J. Clean. Prod., 112, 1086-1096. https://doi.org/10.1016/j.jclepro.2015.07.127.
  66. Sahani, A.K., Samanta, A.K. and Singha Roy, D.K. (2015), "Sustainable concrete based on granular blast furnace slag as fine aggregate: Thermo-mechanical study", UKIERI Concrete Congress, Concrete Research Driving Profit and Sustainability, 883-889.
  67. Sahani, A.K., Samanta, A.K. and Singharoy, D.K. (2018), "Anexperimental study on strength development of concrete with optimum blending of fly ash and granulated blast furnace slag", Int. J. Appl. Eng. Res., 13(8), 5700-5710. https://doi.org/10.1016/j.cemconres.2004.09.031.
  68. Sahani, A.K., Samanta, A.K. and Singharoy, D.K. (2018), "Scope of granulated blast furnace slag as fineaggregate in concrete for normal and fire exposure", J. Urban Environ. Eng., 12(1), 40-49. https://doi.org/10.4090/juee.2018.v12n1.040049
  69. Samanta, A.K., Sahani, A.K. and Singha Roy, D.K. (2014), "Sustainable concrete structures with GBFS assuitable replacement of fine aggregate: A study on mechanical behaviour", 2nd Int. Conf. On Advances in Civil, Structural and Environ. Eng. ACSEE. https://doi.org/10.15224/ 978-1-63248-030-9-170.
  70. Sancak, E., Sari, Y.D. and Simsek, O. (2008), "Effects of elevated temperature on compressive strength and weight loss of the light-weight concrete with silica fume and super plasticizer", Cement Concrete Compos., 30, 715-721. https://doi.org/10.1016/j.cemconcomp.2008.01.004.
  71. Savya, A., Manita, P. and Sidris, K.K. (2005), "Influence of elevated temperatures on the mechanical properties of blended cement concretes prepared with limestone and siliceous aggregates", Cement Concrete Compos., 27, 239-248. https://doi.org/10.1016/j.cemconcomp.2004.02.013.
  72. Shoaib, M.M., Balaha, M.M. and Ahmed, S.A. (2000), "Influence of aggregate type on mortar thermal stability", Ind. J. Eng. Mater. Sci., 7, 217-224.
  73. Short, N.R., Purkiss, J.A. and Guise, S.E. (2001), "Assessment of fire damaged concrete using color imageanalysis", Constr. Build. Mater., 15(9), 9-15. https://doi.org/10.1016/S0950-0618(00)00065-9.
  74. Siddique, R. (2003), "Effect of fine aggregate replacement with Class F ash on the mechanical properties ofconcrete", Cement Concrete Res., 33(4), 539-547. https://doi.org/10.1016/S0008-8846(02)01000-1.
  75. Siddique, R. and Kaur, D. (2012), "Properties of concrete containing ground granulated blast furnace slag (GGBFS) at elevated temperatures", J. Adv. Res., 3, 45-51. https://doi.org/10.1016/j.jare.2011.03.004.
  76. Singha Roy, D.K. and Sai Krishna, P.C. (2012), "Effect of elevated temperature on physical properties of concrete", IUP J. Struct. Eng., 4(3), 32-42.
  77. Suhendro, B. (2014), "Toward green concrete for better sustainable environment", Procedia Eng., 95, 305-320. https://doi.org/10.1016/j.proeng.2014.12.190.
  78. Tang, W.C and Lo, T.Y (2009), "Mechanical and fracture properties of normal and high-strength concretes with fly ash after exposure to high temperature", Mag. Concrete Res., 61(5), 323-330. https://doi.org/10.1680/macr.2008.00084.
  79. Tanyildizi, H. and Coskun, A. (2008), "Performance of lightweight concrete with silica fume after high temperature", Constr. Build. Mater., 22, 2124-2149. https://doi.org/10.1016/j.conbuildmat.2007.07.017.
  80. Tanyildizi, H. and Coskun, A. (2008), "The effect of high temperature on compressive strength and split tensile strength of structural light concrete", Constr. Build. Mater., 22(11), 2269-2275. https://doi.org/10.1016/j.conbuildmat.2007.07.033.
  81. Xiuli, Y., Chong, C., Xiaoyu, C., Guodong, T. and Hailong, M.A. (2014), "High-temperature phasetransition and the activity of tobermorite", J. Wuhan. Univ. Technol., 29, 298-301. https://doi.org/10.1007/s11595-014-0911-x.
  82. Yuksel, I. and Genc, A. (2007), "Properties of concrete containing non-ground ash and slag as fine aggregate", ACI Mater. J., 104(4), 397-403.
  83. Yuksel, I., Siddique, R. and O zkan, O . (2011), "Influence of high temperature on the properties of concretemade with industrial by-products as fine aggregate replacement", Constr. Build. Mater., 25, 967-972. https://doi.org/10.1016/j.conbuildmat.2010.06.085.
  84. Zhang, B., Cullen, M. and Kilpatrick, T. (2016), "Spalling of heated high performance concretedue to thermal and hygric gradients", Adv. Concr. Constr., 4(1), 1-14. : http://dx.doi.org/10.12989/acc.2016.4.1.001.

피인용 문헌

  1. Evaluation of mathematical models for prediction of slump, compressive strength and durability of concrete with limestone powder vol.10, pp.6, 2019, https://doi.org/10.12989/acc.2020.10.6.463