Computers and Concrete

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Shear strength model for reinforced concrete beam-column joints based on hybrid approach

  • Parate, Kanak N. (Department of Applied Mechanics, Visvesvaraya National Institute of Technology) ;
  • Kumar, Ratnesh (Department of Applied Mechanics, Visvesvaraya National Institute of Technology)
  • Received : 2018.05.06
  • Accepted : 2019.04.13
  • Published : 2019.06.25
⟨ Previous Next ⟩

Abstract

Behavior of RC beam-column joint is very complex as the composite material behaves differently in elastic and inelastic range. The approaches generally used for predicting joint shear strength are either based on theoretical, strut-and-tie or empirical methods. These approaches are incapable of predicting the accurate response of the joint for entire range of loading. In the present study a new generalized RC beam-column joint shear strength model based on hybrid approach i.e. combined strut-and-tie and empirical approach has been proposed. The contribution of governing parameters affecting the joint shear strength under compression has been derived from compressive strut approach whereas; the governing parameters active under tension has been extracted from empirical approach. The proposed model is applicable for various conditions such as, joints reinforced either with or without shear reinforcement, joints with wide beam or wide column, joints with transverse beams and slab, joints reinforced with X-bars, different anchorage of beam bar, and column subjected to various axial loading conditions. The joint shear strength prediction of the proposed model has been compared with 435 experimental results and with eleven popular models from literature. In comparison to other eleven models the prediction of the proposed model is found closest to the experimental results. Moreover, from statistical analysis of the results, the proposed model has the least coefficient of variation. The proposed model is simple in application and can be effectively used by designers.

Keywords

References

  1. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete (ACI 318-14) and Commentary (ACI 318R-14), American Concrete Institute, Farmington Hills, Michigan.
  2. Anderson, M., Lehman, D. and Stanton, J. (2008), "A cyclic shear stress-strain model for joints without transverse reinforcement", Eng. Struct., 30(4), 941-954. https://doi.org/10.1016/j.engstruct.2007.02.005.
  3. Bakir, P.G. and Boduroglu, H.M. (2002), "A new design equation for predicting the joint shear strength of monotonically loaded exterior beam-column joints", Eng. Struct., 24(8), 1105-1117. https://doi.org/10.1016/S0141-0296(02)00038-X.
  4. Chun, S.C. and Kim, D.Y. (2004), "Evaluation of mechanical anchorage of reinforcement by exterior beam-column joint experiments", 13th World Conference on Earthquake Engineering, Paper No. 0326, Vancouver, B.C., Canada.
  5. Chun, S.C. and Shin, Y.S. (2014), "Cyclic testing of exterior beam-column joints with varying joint aspect ratio", ACI Struct. J., 111(3), 693-704. 1, https://doi.org/doi: 10.14359/51686730.
  6. European Committee for Standardization (CEN) (2004), Design of Structures for Earthquake Resistance, Part 1: General Rules, Seismic Actions and Rules for Buildings, Eurocode 8, BS EN 1998-1, BSI British Standards, London.
  7. Hakuto, S., Park, R. and Tanaka, H. (2000), "Seismic load tests on interior and exterior beam-column joints with substandard reinforcing details", ACI Struct. J., 97(1), 11-25.
  8. Hamil, S.J. (2000), "Reinforced concrete beam-column connection behavior", Ph.D. Thesis University of Durham, UK.
  9. Hegger, J., Sherif, A. and Roeser, W. (2003), "Nonseismic design of beam-column joints", ACI Struct. J., 100(5), 654-664.
  10. Hwang, S.J. and Lee, H.J. (2002), "Strength prediction for discontinuity regions by softened strut-and-tie model", J. Struct. Eng., ASCE, 128(12), 1519-1526. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:12(1519).
  11. Hwang, S.J., Lee, H.J., Liao, T.F., Wang, K.C. and Tsai, H.H. (2005), "Role of hoops on shear strength of RC beam-column joints", ACI Struct. J., 102(3), 445-453.
  12. IS 13920 (2016), Ductile Design and Detailing of Reinforced Concrete Structures Subjected to Seismic Forces, Code of Practice, India.
  13. Karayannis, C.G., Chalioris, C.E. and Sirkelis, G.M. (2008), "Local retrofit of exterior RC beam-column joints using thin RC jackets-An experimental study", Earthq. Eng. Struct. Dyn., 37(5), 727-746. https://doi.org/10.1002/eqe.783.
  14. Kassem, W. (2016), "Strut-and-tie modelling for the analysis and design of RC beam-column joints", Mater. Struct., 49(8), 3459-3476. https://doi.org/10.1617/s11527-015-0732-1.
  15. Kim, J. and LaFave, J.M. (2007), "Key influence parameters for the joint shear behavior of reinforced concrete (RC) beamcolumn connections", Eng. Struct., 29, 2523-2539. https://doi.org/10.1016/j.engstruct.2006.12.012.
  16. Kim, J., LaFave, J.M. and Song, J. (2009), "Joint shear behavior of reinforced concrete beam-column connections", Mag. Concrete Res., 61(2), 119-132. https://doi.org/10.1680/macr.2008.00068
  17. Lima, C., Martinelli, E. and Faella, C. (2012a), "Capacity models for shear strength of exterior joints in RC frames: state-of-theart and parametric comparisons", Bull. Earthq. Eng., 10, 967-983. https://doi.org/doi:10.1007/s10518-012-9340-4.
  18. Lima, C., Martinelli, E. and Faella, C. (2012b), "Shear strength of exterior beam-to-column reinforced concrete joints-Part. 2: assessment, recalibration and relevant factors", Bull. Earthq. Eng., 10, 985-1007. https://doi.org/doi:10.1007/ s10518-012-9342-2.
  19. Murty, C.V.R., Rai, D., Bajpai, K.K. and Jain, S.K. (2003), "Effectiveness of reinforcement details in exterior reinforced concrete beam-column joints for earthquake resistance", ACI Struct. J., 100(2), 149-156.
  20. Okahashi, Y. and Pantelides, C.P. (2017), "Strut-and-tie model for interior RC beam-column joints with substandard details retrofitted with CFRP jackets", Compos. Struct., 165, 1-8. https://doi.org/10.1016/j.compstruct.2017.01.004.
  21. Parate, K.N. and Kumar, R. (2016), "Investigation of shear strength models for exterior RC beam-column joint", Struct. Eng. Mech., 58(3), 475-514. https://doi.org/10.12989/sem.2016.58.3.475.
  22. Parate, K.N. and Kumar, R. (2019), "Shear strength criteria for design of RC beam-column joints in building codes", Bull. Earthq. Eng., 17(3), 1407-1493. https://doi.org/10.1007/s10518-018-0492-8.
  23. Parate, K.N. and Kumar, R. (2019), "Simplified empirical model for shear strength of RC beam-column joints", Asian J. Civil Eng., 20(1), 87-111. https://doi.org/10.1007/s42107-018-0090-8.
  24. Parate, K.N., Kumar, R. and Bakre, S.V. (2014), "A review on seismic behavior of RC beam-column joints", Proceedings in the 15th Symposium on Earthquake Engineering, IIT Roorkee, India.
  25. Park, S. and Mosalam, K.M. (2012), "Parameters for shear strength prediction of exterior beam-column joints without transverse reinforcement", Eng. Struct., 36,198-209. https://doi.org/10.1016/j.engstruct.2011.11.017.
  26. Parker, D.E. and Bullman, P.J.M. (1997), "Shear strength within reinforced concrete beam-column joints", Struct. Eng., 75(4), 53-57.
  27. Paulay, T. and Priestley, M. (1992), Seismic Design of Reinforced Concrete and Masonry Buildings, Wiley New York.
  28. Paulay, T., Park, R. and Priestley, M.J.N. (1978), "Reinforced concrete beam-column joints under seismic actions", ACI Struct. J., Title No. 75-60.
  29. Pauletta, M., Luca, D.D. and Russo, G. (2015), "Exterior beam column joints-shear strength model and design formula", Eng. Struct., 94, 70-81. https://doi.org/10.1016/j.engstruct.2015.03.040.
  30. Sarsam, K.F. and Phillips, M.E. (1985), "The shear design of insitu reinforced beam-column joints subjected to monotonic loading", Mag. Concrete Res., 37(130), 16-28. https://doi.org/10.1680/macr.1985.37.130.16.
  31. Standards Association of New Zealand (2006), The Design of Concrete Structures, NZS 3101:1995, Wellington, New Zealand.
  32. Tran, T.M., Hadi, M.N.S. and Pham, T.M. (2014), "A new empirical model for shear strength of reinforced concrete beamcolumn connections", Mag. Concrete Res., 66(10), 514-530. http://dx.doi.org/10.1680/macr.13.00310.
  33. Tsonos, A.G. (2007), "Cyclic load behavior of RC beam-column sub assemblages of modern structures", ACI Struct. J., 104(4), 468-78. https://doi.org/10.2495/ERES050421.
  34. Tsonos, A.G., Tegos, I.A. and Penelis, G. Gr. (1992), "Seismic resistance of type 2 exterior beam-column joints reinforced with inclined bars", ACI Struct. J., 89(1), 3-11.
  35. Vollum, R.L. and Newman, J.B. (1999), "Strut and tie models for analysis/design of external beam-column joints", Mag. Concrete Res., 51(6), 415-425. https://doi.org/10.1680/macr.1999.51.6.415
  36. Wang, G.L., Dai, G.L. and Teng, G.J. (2012), "Shear strength model for RC beam-column joints under seismic loading", Eng. Struct., 40, 350-360. https://doi.org/10.1016/j.engstruct.2012.02.038.
  37. Wong, H.F. (2005), "Shear strength and seismic performance of non-seismically designed RC beam-column joints", PhD Dissertation, Hong Kong University of Science and Technology.
  38. Wong, H.F. and Kuang, J.S. (2008), "Effects of beam-column depth ratio on joint seismic behavior", Proceedings of the Institution of Civil Engineers-Structures and Buildings, 161(2), 91-101. https://doi.org/10.1680/stbu.2008.161.2.91