Fig. 1. Developed product
Fig. 2. Process of injection molding by electronic heating
Fig. 3. Model of injection molding analysis
Fig. 4. Conditions of combined environmental test
Fig. 5. Position of microphone for measurement of the noise and vibration
Fig. 6. Comparison of simulation and experiment for analysis of cell distribution
Fig. 7. Comparison of simulation and experiment for analysis of surface characteristics.
Fig. 8. Cell size and Porosity by Mu-Cell method
Fig. 9. Surface roughness
Fig. 10. A combined environmental test setup
Fig. 11. Input frequency for vibration test
Table 1. Deformation after combined environmental test
Table 2. Amount of noise for vibration test
References
- D. H. Choi, H. T. Hwang, D. I. Son and D. I. Kim, A Study on Surface Improvement of Automotive Plastic Part by Injection Molding Analysis, J. Korean Inst. Surf. Eng. (2018) Fall conference 116.
- D. H. Choi, H. T. Hwang, D. I. Son and D. I. Kim, A Study on Surface Characteristics of Plastic Part with Mc-cell Process by Mold of Electronic Heating, J. Korean Inst. Surf. Eng. (2018) Fall conference 134.
- D. H. Choi, H. T. Hwang, D. I. Son and D. I. Kim, A Study of Surface Improvement for Automotive Part by Injection Mold of Electronic Heating, J. Korean Inst. Surf. Eng. 51 (2018) 40-46. https://doi.org/10.5695/JKISE.2018.51.1.40
- B. H. Kim and N. P. Suh, Low Thermal Inertia Molding, Polym Plast. Technol. Eng. 25 (1986) 73-93. https://doi.org/10.1080/03602558608070076
- K. M. B. Jansen and A. A. M. Flaman, Construction of Fast-response Heating Elements for Injection Molding Applications, Polym. Eng. Sci. 34 (1994) 894-897. https://doi.org/10.1002/pen.760341105
- D. Yao and B. Kim, Development of Rapid Heating and Cooling Systems for Injection Molding Applications, Polym. Eng. Sci. 42 (2002) 2471-2481. https://doi.org/10.1002/pen.11133
- D. Yao and B. Kim, Injection Molding High Aspect Ratio Microfeature, J. Injection Molding Tech. 6 (2002) 11-17.
- D. Klempner and K. C. Frisch, Handbook of Polymeric Foams and Foam Technology, Hanser, N.Y (1991).
- K. Yano, A. Uauki, A. Oakida, T. Kurauchi and O. Kamigaito, Synthesis and Properties of Polyimide-Clay Hybrid, J. Polym, Sci. Polym. Chem. 31 (1993) 2493. https://doi.org/10.1002/pola.1993.080311009
- A. Uauki, M. Kawasumi, Y. Kojima, Y. Fukushima, A. Oakda, T. Kurauchi and O. Kamigaito, Synthesis of Nylon6-Clay Hybrid, J. Mater. Res. 8 (1993) 1179. https://doi.org/10.1557/JMR.1993.1179
- J. Y. Chung and D. H. Kim, Development of Simulation Method for Heating Line Optimization of E-Mold by using Commercial CAE Softwares, J. Academia-Industrial Tech. 9 (2008) 1754-1759.
- S. L. Kang, Bubble Nucleation and Macroscopic Growth in Polymer Solutions, Chung-Ang University Graduation School Ph.D. Dissertation, (2005) 3-9.
- Y. C. Lee, The Improvement of Weldline and Flow mark Defection by using Injection Molding Analysis, J. Korean Soc. Precis. Eng. 30 (2013) 1295-1301. https://doi.org/10.7736/KSPE.2013.30.12.1295