DOI QR코드

DOI QR Code

Structural efficiency of various strengthening schemes for cold-formed steel beams: Effect of global imperfections

  • Dar, M. Adil (Department of Civil Engineering, Indian Institute Technology Delhi) ;
  • Subramanian, N. (Consulting Engineer) ;
  • Dar, A.R. (Department of Civil Engineering, National Institute Technology Srinagar) ;
  • Majid, Muheeb (Department of Civil Engineering, National Institute Technology Srinagar) ;
  • Haseeb, Mohd (Department of Civil Engineering, National Institute Technology Srinagar) ;
  • Tahoor, Mugees (Department of Civil Engineering, National Institute Technology Srinagar)
  • 투고 : 2018.10.22
  • 심사 : 2019.02.25
  • 발행 : 2019.02.25

초록

Cold-formed steel (CFS) has a great potential to meet the global challenge of fast-track and durable construction. CFS members undergo large buckling instabilities due to their small wall thickness. CFS beams with corrugated webs have shown great resistance towards web buckling under flexure, when compared to the conventional I-sections. However, the magnitude of global imperfections significantly affects the performance of CFS members. This paper presents the first attempt made to experimentally study the effect of global imperfections on the structural efficiency of various strengthening schemes implemented in CFS beams with corrugated webs. Different strengthening schemes were adopted for two types of beams, one with large global imperfections and the other with small imperfections. Strength and stiffness characteristics of the beams were used to evaluate the structural efficiency of the various strengthening schemes adopted. Six tests were performed with simply supported end conditions, under four-point loading conditions. The load vs. mid-span displacement response, failure loads and modes of failure of the test specimens were investigated. The test results would compensate the lack of experimental data in this area of research and would help in developing numerical models for extensive studies for the development of necessary guidelines on the same. Strengthening schemes assisted in enhancing the member performance significantly, both in terms of strength and stiffness. Hence, providing an economic and time saving solution to such practical structural engineering problems.

키워드

참고문헌

  1. AISI S-100 (2016), North American Specification for the Design of Cold-formed Steel Structural Members; AISI Standard, Washington, DC, USA.
  2. Ammash, H.K. (2017), "Shape optimization of innovation coldformed steel columns under uniaxial compressive loading", Jordan J. Civil Eng., 11(3), 473-489.
  3. Anbarasu, M. and Sukumar, S. (2014), "Influence of spacers on ultimate strength of intermediate length thin walled columns", Steel Compos. Struct., Int. J., 16(4), 437-454. https://doi.org/10.12989/scs.2014.16.4.437
  4. Biggs, K.A., Ramseyer, C., Ree, S. and Kang, T.H.K. (2015), "Experimental testing of cold-formed built-up members in pure compression", Steel Compos. Struct., Int. J., 18(6), 1331-1351 https://doi.org/10.12989/scs.2015.18.6.1331
  5. Dar, M.A., Dar, A.R., Yusuf, M. and Raju, J. (2015a), "Experimental study on innovative sections for cold formed steel beams, Steel Compos. Struct., Int. J., 19(6), 1599-1610. https://doi.org/10.12989/scs.2015.19.6.1599
  6. Dar, M.A., Subramanian, N., Dar, A.R. and Raju, J. (2015b), "Experimental investigations on the structural behaviour of a distressed bridge", Struct. Eng. Mech., Int. J., 56(4), 695-705. https://doi.org/10.12989/sem.2015.56.4.695
  7. Dar, M.A., Subramanian, N., Dar, A.R. and Raju, J. (2017), "Rehabilitation of a distressed steel roof truss - A study", Struct. Eng. Mech., Int. J., 62(5), 567-576.
  8. Dar, M.A., Sahoo, D.R., Pulikkal, S. and Jain, A.K. (2018a), "Behaviour of laced built-up cold-formed steel columns: Experimental investigation and numerical validation", Thin-Wall. Struct., 132, 398-409. https://doi.org/10.1016/j.tws.2018.09.012
  9. Dar, M.A., Subramanian, N., Dar, A.R., Anbarasu, M. and Lim, J.B.P. (2018b), "Structural performance of cold-formed steel composite beams", Steel Compos. Struct., Int. J., 27(5), 545-554.
  10. Dar, M.A., Subramanian, N., Dar, A.R., Anbarasu, M., Lim, J.B.P. and Mir, A. (2019), "Behaviour of partly stiffened cold-formed steel built-up beams: Experimental investigation and numerical validation", Adv. Struct. Eng., 22(1), 172-186. https://doi.org/10.1177/1369433218782767
  11. Dubina, D. and Ungureanu, V. (2002), "Effect of imperfections on numerical simulation of instability behaviour of cold-formed steel members", Thin Wall. Struct., 40, 239-262. https://doi.org/10.1016/S0263-8231(01)00046-5
  12. Dubina, D., Ungureanu, V. and Landolfo, R. (2012), Design of Cold-Formed Steel Structures, (First Edition), Wiley, New York.
  13. Dundu, M. (2012), "Base connections of single cold-formed steel portal frames", J. Constr. Steel Res., 78, 38-44. https://doi.org/10.1016/j.jcsr.2012.06.002
  14. El Aghoury, M.A., Salem, A.H., Hanna, M.T. and Amoush, E.A. (2013), "Strength of cold formed battened columns subjected to eccentric axial compressive force", J. Constr. Steel Res., 113, 58-70. https://doi.org/10.1016/j.jcsr.2015.04.008
  15. Gendy, B.L. and Hanna, M.T. (2015), "Effect of geometric imperfections on the ultimate moment capacity of cold-formed sigma-shape sections", HBRC Journal, 13(2), 163-170. https://doi.org/10.1016/j.hbrcj.2015.04.006
  16. Hancock, G.M. (2001), Cold-Formed Steel Designing and Analysis, Marcel Dekker, Sydney, Australia.
  17. Hancock, G.J. (2016), "Cold-formed steel structures, research review", Adv. Struct. Eng., 19(3), 393-408 https://doi.org/10.1177/1369433216630145
  18. IS 1608:2005 (2005), Indian Standard- Metallic Materials - Tensile Testing at Ambient Temperature; Bureau of Indian Standards, New Delhi, India, 1608-2005.
  19. IS 800:2007 (2007), Indian Standard Code of Practice for General Construction in Steel; Bureau of Indian Standards, New Delhi, India.
  20. IS 801:2010 (2010), Code of Practice for Use of Cold-Formed Light Gauge Steel Structural Members in General Building Construction, Bureau of Indian Standards, New Delhi, India.
  21. Kumar, N. and Sahoo, D.R. (2016), "Optimization of lip length and aspect ratio of thin channel sections under minor axes bending", Thin-Wall. Struct., 100, 158-169. https://doi.org/10.1016/j.tws.2015.12.015
  22. Kumar, G.A. and Sukumar, S. (2014), "A Simplified method for calculating warping constant for lipped I-beam with Trapezoidal corrugation in web", J. Struct. Eng. Madras, 40(6), 546-557.
  23. Martins, C.H., Ferreira, F.P.V., Rossi, A. and Trentini, E.V.W. (2017), "Numerical analysis of physical and geometrical imperfections in cellular beams", Open J. Civil Eng., 7, 116-129. https://doi.org/10.4236/ojce.2017.71007
  24. Saleh, A., Zahrai, S.M. and Seyed, R.M. (2016), "Experimental study on innovative tubular web RBS connections in steel MRFs with typical shallow beams", Struct. Eng. Mech., Int. J., 57(5), 785-808. https://doi.org/10.12989/sem.2016.57.5.785
  25. Serror, M.H., Soliman, E.G. and Hassan, A.F. (2017), "Numerical study on the rotation capacity of CFRP strengthened cold formed steel beams", Steel Compos. Struct., Int. J., 23(4), 385-397. https://doi.org/10.12989/scs.2017.23.4.385
  26. Soliman, M.S., Abu-Sena, A.B.B., Darwish, E.E.D. and Saleh, M.S.R. (2013), "Resistance of cold-formed steel sections to combined bending and web crippling", Ain Shams Eng. J., 4(3), 435-453. https://doi.org/10.1016/j.asej.2012.10.006
  27. Valsa Ipe, T., Sharada Bai, H., Manjulavani, K. and Iqbal, M.M.Z. (2013), "Flexural behavior of cold-formed steel-concrete composite beams", Steel Compos. Struct., Int. J., 14(2), 105-120. https://doi.org/10.12989/scs.2013.14.2.105
  28. Zhou, W. and Jiang, L. (2017), "Distortional buckling of coldformed lipped channel columns subjected to axial compression", Steel Compos. Struct., Int. J., 23(3), 331-338. https://doi.org/10.12989/scs.2017.23.3.331

피인용 문헌

  1. Flexural Strength of cold-formed steel built-up composite beams with rectangular compression flanges vol.34, pp.2, 2019, https://doi.org/10.12989/scs.2020.34.2.171
  2. Efficient cross-sectional profiling of built up CFS beams for improved flexural performance vol.34, pp.3, 2019, https://doi.org/10.12989/scs.2020.34.3.333
  3. An innovative technique of anchoring lacing bars with CFS sections for shear strengthening of RC beams vol.7, pp.1, 2019, https://doi.org/10.1007/s41062-021-00722-7