Journal of the Korean Society for Aeronautical & Space Sciences (한국항공우주학회지)

The Korean Society for Aeronautical and Space Sciences (한국항공우주학회)
권호 표지
DOI QR코드

DOI QR Code

Effect on Flow Distortion of S-Duct by Boundary Layer Suction

경계층 흡입이 S-Duct의 유동 왜곡에 미치는 영향성 연구

  • Baeg, Seungyong (Department of Mechanical Convergence Engineering, Hanyang University) ;
  • Lee, Jihyeong (Department of Mechanical Engineering, Hanyang University) ;
  • Cho, Jinsoo (School of Mechanical Engineering, Hanyang University)
  • Received : 2018.10.11
  • Accepted : 2018.12.28
  • Published : 2019.01.01
Download PDF
⟨ Previous Next ⟩

Abstract

An intake of Aircraft becomes S-shaped geometry due to spatial limitation or procuring survivability. But curvature of the S-shaped geometry makes secondary flow or flow separation which is the cause of non-uniform pressure distribution. In this study, boundary layer suction is applied to RAE M 2129 S-Duct by attaching sub duct. Design variable is suction location and angle. A mass flow rate drawn out by suction at the sub duct outlet is constant over every model. A grid dependency test was conducted to verify validity of computation. The comparison among the CFD (Computation Fluid Dynamics), ARA experimental result, and ARA computation result of non-dimensional pressure distribution on the Port side and Starboard Side confirmed the validity of CFD. In this study, Distortion Coefficient was used for evaluating aerodynamic performance of S-Duct. The analysis, which was about flow separation, vortex, mass flow rate distribution, and pressure distribution were also investigated. Maximum 26.14% reduction in Distortion Coefficient was verified.

항공기의 Intake는 공간적 제약 또는 생존성 확보의 이유로 S형태의 곡률을 갖는 덕트를 가진다. 그러나 덕트의 곡률은 2차유동과 유동박리의 발생을 야기하며 불균일한 압력분포 생성의 원인이 된다. 본 연구에서는 RAE M 2129 S-Duct의 형상에 보조 Duct를 적용하여 경계층 흡입을 수행하였다. 경계층 흡입의 위치와 각도를 설계변수로 설정하였으며, 흡입면에서 동일 유량을 흡입하는 조건을 부여하였다. S-Duct의 전산해석 타당성을 검증하기 위하여 Port Side와 Starboard Side의 무차원 압력 분포를 ARA 실험값, 전산해석 값과 각각 비교하여 확인하였다. 본 연구에서는 유동 왜곡을 판단하는 공기역학적 성능인자로 유동 왜곡 계수를 사용 하였으며, 경계층 흡입에 의한 유동박리, 와류, 유량 분포 및 압력 분포를 비교 분석 하였다. 그 결과 경계층 흡입 적용 이전과 비교하여 최대 26.14%의 유동 왜곡 계수 저감 효과를 확인하였다.

Keywords

References

  1. Menzies, R., "Computational Investigation of Flows in Diffusing S-Shaped Intakes," Acta 76. Polytechnia, Vol. 41, No. 4-5. 2001, pp.61-67.
  2. Menzies, R., "Investigation of S-shaped Intake Aerodynamics using Computational Fluid Dynamics," Ph. D. thesis, Department of Aerospace Engineering, University of Glasgaw, 2002.
  3. Reichert, B. A., and Wendt, B. J., "Improving Curved Subsonic Diffuser Performance with Vortex Generators," AIAA Journal, Vol. 34, No. 1, 1996, pp.65-72. https://doi.org/10.2514/3.13022
  4. Jirasek, A., "Design of Vortex Generator Flow Control in Inlets," Journal of Aircraft, Vol. 43, No. 6, 2006, pp.1886-1892. https://doi.org/10.2514/1.21364
  5. Yi, J., Lee, B., and Kim, C., "Design Optimization of Vortex Generator for Controlling Flows inside subsonic Diffusing S-duct," Proceeding of The Korean Society for Aeronautical and Space Science Fall Conference. November 2011, pp.294-299.
  6. Sullerey, R. K., Mishra, S., Pradeep, A. M., "Application of boundary layer fences and vortex generators in improving performance of S-Duct diffuser," Journal of Fluid Engineering, Vol. 124, No. 1, 2002 pp.136-142. https://doi.org/10.1115/1.1436096
  7. Choe, Y., and Kim, C., "Numerical Study on Performance of Supersonic Inelt under Various Bleed Conditions," Proceeding of The Korean Society for Aeronautical and Space Sciences Fall Conference, November 2014, pp.44-47.
  8. Debiasi, M., Herberg, M. R., Yan, Z., Dhanabalan, S. S., and Tsai, H. M., "Control of Flow Separation in S-ducts via Flow Injection and Suction," AIAA Aerospace Science meeting and Exhibition, 46th, January 2008.
  9. Scribben, A. R., NG, W., and Burdisso, R., "Effectiveness of a Serpentine Inlet Duct Flow Control Technique at Design and Off-Design Simulated Flight Conditions," ASME, Vol. 128, 2006, pp.332-339.
  10. Ball, W. H., "Test of Wall Suction and Blowing in Highly Offset Diffusers," AIAA, Vol. 22, No. 3, 1985, pp.161-167.
  11. Keerthi, M. C., and Kushari. A, "Effectiveness of vortex generator jets and wall suction on separated flows in serpentine-duct diffuser," Aerospace Science and Technology, Vol. 34, April 2014, pp.12-19 https://doi.org/10.1016/j.ast.2014.01.013
  12. Berens, T. M., Delot, A., Chevalier, M., Muijden, J. V., Waaijer, R. A., and Tattersall, P., "Garteur AD/AG-43 Application of CFD High Offset intake diffusers." GARTEUR Final Report, 2012.
  13. Menter, F. R., "Two-equation eddy viscosity turbulence models for engineering applications," AIAA Journal, Vol.32, No. 8, 1994, pp.1598-1605. https://doi.org/10.2514/3.12149
  14. Lee, J., and Cho, J., "Effect of aspect ratio of elliptical inlet shape on performance of subsonic diffusing S-duct," Journal of Mechanical Science ant Technology, Vol. 32, Issue. 3, March 2018, pp. 1153-1160 https://doi.org/10.1007/s12206-018-0218-5
  15. May, N. E., "The Prediction of Intake/S-bend Diffuser Flow using Varidus Two-Equation Turbulence Model Variants, Including Non-Linear Eddy Viscosity Formulations," ARA. Contractor Report M316/1, March 1997.
  16. AGARD, "Air Intakes for high Speed Vehicles," AGARD ADVISORY 270, Fluid Dynamics Panel Working Group 13, 1991.
  17. THYE, N. Y., "A Study of the Flow in and S-shaped Duct," ph. D. thesis, Department of mechanical engineering, National University of Singapore, 2009.