DOI QR코드

DOI QR Code

Influence of plastic viscosity of mix on Self-Compacting Concrete with river and crushed sand

  • Rama, J.S. Kalyana (Department of Civil Engineering, BITS Pilani, Hyderabad Campus) ;
  • Sivakumar, M.V.N. (Department of Civil Engineering, National Institute of Technology) ;
  • Kubair, K. Sai (Department of Civil Engineering, BITS Pilani, Hyderabad Campus) ;
  • Vasan, A. (Department of Civil Engineering, BITS Pilani, Hyderabad Campus)
  • 투고 : 2018.06.01
  • 심사 : 2019.01.22
  • 발행 : 2019.01.25

초록

In view of the increasing utility of concrete as a construction material, the major challenge is to improve the quality of construction. Nowadays the common problem faced by many of the concrete plants is the shortage of river sand as fine aggregate material. This led to the utilization of locally available materials from quarries as fine aggregate. With the percentage of fines present in Crushed Rock Fines (CRF)or crushed sand is more compared to river sand, it shows a better performance in terms of fresh properties. The present study deals with the formulation of SCC mix design based on the chosen plastic viscosity of the mix and the measured plastic viscosity of cement pastes incorporating supplementary cementitious materials with CRF and river sand as a fine aggregate. Four different combinations including two binary and one ternary mix are adopted for the current study. Influence of plastic viscosity of the mix on the fresh and hardened properties are investigated for SCC mixes with varying water to cement ratios. It is observed that for an increasing plastic viscosity of the mix, slump flow, T500 and J-ring spread increased but V-funnel and L-box decreased. Compressive, split tensile and flexural strengths decreased with the increase in plastic viscosity.

키워드

참고문헌

  1. Abo Dhaheer, M.S., Al-Rubaye, M.M., Alyhya, W.S., Karihaloo, B.L. and Kulasegaram, S. (2016), "Proportioning of self-compacting concrete mixes based on target plastic viscosity and compressive strength: Part I-mix design procedure", J. Sustain. Cement-Bas. Mater., 5(4), 199-216. https://doi.org/10.1080/21650373.2015.1039625
  2. Abo Dhaheer, M.S., Al-Rubaye, M.M., Alyhya, W.S., Karihaloo, B.L. and Kulasegaram, S. (2016), "Proportioning of self-compacting concrete mixes based on target plastic viscosity and compressive strength: Part II-experimental validation", J. Sustain. Cement-Bas. Mater., 5(4), 217-232. https://doi.org/10.1080/21650373.2015.1036952
  3. ASTM (American Society for Testing and Materials) (2014), C 1621/C 1621M: Standard Test Method for Passing Ability of Self-Consolidating Concrete by J-Ring.
  4. Bentz, D.P., Garboczi, E.J., Haecker, C.J. and Jensen, O.M. (1999), "Effects of cement particle size distribution on performance properties of Portland cement-based materials", Cement Concrete Res., 29(10), 1663-1671. https://doi.org/10.1016/S0008-8846(99)00163-5
  5. Beycioglu, A. and Aruntas, H.Y. (2014), "Workability and mechanical properties of self-compacting concretes containing LLFA, GBFS and MC", Constr. Build. Mater., 73, 626-635. https://doi.org/10.1016/j.conbuildmat.2014.09.071
  6. BIS (Bureau of Indian Standards) (1970), 383: Specification for Coarse and Fine Aggregates from Natural Sources for Concrete, India.
  7. Boukendakdji, O., Kadri, E.H. and Kenai, S. (2012), "Effects of granulated blast furnace slag and superplasticizer type on the fresh properties and compressive strength of self-compacting concrete", Cement Concrete Compos., 34(4), 583-590. https://doi.org/10.1016/j.cemconcomp.2011.08.013
  8. Chen, Y.Y., Tuan, B.L.A. and Hwang, C.L. (2013), "Effect of paste amount on the properties of self-consolidating concrete containing fly ash and slag", Constr. Build. Mater., 47, 340-346. https://doi.org/10.1016/j.conbuildmat.2013.05.050
  9. Chow, R.K., Yip, S.W. and Kwan, A.K. (2013), "Processing crushed rock fine to produce manufactured sand for improving overall performance of concrete", HKIE Tran., 20(4), 240-249. https://doi.org/10.1080/1023697X.2013.861186
  10. Concrete fact sheet, www.nrmca.org. (Browsed on 27/10/2016)
  11. Corinaldesi, V. and Moriconi, G. (2011), "The role of industrial by-products in self-compacting concrete", Constr. Build. Mater., 25(8), 3181-3186. https://doi.org/10.1016/j.conbuildmat.2011.03.001
  12. Dinakar, P., Sethy, K.P. and Sahoo, U.C. (2013), "Design of self-compacting concrete with ground granulated blast furnace slag", Mater. Des., 43, 161-169. https://doi.org/10.1016/j.matdes.2012.06.049
  13. Dransfield, J. (2003), "Mortar and grout", Advanced Concrete Technology 1: Constituent Materials, 69.
  14. EFNARC, S. (2002), Guidelines for Self-Compacting Concrete, EFNARC, UK.
  15. Fathi, H. and Lameie, T. (2017), "Effect of aggregate type on heated self-compacting concrete", Comput. Concrete, 19(5), 33-39. https://doi.org/10.12989/cac.2017.19.1.033
  16. Ferraris, C.F., Brower, L.E. and Banfill, P. (2001), "Comparison of Concrete Rheometers: International Test at LCPC (Nantes, France) in October", National Institute of Standards and Technology, Gaithersburg, MD, USA.
  17. Gandage, A.S., Rao, V.V., Sivakumar, M.V.N., Vasan, A., Venu, M. and Yaswanth, A.B. (2013), "Effect of perlite on thermal conductivity of Self-Compacting Concrete", Procedia-Soc. Behav. Sci., 104, 188-197. https://doi.org/10.1016/j.sbspro.2013.11.111
  18. Gesoglu, M., Guneyisi, E. and Ozbay, E. (2009), "Properties of self-compacting concretes made with binary, ternary, and quaternary cementitious blends of fly ash, blast furnace slag, and silica fume", Constr. Build. Mater., 23(5), 1847-1854. https://doi.org/10.1016/j.conbuildmat.2008.09.015
  19. Ghanbari, A. and Karihaloo, B.L. (2009), "Prediction of the plastic viscosity of self-compacting steel fibre reinforced concrete", Cement Concrete Res., 39(12), 1209-1216. https://doi.org/10.1016/j.cemconres.2009.08.018
  20. Hocevar, A., Kavcic, F. and Bokan-Bosiljkov, V. (2012), "Rheological parameters of fresh concrete-comparison of rheometers", GRADEVINAR, 65(2), 99-109
  21. Khan, A., Do, J. and Kim, D. (2016), "Cost effective optimal mix proportioning of high strength self-compacting concrete using response surface methodology", Comput. Concrete, 17(5), 629-638. https://doi.org/10.12989/cac.2016.17.5.629
  22. Khatib, J.M. (2008), "Performance of self-compacting concrete containing fly ash", Constr. Build. Mater., 22(9), 1963-1971. https://doi.org/10.1016/j.conbuildmat.2007.07.011
  23. Khayat, K.H. (1999), "Workability, testing, and performance of self-consolidating concrete", ACI Mater. J., 96, 346-353.
  24. Khayat, K.H. and Guizani, Z. (1997), "Use of viscosity-modifying admixture to enhance stability of fluid concrete", ACI Mater. J., 94(4), 332-340.
  25. Krieger, I.M. and Dougherty, T.J. (1959), "A mechanism for non-Newtonian flow in suspensions of rigid spheres", Tran. Soc. Rheol., 3(1), 137-152. https://doi.org/10.1122/1.548848
  26. Liu, M. (2010), "Self-compacting concrete with different levels of pulverized fuel ash", Constr. Build. Mater., 24(7), 1245-1252. https://doi.org/10.1016/j.conbuildmat.2009.12.012
  27. Long, W.J., Gu, Y., Liao, J. and Xing, F. (2017), "Sustainable design and ecological evaluation of low binder self-compacting concrete", J. Clean. Prod., 167, 317-325. https://doi.org/10.1016/j.jclepro.2017.08.192
  28. Mahdikhani, M. and Ramezanianpour, A.A. (2014), "Mechanical properties and durability of self-consolidating cementitious materials incorporating nano silica and silica fume", Comput. Concrete, 14(2), 175-191. https://doi.org/10.12989/cac.2014.14.2.175
  29. Mindess, S., Young, J.F. and Darwin, D. (2003), Concrete, Prentice Hall.
  30. Mohebbi, A., Shekarchi, M., Mahoutian, M. and Mohebbi, S. (2011), "Modeling the effects of additives on rheological properties of fresh self-consolidating cement paste using artificial neural network", Comput. Concrete, 8(3), 279-292. https://doi.org/10.12989/cac.2011.8.3.279
  31. Mundra, S., Sindhi, P.R., Chandwani, V., Nagar, R. and Agrawal, V. (2016), "Crushed rock sand-An economical and ecological alternative to natural sand to optimize concrete mix", Perspect. Sci., 8, 345-347. https://doi.org/10.1016/j.pisc.2016.04.070
  32. Nepomuceno, M.C., Pereira-de-Oliveira, L.A. and Lopes, S.M.R. (2014), "Methodology for the mix design of self-compacting concrete using different mineral additions in binary blends of powders", Constr. Build. Mater., 64, 82-94. https://doi.org/10.1016/j.conbuildmat.2014.04.021
  33. Okamura, H. (1995), "Ozawa, and Kazumasa: 'Mix design for self-compacting concrete'concrete", Library of JSCE No. 25.
  34. Okamura, H. and Ouchi, M. (2003), "Self-compacting concrete", J. Adv. Concrete Technol., 1(1), 5-15. https://doi.org/10.3151/jact.1.5
  35. Ozawa, K. (1989), "High performance concrete based on the durability design of concrete structures", The Second East Asia-Pacific Conference on Structural Engineering & Construction.
  36. Ozawa, K. and Ouchi, M. (1999) "Proceedings of the international workshop on Self-Compacting Concrete", Kochi.
  37. Pathak, S.S., Sharma, S., Sood, H. and Khitoliya, R.K. (2012), "Prediction of compressive strength of Self Compacting Concrete with flyash and rice husk ash using adaptive neuro-fuzzy inference system", Editorial Preface, 3(10), 112-118.
  38. Raheman, A. and Modani, P.O. (2013), "Prediction of properties of Self Compacting Concrete using artificial neural network", Int. J. Eng. Res. Appl. (IJERA), 3(4), 333-339.
  39. Shi, C., Wu, Z., Lv, K. and Wu, L. (2015), "A review on mixture design methods for self-compacting concrete", Constr. Build. Mater., 84, 387-398. https://doi.org/10.1016/j.conbuildmat.2015.03.079
  40. Siddique, R., Aggarwal, P. and Aggarwal, Y. (2011), "Prediction of compressive strength of self-compacting concrete containing bottom ash using artificial neural networks", Adv. Eng. Softw., 42(10), 780-786. https://doi.org/10.1016/j.advengsoft.2011.05.016
  41. Struble, L. and Sun, G.K. (1995), "Viscosity of portland cement paste as a function of concentration", Adv. Cement Bas. Mater., 2(2), 62-69. https://doi.org/10.1016/1065-7355(95)90026-8
  42. Uysal, M. and Sumer, M. (2011), "Performance of self-compacting concrete containing different mineral admixtures", Constr. Build. Mater., 25(11), 4112-4120. https://doi.org/10.1016/j.conbuildmat.2011.04.032
  43. Uysal, M. and Tanyildizi, H. (2012), "Estimation of compressive strength of self compacting concrete containing polypropylene fiber and mineral additives exposed to high temperature using artificial neural network", Constr. Build. Mater., 27(1), 404-414. https://doi.org/10.1016/j.conbuildmat.2011.07.028
  44. Uysal, M., Yilmaz, K. and Ipek, M. (2012), "Properties and behavior of self-compacting concrete produced with GBFS and FA additives subjected to high temperatures", Constr. Build. Mater., 28(1), 321-326. https://doi.org/10.1016/j.conbuildmat.2011.08.076
  45. Uysal, M., Yilmaz, K. and Ipek, M. (2012), "The effect of mineral admixtures on mechanical properties, chloride ion permeability and impermeability of self-compacting concrete", Constr. Build. Mater., 27(1), 263-270. https://doi.org/10.1016/j.conbuildmat.2011.07.049
  46. Van Der Vurst, F., Grunewald, S., Feys, D., Lesage, K., Vandewalle, L., Vantomme, J. and De Schutter, G. (2017), "Effect of the mix design on the robustness of fresh self-compacting concrete", Cement Concrete Compos., 82, 190-201. https://doi.org/10.1016/j.cemconcomp.2017.06.005
  47. Wongkeo, W., Thongsanitgarn, P., Ngamjarurojana, A. and Chaipanich, A. (2014), "Compressive strength and chloride resistance of self-compacting concrete containing high level fly ash and silica fume", Mater. Des., 64, 261-269. https://doi.org/10.1016/j.matdes.2014.07.042