Structural Engineering and Mechanics

  • 제68권4호
  • /
  • Pages.497-505
  • /
  • 2018
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

PFC3D simulation of the effect of particle size on the single edge-notched rectangle bar in bending test

  • Haeri, Hadi (MOE Key Laboratory of Deep Underground Science and Engineering, School of Architecture and Environment, Sichuan University) ;
  • Sarfarazi, Vahab (Department of Mining Engineering, Hamedan University of Technology) ;
  • Zhu, Zheming (MOE Key Laboratory of Deep Underground Science and Engineering, School of Architecture and Environment, Sichuan University)
  • 투고 : 2018.08.02
  • 심사 : 2018.10.11
  • 발행 : 2018.11.25
⟨ 이전 논문 다음 논문 ⟩

초록

Three points bending flexural test was modeled numerically to study the crack propagation in the pre-cracked beams. The pre-existing edge cracks in the beam models were considered to investigate the crack propagation and coalescence paths within the modeled samples. The effects of particle size on the single edge-notched round bar in bending test were considered too. The results show that Failure pattern is constant by increasing the ball diameter. Tensile cracks are dominant mode of failure. These crack initiates from notch tip, propagate parallel to loading axis and coalescence with upper model boundary. Number of cracks increase by decreasing the ball diameter. Also, tensile fracture toughness was decreased with increasing the particle size. In the present study, the influences of particles sizes on the cracks propagations and coalescences in the brittle materials such as rocks and concretes are numerically analyzed by using a three dimensional particle flow code (PFC3D). These analyses improve the understanding of the stability of rocks and concretes structures such as rock slopes, tunnel constructions and underground openings.

키워드

참고문헌

  1. Akbas S, (2016), "Analytical solutions for static bending of edge cracked micro beams", Struct. Eng. Mech., 59(3), 66-78.
  2. Ameen, M., Raghu Prasad, B.K. and Gopalakrishnan, A.R. (2011), "Modeling of concrete cracking-a hybrid technique of using displacement discontinuity element method and direct boundary element method", Eng. Analy. Bound. Elem., 35(9), 1054-1059. https://doi.org/10.1016/j.enganabound.2011.03.009
  3. Belytschko, T. and Black, T. (1999), "Elastic crack growth in finite elements with minimal remeshing", Int. J. Numer. Meth. Eng., 45(5), 601-620. https://doi.org/10.1002/(SICI)1097-0207(19990620)45:5<601::AID-NME598>3.0.CO;2-S
  4. Bi, J., Zhou, X.P. and Qian, Q.H. (2016), "The 3D Numerical simulation for the propagation process of multiple pre-existing flaws in rock-like materials subjected to biaxial compressive loads", Rock Mech. Rock Eng., 49(5), 1611-1627. https://doi.org/10.1007/s00603-015-0867-y
  5. Bi, J., Zhou, X.P. and Xu, X.M. (2017), "Numerical simulation of failure process of rock-like materials subjected to impact loads", Int. J. Geomech., 17(3), 04016073 https://doi.org/10.1061/(ASCE)GM.1943-5622.0000769
  6. Bobet, A. (2000), "The initiation of secondary cracks in compression", Eng. Fract. Mech., 66(2), 187-219. https://doi.org/10.1016/S0013-7944(00)00009-6
  7. Bombolakis, E.G. (1968), "Photoelastic study of initial stages of brittle fracture in compression", Tectonophys., 6(6), 461-473. https://doi.org/10.1016/0040-1951(68)90072-3
  8. Cundall, P.A. and Strack, O.D.L. (1979), "A discrete numerical model for granular assemblies", Geotech., 29(1), 47-65. https://doi.org/10.1680/geot.1979.29.1.47
  9. Donze, F.V., Richefeu, V. and Magnier, S.A. (2009), "Advances in discrete element method applied to soil rock and concrete mechanics", Electr. J. Geol. Eng., 8(1), 1-44.
  10. Erdogan, F. and Sih, G.C. (1963), "On the crack extension path in plates under plane loading and transverse shear", ASME J. Bas. Eng., 85(4), 519-527.
  11. Fan, Y., Zhu, Z., Kang, J. and Fu, Y. (2016), "The mutual effects between two unequal collinear cracks under compression", Math. Mech. Sol., 22, 1205-1218.
  12. Freund, L.B. (1973), "Crack propagation in elastic solid subjected to general loading. Stress wave loading", J. Mech. Phys. Sol., 21(2), 47-61. https://doi.org/10.1016/0022-5096(73)90029-X
  13. Gerges, N., Issa, C. and Fawaz, S. (2015), "Effect of construction joints on the splitting tensile strength of concrete", Case Stud. Constr. Mater., 3, 83-91. https://doi.org/10.1016/j.cscm.2015.07.001
  14. Ghazvinian, A., Sarfarazi, V., Schubert, W. and Blumel, M. (2012), "A study of the failure mechanism of planar nonpersistent open joints using PFC2D", Rock Mech. Rock Eng., 45(5), 677-693. https://doi.org/10.1007/s00603-012-0233-2
  15. Haeri, H. (2015b), "Propagation mechanism of neighboring cracks in rock-like cylindrical specimens under uniaxial compression", J. Min. Sci., 51(3), 487-496. https://doi.org/10.1134/S1062739115030096
  16. Haeri, H., Sarfarazi, V., Fatehi, M., Hedayat, A. and Zhu, Z. (2016c), "Experimental and numerical study of shear fracture in brittle materials with interference of initial double", Acta Mech. Soild. Sinic., 5, 555-566.
  17. Haeri, H. (2015a), "Influence of the inclined edge notches on the shear-fracture behavior in edge-notched beam specimens", Comput. Concrete, 16(4), 605-623. https://doi.org/10.12989/cac.2015.16.4.605
  18. Haeri, H. (2016), "Propagation mechanism of neighboring cracks in rock-like cylindrical specimens under uniaxial compression", J. Min. Sci., 51(5), 1062-1106.
  19. Haeri, H. 2015c, "Influence of the inclined edge notches on the shear-fracture behavior in edge-notched beam specimens", Comput. Concrete, 16, 605-623.
  20. Haeri, H., Khaloo, A. and Marji, M.F. (2015a), "Experimental and numerical simulation of the microcrack coalescence mechanism in rock-like materials", Strength Mater., 47(5), 740-754. https://doi.org/10.1007/s11223-015-9711-6
  21. Haeri, H., Khaloo, A. and Marji, M.F. (2015b), "Fracture analyses of different pre-holed concrete specimens under compression", Acta Mech. Sinic., 31(6), 855-870. https://doi.org/10.1007/s10409-015-0436-3
  22. Haeri, H., Khaloo, A. and Marji, M.F. (2015c), "A coupled experimental and numerical simulation of rock slope joints behavior", Arab. J. Geosci., 8(9), 7297-7308. https://doi.org/10.1007/s12517-014-1741-z
  23. Haeri, H., Sarfarazi, V. and Hedayat, A. (2016a), "Suggesting a new testing device for determination of tensile strength of concrete", Struct. Eng. Mech., 60(6), 939-952. https://doi.org/10.12989/sem.2016.60.6.939
  24. Haeri, H., Sarfarazi, V. and Lazemi, H. (2016b), "Experimental study of shear behavior of planar non-persistent joint", Comput. Concrete, 17(5), 639-653. https://doi.org/10.12989/cac.2016.17.5.639
  25. Haeri, H. and Sarfarazi, V. (2016), "The effect of non-persistent joints on sliding direction of rock slopes", Comput. Concrete, 17(6),723-737 https://doi.org/10.12989/cac.2016.17.6.723
  26. Haeri, H., Shahriar, K. and Marji, M.F. (2013), "Modeling the propagation mechanism of two random micro cracks in rock samples under uniform tensile loading,", Proceedings of the ICF13.
  27. Haeri, H., Shahriar, K., Fatehi Marji, M. and Moarefvand, P. (2014), "On the crack propagation analysis of rock like Brazilian disc specimens containing cracks under compressive line loading", Lat. Am. J. Sol. Struct., 11(8), 1400-1416. https://doi.org/10.1590/S1679-78252014000800007
  28. Hoek, E. and Bieniawski, Z.T. (1965), "Brittle fracture propagation in rock under compression", Int. J. Fract., 1(3), 137-155.
  29. Hofmann H., Babadagli T., Yoon J. S., Zang A. and Zimmermann G. (2015), "A grain based modeling study of mineralogical factors affecting strength, elastic behavior and micro fracture development during compression tests in granites", Eng. Fract. Mech., 147, 261-275. https://doi.org/10.1016/j.engfracmech.2015.09.008
  30. Hussian, M.A., Pu, E.L. and Underwood, J.H. (1974), Strain Energy Release Rate for a Crack under Combined Mode I and Mode II. In: Fracture Analysis, ASTM STP 560, American Society for Testing and Materials, 2-28.
  31. Ingraffea, A.R. and Heuze, F.E. (1980), "Finite element models for rock fracture mechanics", Int. J. Numer. Analy. Meth. Geomech., 4(1), 25-43. https://doi.org/10.1002/nag.1610040103
  32. Itasca, C.G. (2002), Users' Manual for Particle Flow Code in 2 Dimensions (PFC2D), Version 3.1, Minneapolis, Minnesota, U.S.A.
  33. Itou, S. (1996), "Dynamic stress intensity factors of two collinear cracks in orthotropic medium subjected to time-harmonic disturbance", Theoret. Appl. Fract. Mech., 25(2), 155-166. https://doi.org/10.1016/0167-8442(96)00018-3
  34. Janeiro, R.P. and Einstein, H.H. (2010), "Experimental study of the cracking behavior of specimens containing inclusions (under uniaxial compression)", Int. J. Fract., 164(1), 83-102. https://doi.org/10.1007/s10704-010-9457-x
  35. Jiang, Z., Wan, S., Zhong, Z., Li, M. and Shen, K. (2014), "Determination of mode-I fracture toughness and nonuniformity for GFRP double cantilever beam specimens with an adhesive layer", Eng. Fract. Mech., 128, 139-156. https://doi.org/10.1016/j.engfracmech.2014.07.011
  36. Jiefan, H., Ganglin, C., Yonghong, Z. and Ren, W. (1990), "An experimental study of the strain field development prior to failure of a marble plate under compression", Tectonophys., 175(1-3), 184-269.
  37. Lajtai, E.Z. (1971), "A theoretical and experimental evaluation of the Griffith theory of brittle fracture", Tectonophys., 11(2), 129-156. https://doi.org/10.1016/0040-1951(71)90060-6
  38. Lajtai, E.Z. (1974), "Brittle fractures in compression", Int. J. Fract., 10(4), 525-536. https://doi.org/10.1007/BF00155255
  39. Lancaster, I.M., Khalid, H.A. and Kougioumtzoglou, I.A. (2013), "Extended FEM modelling of crack propagation using the semicircular bending test", Constr. Build. Mater., 48, 270-277. https://doi.org/10.1016/j.conbuildmat.2013.06.046
  40. Lee, S. and Chang, Y. (2015), "Evaluation of RPV according to alternative fracture toughness requirements", Struct. Eng. Mech., 53(6).
  41. Leonel, E.D., Chateauneuf, A. and Venturini, W.S. (2012), "Probabilistic crack growth analyses using a boundary element model: Applications in linear elastic fracture and fatigue problems", Eng. Analy. Bound. Elem., 36, 944-959. https://doi.org/10.1016/j.enganabound.2011.12.016
  42. Li, S., Wang, H., Li, Y., Li, Q., Zhang, B. and Zhu, H. (2016), "A new mini-grating absolute displacement measuring system for static and dynamic geomechanical model tests", Measure., 82, 421-431.
  43. Li, Y.P., Chen, L.Z. and Wang, Y.H. (2005), "Experimental research on pre-cracked marble under compression", Int. J. Sol. Struct., 42, 2505-2516. https://doi.org/10.1016/j.ijsolstr.2004.09.033
  44. Lin, C.H. and Lin, M.L. (2015), "Evolution of the large landslide induced by Typhoon Morakot: A case study in the Butangbunasi River, Southern Taiwan using the discrete element method", Eng. Geol., 197, 172-187. https://doi.org/10.1016/j.enggeo.2015.08.022
  45. Liu, X., Nie, Z., Wu, S. and Wang, C. (2015), "Self-monitoring application of conductive asphalt concrete under indirect tensile deformation", Case Stud. Constr. Mater., 3, 70-77. https://doi.org/10.1016/j.cscm.2015.07.002
  46. Lu, F.Y., Lin, Y.L., Wang, X.Y., Lu, L. and Chen, R. (2015), "A theoretical analysis about the influence of interfacial friction in SHPB tests", Int. J. Imp. Eng., 79, 95-101.
  47. Miller, J.T. and Einstein, H.H. (2008), "Crack coalescence tests on granite", Proceedings of the 42nd US Rock Mechanics Symposium, San Francisco, U.S.A.
  48. Mobasher, B., Bakhshi, M. and Barsby, C. (2014), "Backcalculation of residual tensile strength of regular and high performance fibre reinforced concrete from flexural tests", Constr. Build. Mater., 70, 243-253. https://doi.org/10.1016/j.conbuildmat.2014.07.037
  49. Mohammad, A. (2016), "Statistical flexural toughness modeling of ultra-high performance mortar using response surface method", Comput. Concrete, 17(4), 33-39.
  50. Mughieda, O. and Alzoubi, A.K. (2004), "Fracture mechanisms of offset rock joints-a laboratory investigation", Geotech. Geol. Eng., 22(4), 545-562. https://doi.org/10.1023/B:GEGE.0000047045.89857.06
  51. Noel, M. and Soudki, K. (2014), "Estimation of the crack width and deformation of FRP-reinforced concrete flexural members with and without transverse shear reinforcement", Eng. Struct., 59, 393-398. https://doi.org/10.1016/j.engstruct.2013.11.005
  52. Oetomo, J.J., Vincens, E., Dedecker, F. and Morel, J.C. (2016), "Modeling the 2D behavior of dry-stone retaining walls by a fully discrete element method", Int. J. Numer. Analy. Meth. Geomech., 40(7), 1099-1120. https://doi.org/10.1002/nag.2480
  53. Oliveira, H.L. and Leonel, E.D. (2014), "An alternative BEM formulation, based on dipoles of stresses and tangent operator technique, applied to cohesive crack growth modeling", Eng. Analy. Bound. Elem., 41, 74-82. https://doi.org/10.1016/j.enganabound.2014.01.002
  54. Ozecebe, G. (2011), "Minimum flexural reinforcement for Tbeams made of higher strength concrete", Can. J. Civil Eng., 26(5), 525-534. https://doi.org/10.1139/l99-013
  55. Pan, B., Gao, Y. and Zhong, Y. (2014), "Theoretical analysis of overlay resisting crack propagation in old cement mortar pavement", Struct. Eng. Mech., 52(4) 167-181.
  56. Park, N.S. (2001), "Crack propagation and coalescence in rock under uniaxial compression", M.Sc. Dissertation, Seoul National University, Korea.
  57. Potyondy, D.O. and Cundall, P.A. (2004), "A bonded-particle model for rock", Int. J. Rock Mech. Min. Sci., 41, 1329-1364.
  58. Rajabi, M., Soltani, N. and Eshraghi, I. (2016), "Effects of temperature dependent material properties on mixed mode crack tip parameters of functionally graded materials", Struct. Eng. Mech., 58(2), 144-156.
  59. Ramadoss, P. and Nagamani, K. (2013), "Stress-strain behavior and toughness of high-performance steel fiber reinforced mortar in compression", Comput. Mortar, 11(2), 55-65.
  60. Reyes, O. and Einstein, H.H. (1991), "Failure mechanisms of fractured rock-a fracture coalescence model", Proceedings of the 7th Congress of the ISRM, Aachen, Germany.
  61. Ruiz, G. and Carmona, R.J. (2006a), "Experimental study on the influence of the shape of the cross-section and the rebar arrangement on the fracture of LRC beams", Mater. Struct., 39(3), 343-352. https://doi.org/10.1007/s11527-005-9006-7
  62. Ruiz, G., Carmona, R.J. and Cendon, D.A. (2006b), "Propagation of a cohesive crack through adherent reinforcement layers", Comput. Meth. Appl. Mech. Eng., 195(52), 7237-7248. https://doi.org/10.1016/j.cma.2005.01.029
  63. Sagong, M. and Bobet, A. (2002), "Coalescence of multiple flaws in a rock-model material in uniaxial compression", Int. J. Rock Mech. Min. Sci., 39(2), 229-241. https://doi.org/10.1016/S1365-1609(02)00027-8
  64. Sardemir, M. (2016), "Empirical modeling of flexural and splitting tensile strengths of concrete containing fly ash by GEP", Comput. Concrete, 17(4), 489-498. https://doi.org/10.12989/cac.2016.17.4.489
  65. Sarfarazi, V. and Haeri, H. (2016), "Effect of number and configuration of bridges on shear properties of sliding surface", J. Min. Sci., 52(2), 245-257. https://doi.org/10.1134/S1062739116020370
  66. Sarfarazi, V. and Haeri, H. (2016c), "A review of experimental and numerical investigations about crack propagation", Comput. Concrete, 18(2), 235-266. https://doi.org/10.12989/cac.2016.18.2.235
  67. Sarfarazi, V. and Shubert, W. (2016b), "Numerical simulation of tensile failure of concrete in direct, flexural, double punch tensile and ring tests", Period. Polyech. Civil Eng., 2, 1-8.
  68. Sarfarazi, V., Faridi, H.R., Haeri, H. and Schubert, W. (2016c), "A new approach for measurement of anisotropic tensile strength of concrete", Adv. Concrete Constr., 3(4), 269-284. https://doi.org/10.12989/ACC.2015.3.4.269
  69. Sarfarazi, V., Ghazvinian, A., Schubert, W., Blumel, M. and Nejati, H.R. (2014), "Numerical simulation of the process of fracture of echelon rock joints", Rock Mech. Rock Eng., 47(4), 1355-1371. https://doi.org/10.1007/s00603-013-0450-3
  70. Sarfarazi, V., Haeri, H. and Khaloo, A. (2016a), "The effect of non-persistent joints on sliding direction of rock slopes", Comput. Concrete, 17(6), 723-737. https://doi.org/10.12989/cac.2016.17.6.723
  71. Shaowei, H., Aiqing, X., Xin, H. and Yangyang, Y. (2016), "Study on fracture characteristics of reinforced concrete wedge splitting tests", Comput. Concrete, 18(3), 337-354. https://doi.org/10.12989/cac.2016.18.3.337
  72. Shen, B. (1995), "The mechanism of fracture coalescence in compression-experimental study and numerical simulation", Eng. Fract. Mech., 51(1), 73-85. https://doi.org/10.1016/0013-7944(94)00201-R
  73. Shen, B. and Stephansson, O. (1994), "Modification of the Gcriterion for crack propagation subjected to compression", Eng. Fract. Mech., 47(2), 177-189. https://doi.org/10.1016/0013-7944(94)90219-4
  74. Shuraim, A.B., Aslam, F., Hussain, R. and Alhozaimy, A. (2016), "Analysis of punching shear in high strength RC panelsexperiments, comparison with codes and FEM results", Comput. Concrete, 17(6), 739-760. https://doi.org/10.12989/cac.2016.17.6.739
  75. Sih, G.C. (1974), "Strain-energy-density factor applied to mixed mode crack problems", Int. J. Fract., 10(3), 305-321. https://doi.org/10.1007/BF00035493
  76. Silling, S.A. (2000), "Reformulation of elasticity theory for discontinuities and long-range forces", J. Phys. Sol., 48(1), 175209.
  77. Silling, S.A. (2017), "Stability of peridynamic correspondence material models and their particle discretizations", Comput. Meth. Appl. Mech. Eng., 322, 42-57. https://doi.org/10.1016/j.cma.2017.03.043
  78. Silva, R.V., Brito, J. and Dhir, R.K. (2015), "Tensil strength behaviour of recycled aggregate concrete", Constr. Build. Mater., 83, 108-118.
  79. Tang, C.A. and Kou, S.Q. (1998), "Crack propagation and coalescence in brittle materials under compression", Eng. Fract. Mech., 61(3-4), 311-324. https://doi.org/10.1016/S0013-7944(98)00067-8
  80. Tang, C.A., Lin, P., Wong, R.H.C. and Chau, K.T. (2001), "Analysis of crack coalescence in rock-like materials containing three flaws-part II: Numerical approach", Int. J. Rock Mech. Min. Sci., 38(7), 925-939. https://doi.org/10.1016/S1365-1609(01)00065-X
  81. Tiang, Y., Shi, S., Jia, K. and Hu, S. (2015), "Mechanical and dynamic properties of high strength concrete modified with lightweight aggregates presaturated polymer emulsion", Constr. Build. Mater., 93, 1151-1156. https://doi.org/10.1016/j.conbuildmat.2015.05.015
  82. Vallejo, L.E. (1987), "The influence of fissures in a stiff clay subjected to direct shear", Geotech., 37(1), 69-82. https://doi.org/10.1680/geot.1987.37.1.69
  83. Vallejo, L.E. (1988), "The brittle and ductile behavior of clay samples containing a crack under mixed mode loading", Theoret. Appl. Fract. Mech., 10(1), 73-78. https://doi.org/10.1016/0167-8442(88)90058-4
  84. Vasarhelyi, B. and Bobet, A. (2000), "Modeling of crack initiation, propagation and coalescence in uniaxial compression", Rock Mech. Rock Eng., 33(2), 119-139. https://doi.org/10.1007/s006030050038
  85. Vesga, L.F., Vallejo, L.E. and Lobo-Guerrero, S. (2008), "DEM analysis of the crack propagation in brittle clays under uniaxial compression tests", Int. J. Numer. Analy. Meth. Geomech., 32(11), 1405-1415. https://doi.org/10.1002/nag.665
  86. Wang, R., Zhao, Y., Chen, Y., Yan, H., Yin, Y.Q., Yao, C.Y. and Zhang, H. (1987), "Experimental and finite simulation of Xshear fractures from a crack in marble", Tectonophys., 144, 141150.
  87. Wang, T., Dai, J.G. and Zheng, J.J. (2015), "Multi-angle truss model for predicting the shear deformation of RC beams with low span-effective depth ratios", Eng. Struct., 91, 85-95.
  88. Wang, X., Zhu, Z., Wang, M., Ying, P., Zhou, L. and Dong, Y. (2017), "Study of rock dynamic fracture toughness by using VB-SCSC specimens under medium-low speed impacts", Eng. Fract. Mech., 181, 52-64.
  89. Wong, L.N.Y. and Einstein, H.H. (2008a), "Crack coalescence in molded gypsum and Carrara marble: Part 1. Macroscopic observations and interpretation", Rock Mech. Rock Eng., 42(3), 475-511. https://doi.org/10.1007/s00603-008-0002-4
  90. Wong, L.N.Y. and Einstein, H.H. (2008b), "Crack coalescence in molded gypsum and Carrara marble: Part 2. Microscopic observations and interpretation", Rock Mech. Rock Eng., 42(3), 513-545. https://doi.org/10.1007/s00603-008-0003-3
  91. Wong, L.N.Y. and Einstein, H.H. (2009), "Systematic evaluation of cracking behavior in specimens containing single flaws under uniaxial compression", Int. J. Rock Mech. Min. Sci., 46(2), 239249.
  92. Wong, R.H.C. and Chau, K.T. (1998), "Crack coalescence in a rock-like material containing two cracks", Int. J. Rock Mech. Min. Sci., 35(2), 147-164. https://doi.org/10.1016/S0148-9062(97)00303-3
  93. Wong, R.H.C., Chau, K.T., Tang, C.A. and Lin, P. (2001), "Analysis of crack coalescence in rock-like materials containing three flaws-part I: Experimental approach", Int. J. Rock Mech. Min. Sci., 38(7), 909-924. https://doi.org/10.1016/S1365-1609(01)00064-8
  94. Wong, R.H.C., Guo, Y.S.H., Liu, L.Q., Liu, P.X. and Ma, S.P. (2008), "Nucleation and growth of anti-wing crack from tips of strike-slip flaw", Proceedings of the 42nd US Rock Mechanics Symposium, San Francisco, U.S.A.
  95. Yang, S.Q. (2015), "An experimental study on fracture coalescence characteristics of brittle sandstone specimens combined various flaws", Geomech. Eng., 8(4), 541-557. https://doi.org/10.12989/gae.2015.8.4.541
  96. Yaylac, M. (2016), "The investigation crack problem through numerical analysis", Struct. Eng. Mech., 57(6).
  97. Yoshihara, H. (2013), "Initiation and propagation fracture toughness of solid wood under the mixed mode I/II condition examined by mixed-mode bending test", Eng. Fract. Mech., 104, 1-15. https://doi.org/10.1016/j.engfracmech.2013.03.023
  98. Zeng, G., Yang, X., Yina, A. and Bai, F. (2014), "Simulation of damage evolution and crack propagation in three-point bending pre-cracked asphalt mixture beam", Constr. Build. Mater., 55, 323-332.
  99. Zhang, Q., Zhu, H.H. and Zhang, L. (2015), "Studying the effect of non-spherical microparticles on Hoek-Brown strength parameter mi using numerical true triaxial compressive tests", Int. J. Numer. Analy. Meth. Geomech., 39(1), 96-114. https://doi.org/10.1002/nag.2310
  100. Zhao, Y., Zhao, G.F. and Jiang, Y. (2013), "Experimental and numerical modelling investigation on fracturing in coal under impact loads", Int. J. Fract., 183(1), 63-80. https://doi.org/10.1007/s10704-013-9876-6
  101. Zhou, M. and Song, E. (2016), "A random virtual crack DEM model for creep behavior of rockfll based on the subcritical crack propagation theory", Acta Geotech., 11(4), 827-847. https://doi.org/10.1007/s11440-016-0446-8
  102. Zhou, X.P., Xia, E.M., Yang, H.Q. and Qian, Q.H. (2012), "Different crack sizes analyzed for surrounding rock mass around underground caverns in Jinping I hydropower station", Theoret. Appl. Fract. Mech., 57(1), 19-30. https://doi.org/10.1016/j.tafmec.2011.12.004
  103. Zhou, X.P. and Yang, H.Q. (2007), "Micromechanical modeling of dynamic compressive responses of mesoscopic heterogenous brittle rock", Theoret. Appl. Fract. Mech., 48(1), 1-20. https://doi.org/10.1016/j.tafmec.2007.04.008
  104. Zhou, X.P., Zhang, Y.X. and Ha, Q.L. (2008), "Real-time computerized tomography (CT) experiments on limestone damage evolution during unloading", Theoret. Appl. Fract. Mech., 50(1), 49-56. https://doi.org/10.1016/j.tafmec.2008.04.005
  105. Zhou, X.P. (2004), "Analysis of the localization of deformation and the complete stress-strain relation for mesoscopic heterogeneous brittle rock under dynamic uniaxial tensile loading", Int. J. Sol. Struct., 41(5/6), 1725-1738. https://doi.org/10.1016/j.ijsolstr.2003.07.007
  106. Zhou, X.P., Ha, Q., Zhang, Y. and Zhu, K. (2004), "Analysis of deformation localization and the complete stress-strain relation for brittle rock subjected to dynamic compressive loads", Int. J. Rock Mech. Min. Sci., 41(2), 311-319. https://doi.org/10.1016/S1365-1609(03)00094-7
  107. Zhou, X.P., Shou, Y.D., Qian, Q.H. and Yu, M.H. (2014), "Threedimensional nonlinear strength criterion for rock-like materials based on the micromechanical method", Int. J. Rock Mech. Min. Sci., 72, 54-60.
  108. Zhou, X.P. and Wang, Y.T. (2016), "Numerical simulation of crack propagation and coalescence in pre-cracked rock-like Brazilian disks using the non-ordinary state-based peridynamics", Int. J. Rock Mech. Min. Sci., 89, 235-249. https://doi.org/10.1016/j.ijrmms.2016.09.010
  109. Zhou, X.P. and Yang, H.Q. (2012), "Multiscale numerical modeling of propagation and coalescence of multiple cracks in rock masses", Int. J. Rock Mech. Min. Sci., 55, 15-27. https://doi.org/10.1016/j.ijrmms.2012.06.001
  110. Zhou, X.P., Bi, J. and Qian, Q.H. (2015), "Numerical simulation of crack growth and coalescence in rock-like materials containing multiple pre-existing flaws", Rock Mech. Rock Eng., 48(3), 1097-1114. https://doi.org/10.1007/s00603-014-0627-4
  111. Zhou, X.P., Gu, X.B. and Wang, Y.T. (2015), "Numerical simulations of propagation, bifurcation and coalescence of cracks in rocks", Int. J. Rock Mech. Min. Sci., 80, 241-254.