DOI QR코드

DOI QR Code

기존/개선 수치 해석 기법을 이용한 계류 체인 링크의 면외 굽힘 강성

Out-Of-Plane Bending Stiffnesses in Offshore Mooring Chain Links Based on Conventional and Advanced Numerical Simulation Techniques

  • 정준모 (인하대학교 조선해양공학과) ;
  • 이재빈 (인하대학교 조선해양공학과) ;
  • 김영훈 (경남대학교 조선해양시스템공학과)
  • Choung, Joonmo (Department of Naval Architecture and Ocean Engineering, Inha University) ;
  • Lee, Jae-bin (Department of Naval Architecture and Ocean Engineering, Inha University) ;
  • Kim, Young Hun (Department of Naval Architecture and Ocean System Engineering, Kyungnam University)
  • 투고 : 2018.06.13
  • 심사 : 2018.10.18
  • 발행 : 2018.10.31

초록

After an accident involving mooring link failures in an offloading buoy, verification of the fatigue safety in terms of the out-of-plane bending (OPB) and in-plane bending (IPB) moments has become a key engineering item in the design of various floating offshore units. The mooring links for an 8 MW floating offshore wind turbine were selected for this study. To identify the OPB stiffness (OPB moment versus interlink angle), a numerical simulation model, called the 3-link model, is usually composed of three successive chain links closest to the fairlead or chain hawse. This paper introduces two numerical simulation techniques for the 3-link analyses. The conventional and advanced approaches are both based on the prescribed rotation approach (PRA) and direct tension approach (DTA). Comparisons of the nominal stress distributions, OPB stiffnesses, hotspot stress curves, and stress concentration curves are presented. The multiple link analyses used to identify the tension angle versus interlink angle require the OPB stiffness data from the 3-link analyses. A convergence study was conducted to determine the minimum number of links for a multi-link analysis. It was proven that 10 links were sufficient for the multi-link analysis. The tension angle versus interlink angle relations are presented based on multi-link analyses with 10 links. It was found that the subsequent results varied significantly according to the 3-link analysis techniques.

키워드

참고문헌

  1. Bureau Veritas(BV), 2014. Fatigue of Top Chain of Mooring Lines due to In-plane and Out-of-plane Bendings: Guidance Note NI 604 DT R00E. BV, France.
  2. Choung, J., Han, S., 2016a. A Novel Procedure for Mooring Chain Fatigue Prediction based on Maximum Principal Stress Considering Out-of-Plane and In-Plane Bending Effects. Journal of the Society of Naval Architects of Korea, 53(3), 237-248. https://doi.org/10.3744/SNAK.2016.53.3.237
  3. Choung, J., Han, S., 2016b. A Novel Approach to Predict Mooring Chain Fatigue Considering Out-of-Plane and In-Plane Bending Effects. Proceedings of 1st International Conference on Ships and Offshore Structures, Hamburg, Germany.
  4. Choung, J., Lee, J., 2018. Study on Prediction of Stresses by Out-of-Plane and In-Plane Bending Moments in Offshore Mooring Chain. Ships and Offshore Structures, 1-15.
  5. Det Norske Veritas(DNV), 2010. Offshore Mooring Chain: Offshore Standard DNV-OS-E302. DNV, Norway.
  6. Jean, P., Goessens, K., L'Hostis, D., 2005. Failure of Chains by Bending on Deepwater Mooring Systems. Proceedings of the Offshore Technology Conference, Houston Texas, USA.
  7. Kim, M., Kim, Y., 2017. Nonlinear Finite Element Analysis for Mooring Chain Considering OPB/IPB. Journal of Ocean Engineering and Technology, 31(4), 299-307. https://doi.org/10.26748/KSOE.2017.08.31.4.299
  8. Li, C.B., Choung, J., Noh, M.H., 2018. Wide-banded Fatigue Damage Evaluation of Catenary Mooring Lines using Various Artificial Neural Networks models. Marine Structures, 60, 186-200. https://doi.org/10.1016/j.marstruc.2018.03.013
  9. Lim, Y., Kim, K., Choung, J., Kang. C., 2010. A Study on Out-of-Plane Bending Mechanism of Mooring Chains for Floating Offshore Plants. Journal of the Society of Naval Architects of Korea, 47(4), 580-588. https://doi.org/10.3744/SNAK.2010.47.4.580
  10. Melis, C., Jean, P., Vargas, P., 2005. Out-of-Plane Bending Testing of Chain Links. Proceedings of 24th International Conference on Offshore Mechanics and Arctic Engineering, Halkidiki, Greece.
  11. Rampi, L., Vargas, P., 2006. Fatigue Testing of Out-of-Plane Bending Mechanism of Chain Links. Proceedings of 25th International Conference on Offshore Mechanics and Arctic Engineering, Hamburg, Germany.
  12. Lee, J.B., Koo, W., Choung, J., 2018, Out-of-Plane Bending Moment-Induced Hotspot Stress Evaluation Using Advanced Numerical Technique. Proceedings of the 37th International Conference on Offshore Mechanics and Arctic Engineering, Madrid, Spain.
  13. Rampi, L., Dewi, F., Vargas, P., 2015. Chain Out of Plane Bending(OPB) Joint Industry Project(JIP) Summary and Main Results. Proceedings of the Offshore Technology Conference, Houston Texas, USA.
  14. Rampi, L., Dewi, F., Francois, M., Gerthoffert, A., Vargas, P., 2016a. Chain out of Plane Bending(OPB) Fatigue Joint Industry Project(JIP) Static Test Program and OPB Interlink Stiffness. Proceedings of the 35th International Conference on Offshore Mechanics and Arctic Engineering, Busan, South Korea.
  15. Rampi, L., Bignonnet, A., Cunff, C.L., Bourgin, F., Vargas, P., 2016b. Chain out of Plane Bending(OPB) Fatigue Joint Industry Project(JIP) Fatigue Test Program Results and Methodology. Proceedings of the 35th International Conference on Offshore Mechanics and Arctic Engineering, Busan, South Korea.