Geomechanics and Engineering

  • 제16권2호
  • /
  • Pages.195-204
  • /
  • 2018
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

The rock fragmentation mechanism and plastic energy dissipation analysis of rock indentation

  • Zhu, Xiaohua (School of Mechatronic Engineering, Southwest Petroleum University) ;
  • Liu, Weiji (School of Mechatronic Engineering, Southwest Petroleum University)
  • 투고 : 2017.08.14
  • 심사 : 2018.06.12
  • 발행 : 2018.10.10
⟨ 이전 논문 다음 논문 ⟩

초록

Based on theories of rock mechanics, rock fragmentation, mechanics of elasto-plasticity, and energy dissipation etc., a method is presented for evaluating the rock fragmentation efficiency by using plastic energy dissipation ratio as an index. Using the presented method, the fragmentation efficiency of rocks with different strengths (corresponding to soft, intermediately hard and hard ones) under indentation is analyzed and compared. The theoretical and numerical simulation analyses are then combined with experimental results to systematically reveal the fragmentation mechanism of rocks under indentation of indenter. The results indicate that the fragmentation efficiency of rocks is higher when the plastic energy dissipation ratio is lower, and hence the drilling efficiency is higher. For the rocks with higher hardness and brittleness, the plastic energy dissipation ratio of the rocks at crush is lower. For rocks with lower hardness and brittleness (such as sandstone), most of the work done by the indenter to the rocks is transferred to the elastic and plastic energy of the rocks. However, most of such work is transferred to the elastic energy when the hardness and the brittleness of the rocks are higher. The plastic deformation is small and little energy is dissipated for brittle crush, and the elastic energy is mainly transferred to the kinetic energy of the rock fragment. The plastic energy ratio is proved to produce more accurate assessment on the fragmentation efficiency of rocks, and the presented method can provide a theoretical basis for the optimization of drill bit and selection of well drilling as well as for the selection of the rock fragmentation ways.

키워드

과제정보

연구 과제 주관 기관 : National Natural Science Foundation of China

참고문헌

  1. Alehossein, H., Detournay, E. and Huang, H. (2000), "An analytical model for the indentation of rocks by blunt tools", Rock Mech. Rock Eng., 33(4), 267-284. https://doi.org/10.1007/s006030070003
  2. Augustine, C.R. (2009), "Hydrothermal spallation drilling and advanced energy conversion technologies for engineered geothermal systems", Ph.D. Dissertation, Massachusetts Institute of Technology, Massachusetts, U.S.A.
  3. Carpinteri, A. and Invernizzi, S. (2005), "Numerical analysis of the cutting interaction between indenters acting on disordered materials", J. Fract., 131(2), 143-154. https://doi.org/10.1007/s10704-004-3635-7
  4. Carpinteri, A., Chiaia, B. and Invernizzi, S. (2004), "Numerical analysis of indentation fracture in quasi-brittle materials", Eng. Fract. Mech., 71(4), 567-577. https://doi.org/10.1016/S0013-7944(03)00037-7
  5. Chen, L.H. and Labuz, J.F. (2006), "Indentation of rock by wedgeshaped tools", J. Rock Mech. Min. Sci., 43(7), 1023-1033.
  6. Chen, L.S., Huang, G.Z. and Chen, Y.C. (2009), "Acoustic emission evolution in indentation fracture of rocks under different lateral pressure free boundaries", Chin. J. Rock Mech. Eng., 28(12), 2411-2420 (in Chinese). https://doi.org/10.3321/j.issn:1000-6915.2009.12.005
  7. Chen, S., Grosz, G., Anderle, S., Arfele, R. and Xun, K. (2015), "The role of rock-chip removals and cutting-area shapes in polycrystalline-diamond-compact-bit design optimization", SPE Drill. Completion, 30(4), 334-347. https://doi.org/10.2118/171833-PA
  8. Detournay, E., Fairhurst, C. and Labuz, J.F. (1995), "A model of tensile failure initiation under an indentor", Proceedings of the 2nd International Conference on Mechanics of Jointed and Faulted Rock (MJFR-S), Vienna, Austria, April.
  9. Gillis, P.J., Gillis, I.G. and Knull, C.J. (2004), Rotational Impact Drill Assembly, U.S. Patent 6,742,609, U.S. Patent and Trademark Office, Washington, D.C., U.S.A.
  10. Han, G. and Bruno, M.S. (2006), "Percussion drilling: From lab tests to dynamic modeling", Proceedings of the International Oil & Gas Conference and Exhibition in China, Beijing, China, December.
  11. Huang, H. (1999), "Discrete element modeling of rock-tool interaction", Ph.D. Dissertation, University of Minnesota, Minnesota, U.S.A.
  12. Huang, H. and Detournay, E. (2013), "Discrete element modeling of tool-rock interaction II: Rock indentation", J. Numer. Anal. Meth. Geomech., 37(13), 1930-1947.
  13. Huang, H., Damjanac, B. and Detournay, E. (1998), "Normal wedge indentation in rocks with lateral confinement", Rock Mech. Rock Eng., 31(2), 81-94. https://doi.org/10.1007/s006030050010
  14. Johnson, K.L. (1970), "The correlation of indentation experiments", J. Mech. Phys. Solids, 18(2), 115-126. https://doi.org/10.1016/0022-5096(70)90029-3
  15. Johnson, K.L. (1987), Contact Mechanics, Cambridge University Press.
  16. Kolle, J.J. (2000), "Coiled-tubing drilling with supercritical carbon dioxide", Proceedings of the SPE/CIM International Conference on Horizontal Well Technology, Calgary, Canada, November.
  17. Kuang, Y.C., Zhu, Z.P. and Jiang, H.J. (2012), "The Experimental study and numerical simulation of single particle impacting rock", Acta Petrolei Sinica, 33(6), 1059-1063 (in Chinese).
  18. Lawn, B. and Wilshaw, R. (1975), "Indentation fracture: principles and applications", J. Mater. Sci., 10(6), 1049-1081. https://doi.org/10.1007/BF00823224
  19. Lawn, B.R. and Evans, A.G. (1977), "A model for crack initiation in elastic/plastic indentation fields", J. Mater. Sci., 12(11), 2195-2199. https://doi.org/10.1007/BF00552240
  20. Lawn, B.R. and Swain, M.V. (1975), "Microfracture beneath point indentations in brittle solids", J. Mater. Sci., 10(1), 113-122. https://doi.org/10.1007/BF00541038
  21. Liu, H.Y., Kou, S.Q., Lindqvist, P.A. and Tang, C.A. (2002), "Numerical simulation of the rock fragmentation process induced by indenters", J. Rock Mech. Min. Sci., 39(4), 491-505.
  22. Marshall, D.B. (1984), "Measurement of dynamic hardness by controlled sharp projectile impact effects in elastic/plastic indentation", Amer. Ceram. Soc., 67(1), 580-585.
  23. Martinez, I.M.R., Fontoura, S., Inoue, N., Carrapatoso, C.M., Lourenco, A. and Curry, D. (2013), "Simulation of single cutter experiments in evaporites through finite element method", Proceedings of the SPE/IADC Drilling Conference and Exhibition, Amsterdam, The Netherlands, March.
  24. Melamed, Y., Kiselev, A., Gelfgat, M., Dreesen, D. and Blacic, J. (2000), "Hydraulic hammer drilling technology: Developments and capabilities", J. Energy Resour. Technol., 122(1), 1-7.
  25. Mendoza, R.J.A. (2013), "Considerations for discrete element modeling of rock cutting", Ph.D. Dissertation, University of Pittsburgh, Pittsburg, Pennsylvania, U.S.A.
  26. Mo, Z.Z., Li, H.B., Zhou, Q.C., Zou, F., Zhu, X.M., Wang, C.B. and Hao, Y.F. (2012), "Experimental study of microscopic deterioration under wedge cutter", Rock Soil Mech., 33(5), 1333-1340 (in Chinese). https://doi.org/10.3969/j.issn.1000-7598.2012.05.009
  27. Ni, H.J., Wang, R.H. and Ge, H.K. (2004), "Numerical simulation on rock fragmentation under high pressure water jet", Chin. J. Rock Mech. Eng., 23(4), 550-554 (in Chinese). https://doi.org/10.3321/j.issn:1000-6915.2004.04.004
  28. Oothoudt, T. (1999), "The benefits of sonic core drilling to the mining industry", Proceedings of the 6th International Conference on Tailings and Mine Waste '99, Fort Collins, Colorado, U.S.A., January.
  29. Paluszny, A., Zimmerman, R.W., Potjewyd, J. and Jarvis, B. (2014), "Finite element-based numerical modeling of fracture propagation due to the plunge of a spherical indenter", Proceedings of the 48th US Rock Mechanics/Geomechanics Symposium, Minneapolis, Minnesota, U.S.A., June.
  30. Rajabov, V., Miska, S.Z., Mortimer, L., Yu, M. and Ozbayoglu, M.E. (2012), "The effects of back rake and side rake angles on mechanical specific energy of single PDC cutters with selected rocks at varying depth of cuts and confining pressures", Proceedings of the IADC/SPE Drilling Conference and Exhibition, San Diego, California, U.S.A., March.
  31. Ren, J.H., Xu, Y.J., Zhao, J., Zhao, X.L. and Zhang, M. (2011), "Numerical simulation analysis of particle impacting breaking rock", Chin. J. High Pressure Phys., 26(1), 89-94 (in Chinese).
  32. Sherrit, S., Bao, X., Chang, Z., Dolgin, B. P., Bar-Cohen, Y., Pal, D., Kroh, J. and Peterson, T. (2000), "Modeling of the ultrasonic/sonic driller/corer: USDC", Proceedings of the 2000 IEEE Ultrasonics Symposium, San Juan, Puerto Rico, October.
  33. Sinha, P. and Gour, A. (2006), "Laser drilling research and application: An update", Proceedings of the SPE/IADC Indian Drilling Technology Conference and Exhibition, Mumbai, India, October.
  34. Souissi, S., Hamdi, E. and Sellami, H. (2015), "Microstructure effect on hard rock damage and fracture during indentation process", Geotech. Geol. Eng., 33(6),1539-1550. https://doi.org/10.1007/s10706-015-9920-6
  35. Swain, M.V. and Hagan, J.T. (1976), "Indentation plasticity and the ensuing fracture of glass", J. Phys. D Appl. Phys., 9(15), 2201. https://doi.org/10.1088/0022-3727/9/15/011
  36. Tan, X.C., Kou, S.Q. and Lindqvist, P.A. (1998), "Application of the DDM and fracture mechanics model on the simulation of rock breakage by mechanical tools", Eng. Geol., 49(3), 277-284. https://doi.org/10.1016/S0013-7952(97)00059-8
  37. Tao, X.H., Zhang, J.L. and Zeng, Y.J. (1998), "Study and application of rotary percussion drilling technology", Oil Drill. Prod. Technol., 20(2), 27-30 (in Chinese).
  38. Teale, R. (1965), "The concept of specific energy in rock drilling", J. Rock Mech. Min. Sci. Geomech. Abstr., 2(1), 57-73. https://doi.org/10.1016/0148-9062(65)90022-7
  39. Wang, S.Y., Sloan, S.W., Liu, H.Y. and Tang, C.A. (2011), "Numerical simulation of the rock fragmentation process induced by two drill bits subjected to static and dynamic (impact) loading", Rock Mech. Rock Eng., 44(3), 317-332. https://doi.org/10.1007/s00603-010-0123-4
  40. Wilkinson, M.A. and Tester, J.W. (1993), "Experimental measurement of surface temperatures during flame-jet induced thermal spallation", Rock Mech. Rock Eng., 26(1), 29-62. https://doi.org/10.1007/BF01019868
  41. Xu, Y.J. (2004), "Basic research on the theory and application of super high pressure water jet", Ph.D. Dissertation, Southwest Petroleum University, Chengdu, China
  42. Xu, Z., Reed, C.B., Leong, K.H., Parker, R.A. and Graves, R.M. (2003), "Application of high powered lasers to perforated completions", Proceedings of the International Congress on Applications of Laser & Electro-Optics, Jacksonville, Florida, U.S.A.
  43. Yin, L.J., Gong, Q.M., Ma, H.S., Zhao, J. and Zhao, X.B. (2014), "Use of indentation tests to study the influence of confining stress on rock fragmentation by a TBM cutter", J. Rock Mech. Min. Sci., 72, 261-276.
  44. Zhang, H. and Song, H. (2013b), "Experimental investigation on deformation and failure of rock under cyclic indentation", Proceedings of the International Conference on Fracture, Beijing, China, June.
  45. Zhang, H., Huang, G., Song, H. and Kang, Y. (2012), "Experimental investigation of deformation and failure mechanisms in rock under indentation by digital image correlation", Eng. Fract. Mech., 96, 667-675. https://doi.org/10.1016/j.engfracmech.2012.09.012
  46. Zhang, H., Song, H., Kang, Y., Huang, G. and Qu, C. (2013a), "Experimental analysis on deformation evolution and crack propagation of rock under cyclic indentation", Rock Mech. Rock Eng., 46(5), 1053-1059. https://doi.org/10.1007/s00603-012-0309-z
  47. Zhou, Y. and Lin, J.S. (2014), "Modeling the ductile-brittle failure mode transition in rock cutting", Eng. Fract. Mech., 127, 135-147. https://doi.org/10.1016/j.engfracmech.2014.05.020
  48. Zhou, Y., Zhang, W., Gamwo, I.K., Lin, J.S., Eastman, H., Whipple, G. and Gill, M. (2012), "Mechanical specific energy versus depth of cut", Proceedings of the 46th US Rock Mechanics/Geomechanics Symposium, Chicago, Illinois. U.S.A., June.
  49. Zhu, X., Liu, W. and He, X. (2017), "The investigation of rock indentation simulation based on discrete element method", KSCE J. Civ. Eng., 21(4), 1201-1212.
  50. Zhu, X., Tang, L. and Tong, H. (2014), "Effects of high-frequency torsional impacts on rock drilling", Rock Mech. Rock Eng., 47(4), 1345-1354. https://doi.org/10.1007/s00603-013-0461-0

피인용 문헌

  1. Comparative Study on Dynamic Mechanical Properties and Energy Dissipation of Rocks under Impact Loads vol.2020, pp.None, 2018, https://doi.org/10.1155/2020/8865099
  2. On the Failure Mechanism of Brittle Granite in 2-D Rock Indentation vol.43, pp.5, 2020, https://doi.org/10.1520/gtj20180413