DOI QR코드

DOI QR Code

Experimental investigation of masonry walls supported by steel plate-masonry composite beams

  • Jing, Deng-Hu (School of Civil Engineering, Southeast University) ;
  • Chen, Jian-Fei (School of Natural and Built Environment, Queen's University Belfast) ;
  • Amato, Giuseppina (School of Natural and Built Environment, Queen's University Belfast) ;
  • Wu, Ting (School of Civil Engineering, Southeast University) ;
  • Cao, Shuang-Yin (School of Civil Engineering, Southeast University)
  • 투고 : 2017.10.02
  • 심사 : 2018.07.15
  • 발행 : 2018.09.25

초록

Masonry walls are sometimes removed in buildings to either make new passages or increase the usable space. This may change the loading paths in the structure, and require new beams to transfer the loads which are carried by the masonry walls that are to be removed. One possible method of creating such new beams is to attach steel plates onto part of the existing walls to form a steel plate-masonry composite (SPMC) beam, leading to a new structure with part of the masonry wall supported by a new SPMC beam. This paper presents an experimental investigation into the interaction between the SPMC beam and the masonry wall above. Five SPMC beams supporting a masonry wall were tested to study the influence of parameters including the height-to-span ratio of the masonry wall, height of the beam and thickness of the steel plates. The test results, including failure mode, load-carrying capacity, load-deflection curves and strain distribution, are presented and discussed. It is found that for developing better arching effect in the masonry wall the ratio of the in-plane flexural stiffness of the masonry wall to the flexural stiffness of the SPMC beam must be between 2.8 and 7.1.

키워드

과제정보

연구 과제 주관 기관 : Natural Science Foundation of Jiangsu Province, National Science Foundation of China (NSFC)

참고문헌

  1. Borri, A., Casadei, P., Castori, G. and Hammond, J. (2009), "Strengthening of brick masonry arches with externally bonded steel reinforced composites", ASCE J. Compos. Constr., 13(6), 468-475. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000030
  2. El-Diasity, M., Okail, H., Kamal, O. and Said, M. (2015), "Structural performance of confined masonry walls retrofitted using ferrocement and GFRP under in-plane cyclic loading", Eng. Struct., 94, 54-69. https://doi.org/10.1016/j.engstruct.2015.03.035
  3. Farooq, S.H., Mohamed, A.E. and Ilyas, M. (2014a), "Seismic in-plane performance of retrofitted masonry walls", KSCE J. Civil Eng., 18(1), 226-237. https://doi.org/10.1007/s12205-014-0120-3
  4. Farooq, S.H., Shahid, I. and Ilyas, M. (2014b), "Seismic performance of masonry strengthened with steel strips", KSCE J. Civ. Eng., 18(7), 2170-2180. https://doi.org/10.1007/s12205-014-0540-0
  5. GB 50003-2011 (2012), Code for design of masonry structures; China Architecture & Building Press, Beijing, China. [In Chinese]
  6. GB/T 228.1-2010 (2010), Metallic materials-tensile testing-part 1: methods of test at room temperature; Standards Press of China, Beijing, China. [In Chinese]
  7. GB/T 50129-2011 (2011), Standard for test method of basic mechanics properties of masonry; China Architecture & Building Press, Beijing, China. [In Chinese]
  8. Guerreiro, J., Proenca, J., Ferreira, J.G. and Gago, A. (2018), "Experimental characterization of in-plane behaviour of old masonry walls strengthened through the addition of CFRP reinforced render", Compos. Part B-Eng., 148, 14-26. https://doi.org/10.1016/j.compositesb.2018.04.045
  9. Hardy, S.J. (2000), "Design of steel lintels supporting masonry walls", Eng. Struct., 22(6), 597-604. https://doi.org/10.1016/S0141-0296(99)00004-8
  10. Hardy, S.J. and Al-Salka, M.A. (1995), "Composite action between steel lintels and masonry walls", Struct. Eng. Review, 7(2), 75-82. https://doi.org/10.1016/0952-5807(95)00010-C
  11. Hossain, M.M., Rahman, M.A. and All, S.S. (2000), "Parametric study of composite action between brickwall and supporting beam", J. Civil Eng., 28(1), 51-67.
  12. Ismail, N., Lazzarini, D.L., Laursen, P.T. and Ingham, J.M. (2015), "Seismic performance of face loaded unreinforced masonry walls retrofitted using post-tensioning", Aust. J. Struct. Eng., 11(3), 243-252.
  13. Jing, D.H. (2017), Experimental Study and Application of Steel Plate-brick Masonry Composite Strengthening Technique, Southeast University Press, Nanjing, Jiangsu, China. [In Chinese]
  14. Jing, D.H., Cao, S.Y. and Zhou, H.T. (2011), "Experimental investigation on Steel-plate-masonry composite column compressive behavior", Adv. Mat. Res., 255-260, 591-595.
  15. Jing, D.H., Cao, S.Y. and Shi, L. (2012), "Flexural behaviour of steel plate-masonry composite beams", Steel Compos. Struct., Int. J., 13(2), 123-137. https://doi.org/10.12989/scs.2012.13.2.123
  16. Jing, D.H., Pan, Y.X. and Chen, Y.L. (2013), "Axial behaviour of MFT stub columns with binding bolts and epoxy adhesive," J. Constr. Steel Res., 86, 115-127. https://doi.org/10.1016/j.jcsr.2013.03.024
  17. Kariou, F.A., Triantafyllou, S.P., Bournas, D.A. and Koutas, L.N. (2018), "Out-of-plane response of masonry walls strengthened using textile-mortar system", Constr. Build. Mater., 165, 769-781. https://doi.org/10.1016/j.conbuildmat.2018.01.026
  18. Konthesingha, K.M.C., Masia, M.J., Petersen, R.B., Mojsilovic, N., Simundic, G. and Page, A.W. (2013), "Static cyclic in-plane shear response of damaged masonry walls retrofitted with NSM FRP strips-An experimental evaluation", Eng. Struct., 50, 126-136. https://doi.org/10.1016/j.engstruct.2012.10.026
  19. Martinelli, E., Perri, F., Sguazzo, C. and Faella, C. (2016), "Cyclic shear-compression tests on masonry walls strengthened with alternative configurations of CFRP strips", Bull. Earthquake Eng., 14(6), 1695-1720. https://doi.org/10.1007/s10518-016-9895-6
  20. Preciado, A., Ramirez-Gaytan, A., Gutierrez, N., Vargas, D., Falcon, J.M. and Ochoa, G. (2018), "Nonlinear earthquake capacity of slender old masonry structures prestressed with steel, FRP and NiTi SMA tendons", Steel Compos. Struct., Int. J., 26(2), 213-226.
  21. Santis, S.D., Casadei, P., Canio, G.D., Felice, G.D., Malena, M., Mongelli, M. and Roselli, I. (2016), "Seismic performance of masonry walls retrofitted with steel reinforced grout", Earthq. Eng. Struct. D., 45(2), 229-251. https://doi.org/10.1002/eqe.2625
  22. Santis, S.D., Roscini, F. and Felice, G. (2018), "Full-scale tests on masonry vaults strengthened with steel reinforced grout", Compos. Part B-Eng., 141, 20-36. https://doi.org/10.1016/j.compositesb.2017.12.023
  23. Smith, B.S., Pradolin, L. and Riddington, J.R. (1982), "Composite design method for masonry walls on steel beams", Can. J. Civil Eng., 9(1), 96-106. https://doi.org/10.1139/l82-010
  24. Soltis, L.A. and Tuan, Y.B. (1980), "Steel supported masonry walls", Eng. J., 17(1), 11-13.
  25. Taghdi, M., Bruneau, M. and Saatcioglu, M. (2000), "Seismic retrofitting of low-rise masonry and concrete walls using steel strips", ASCE J. Struct. Eng., 126(9), 1017-1025. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:9(1017)
  26. Wang, X., Lam, C.C. and Iu, V.P. (2018), "Experimental investigation of in-plane shear behaviour of grey clay brick masonry panels strengthened with SRG", Eng. Struct., 162, 84-96. https://doi.org/10.1016/j.engstruct.2018.02.027