DOI QR코드

DOI QR Code

Effective torsional strength of axially restricted RC beams

  • Taborda, Catia S.B. (Department of Civil Engineering and Architecture, Centre of Materials and Building Technologies (C-Made), University of Beira Interior) ;
  • Bernardo, Luis F.A. (Department of Civil Engineering and Architecture, Centre of Materials and Building Technologies (C-Made), University of Beira Interior) ;
  • Gama, Jorge M.R. (Department of Mathematics, Center of Mathematics and Applications, University of Beira Interior)
  • 투고 : 2017.08.29
  • 심사 : 2018.05.28
  • 발행 : 2018.09.10

초록

In a previous study, design charts where proposed to help the torsional design of axially restricted reinforced concrete (RC) beams with squared cross section. In this article, new design charts are proposed to cover RC beams with rectangular cross section. The influence of the height to width ratio of the cross section on the behavior of RC beams under torsion is firstly shown by using theoretical and experimental results. Next, the effective torsional strength of a reference RC beam is computed for several values and combinations of the study variables, namely: height to width ratio of the cross section, concrete compressive strength, torsional reinforcement ratio and level of the axial restraint. To compute the torsional strength, the modified Variable Angle Truss Model for axially restricted RC beams is used. Then, an extensive parametric analysis based on multivariable and nonlinear correlation analysis is performed to obtain nonlinear regression equations which allow to build the new design charts. These charts allow to correct the torsional strength in order to consider the favourable influence of the compressive axial stress that arises from the axial restraint.

키워드

참고문헌

  1. Ali, M.A. and White, R.N. (1999), "Toward a rational approach for design of minimum torsion reinforcement", J. Am. Concrete Inst., 96(1), 40-45.
  2. Belarbi, A. and Hsu, T.C. (1994), "Constitutive laws of concrete in tension and reinforcing bars stiffened by concrete", Struct. J. Am. Concrete Inst., 91(4), 465-474.
  3. Bernardo L.F.A. and Lopes, S.M.R. (2009), "Torsion in HSC hollow beams: Strength and ductility analysis", ACI Struct. J., 106(1), 39-48.
  4. Bernardo, L.F.A., Andrade, J.M.A. and Lopes, S.M.R. (2012), "Softened truss model for reinforced NSC and HSC beams under torsion: A comparative study", Eng. Struct., 42, 278-296. https://doi.org/10.1016/j.engstruct.2012.04.036
  5. Bernardo, L.F.A., Taborda, C.S.B. and Gama, J.M.R. (2015a), "Parametric analysis and torsion design charts for axially restricted RC beams", Struct. Eng. Mech., 55(1), 1-27. https://doi.org/10.12989/sem.2015.55.1.001
  6. Bernardo, L.F.A., Taborda, C.S.B. and Andrade, J.M.A. (2015b), "Ultimate torsional behavior of axially restricted RC beams", Comput. Concrete, 16(1), 67-97. https://doi.org/10.12989/cac.2015.16.1.067
  7. Chen, S., Ye, Y., Guo, Q., Cheng, S. and Diao, B. (2016), "Nonlinear model to predict the torsional response of U-shaped thin-walled RC members", Struct. Eng. Mech., 60(6), 1039-1061. https://doi.org/10.12989/sem.2016.60.6.1039
  8. Chiu, H.J., Fang, I.K., Young, W.T. and Shiau J.K. (2007), "Behavior of reinforced concrete beams with minimum torsional reinforcement", Eng. Struct., 29(9), 2193-2205. https://doi.org/10.1016/j.engstruct.2006.11.004
  9. Fang, I.K. and Shiau, J.K. (2004), "Torsional behavior of normal and high-stregth concrete beams", ACI Struct. J., 101(3), 304-313.
  10. CEB-FIP MODEL CODE (2010), Comite Euro-International du Beton, Suisse.
  11. Gomes, D.P. (2011), "Flexural strength of reinforced concrete beams axially restricted", M.Sc. Dissertation, University of Coimbra, Coimbra, Portugal.
  12. Hsu, T.T. (1968), Torsion of Structural Concrete-Behavior of Reinforced Concrete Rectangular Members, Torsion of Structural Concrete, SP-18, American Concrete Institute, Detroit, 261-306.
  13. Hsu, T.T.C. (1984), Torsion of Reinforced Concrete, Van Nostrand Reinhold Company.
  14. Hsu, T.T.C. and Mo, Y.L. (1985a), "Softening of concrete in torsional members-theory and tests", J. Am. Concrete Inst., 82(3), 290-303.
  15. Hsu T.T.C. and Mo, Y.L. (1985b), "Softening of concrete in torsional members-prestressed concrete", J. Am. Concrete Inst., 82(5), 603-615.
  16. Jeng, C.H. (2015), "Unified softened membrane model for torsion in hollow and solid reinforced concrete members-modeling the entire pre- and post-cracking behavior", J. Struct. Eng., 141(10).
  17. Jeng, C.H., Peng, X. and Wong, Y.L. (2011), "Strain gradient effect in RC elements subjected to torsion", Mag. Concrete Res., 63(5), 343-356. https://doi.org/10.1680/macr.9.00218
  18. Jeng, C.H., Chiu, H.J. and Peng, S.F. (2013), "Design formulas for cracking torque and twist in hollow reinforced concrete members", ACI Struct. J., 110(3), 457-468.
  19. Koutchoukali, N.E. and Belarbi, A. (2001), "Torsion of highstrength reinforced concrete beams and minimum reinforcement requirement", ACI Struct. J., 98(4), 462-469.
  20. Khagehhosseini, A.H., Porhosseini, R., Morshed, R. and Eslami, A. (2013), "An experimental and numerical investigation on the effect of longitudinal reinforcements in torsional resistance of RC beams", Struct. Eng. Mech., 47(2), 247-263. https://doi.org/10.12989/sem.2013.47.2.247
  21. Lando, M. (1987), "Torsion of closed cross-section thin-walled beams: The influence of shearing strain", Thin-Wall. Struct., 5(4), 277-305. https://doi.org/10.1016/0263-8231(87)90008-5
  22. Lampert, P. and Thurlimann, B. (1969), Torsions-Beige-Versuche an Stanhlbetobalken (Torsion Tests of Reinforced Concrete Beams), Bericht, No. 6506-2, Institute fur Baustatik, ETH, Zurich, Swiss.
  23. Leonhardt, F. and Schelling, G. (1974), Torsionsversuche an Stahl Betonbalken, Bulletin No. 239, Dreurscher Ausschuss Fur Stahlbeton, Berlin, Germany.
  24. Levenberg, K. (1944), "A method for the solution of certain nonlinear problems in least squares", Quarter. Appl. Math., 2, 164-168. https://doi.org/10.1090/qam/10666
  25. Lou, T., Lopes, A. and Lopes, S. (2011), "Numerical behaviour of axially restricted RC beams", Proceedings of the International Conference on Recent Advances in Nonlinear Models-Structural Concrete Applications.
  26. Marquardt, D.W. (1963), "An algorithm for least-squares estimation of nonlinear parameters", SIAM J. Appl. Math., 11(2), 431-441. https://doi.org/10.1137/0111030
  27. McMullen, A.E. and Rangan, B.V. (1978), "Pure torsion in rectangular sections: A re-examination", J. Am. Concrete Inst., 75(10), 511-519.
  28. Mondal, T.G. and Prakash, S.S. (2015), "Effect of tension stiffening on the behaviour of square RC column under torsion", Struct. Eng. Mech., 54(3), 2131-2134.
  29. Murín, J. and Kutiš, V. (2008), "An effective finite element for torsion of constant cross-sections including warping with secondary torsion moment deformation effect", Eng. Struct., 30(10), 2716-2723. https://doi.org/10.1016/j.engstruct.2008.03.004
  30. Nash, J.C. (1990), Compact Numerical Methods for Computers. Linear Algebra and Function Minimisation, 2nd Edition, Adam Hilger, Bristol and New York.
  31. NP EN 1992-1-1 (2010), Eurocode 2: Design of Concrete Structures-Part 1: General Rules and Rules for Buildings.
  32. Peng, X.N. and Wong, Y.L. (2011), "Behavior of reinforced concrete walls subjected to monotonic pure torsion-an experimental study", Eng. Struct., 33(9), 2495-2508. https://doi.org/10.1016/j.engstruct.2011.04.022
  33. Rasmussen, L.J. and Baker, G. (1995), "Torsion in reinforced normal and high-strength concrete beams-part 1: Experimental test series", J. Am. Concrete Inst., 92(1), 56-62.
  34. Valipour, H.R. and Foster, S.J. (2010), "Nonlinear analysis of 3D reinforced concrete frames: Effect of section torsion on the global response", Struct. Eng. Mech., 36(4), 421-445. https://doi.org/10.12989/sem.2010.36.4.421
  35. Waldren, P. (1988), "The significance of warping torsion in the design of straight concrete box girder bridges", Can. J. Civil Eng., 15(5), 879-889. https://doi.org/10.1139/l88-113
  36. Wang, Q., Qiu, W. and Zhang, Z. (2015), "Torsion strength of single-box multi-cell concrete box girder subjected to combined action of shear and torsion", Struct. Eng. Mech., 55(5), 953-964. https://doi.org/10.12989/sem.2015.55.5.953
  37. Zhang, L.X. and Hsu, T.C. (1998), "Behavior and analysis of 100 MPa concrete membrane elements", J. Struct. Eng., 124(1), 24-34. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:1(24)

피인용 문헌

  1. A unified approach to shear and torsion in reinforced concrete vol.77, pp.5, 2021, https://doi.org/10.12989/sem.2021.77.5.691