Computers and Concrete

  • 제22권1호
  • /
  • Pages.93-100
  • /
  • 2018
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Effect of thermal-induced microcracks on the failure mechanism of rock specimens

  • Khodayar, Amin (Rock Mechanics Division, School of Engineering, Tarbiat Modares University) ;
  • Nejati, Hamid Reza (Rock Mechanics Division, School of Engineering, Tarbiat Modares University)
  • 투고 : 2017.11.18
  • 심사 : 2018.05.04
  • 발행 : 2018.07.25
⟨ 이전 논문 다음 논문 ⟩

초록

It is seldom possible that geotechnical materials like rocks and concretes found without joints, cracks, or discontinuities. Thereby, the impact of micro-cracks on the mechanical properties of them is to be considered. In the present study, the effect of micro-crack on the failure mechanism of rock specimens under uniaxial compression was investigated experimentally. For this purpose, thermal stress was used to induce micro-cracks in the specimens. Several cylindrical and disk shape specimens were drilled from granite collected from Zanjan granite mine, Iran. Some of the prepared specimens were kept in room temperature and the others were heated by a laboratory furnace to different temperature levels (200, 400, 600, 800 and 1000 degree Celsius). During the experimental tests, Acoustic Emission (AE) sensors were used to monitor specimen failure at the different loading sequences. Also, Scanning Electron Microscope (SEM) was used to distinguish the induced micro-crack by heating in the specimens. The fractographic analysis revealed that the thin sections heated to $800^{\circ}C$ and $1000^{\circ}C$ contain some induced micro-fractures, but in the thin sections heated to $200^{\circ}C$, $400^{\circ}C$ and $600^{\circ}C$ have not been observed any micro-fracture. In the next, a comprehensive experimental investigation was made to evaluate mechanical properties of heated and unheated specimens. Results of experimental tests showed that induced micro-cracks significantly influence on the failure mode of specimens. The specimens kept at room temperature failed in the splitting mode, while the failure mode of specimens heated to $800^{\circ}C$ are shearing and the specimens heated to $1000^{\circ}C$ failed in the spalling mode. On the basis of AE monitoring, it is found that with increasing of the micro-crack density, the ratio of the number of shear cracks to the number of tensile cracks increases, under loading sequences.

키워드

참고문헌

  1. Aggelis, D.G., Mpalaskas, A.C. and Matikas, T.E. (2013), "Acoustic signature of different fracture modes in marble and cementitious materials under flexural load", Mech. Res. Commun., 47, 39-43. https://doi.org/10.1016/j.mechrescom.2012.11.007
  2. Aggelis, D.G., Soulioti, D.V., Sapouridis, N., Barkoula, N.M., Paipetis, A.S. and Matikas, T.E. (2011), "Acoustic emission characterization of the fracture process in fibre reinforced concrete", Constr. Build. Mater., 25, 4126-4131. https://doi.org/10.1016/j.conbuildmat.2011.04.049
  3. Altindag, R. (2000), "The role of rock brittleness on analysis of percussive drilling performance", Proceedings of the 5th National Rock Mech. Symposium, Turkey. (in Turkish)
  4. Andreev, G.E. (1995), Brittle Failure of Rock Materials: Test Results and Constitutive Models, Rotterdam, Brookfield, AA Balkema.
  5. Antonaci, P., Bocca, P. and Masera, D. (2012), "Fatigue crack propagation monitoring by Acoustic Emission signal analysis", Eng. Fract. Mech., 81, 26-32 https://doi.org/10.1016/j.engfracmech.2011.09.017
  6. Batzle, M., Simmons, G. and Siefried, R. (1980), "Micro-crack closure in rocks under stress: direct observation", J. Geophys. Res., 85(B12), 7072-90. https://doi.org/10.1029/JB085iB12p07072
  7. Bieniawski, Z.T. (1967), "Mechanism of brittle fracture of rock. Part II-experimental studies", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 4(4), 407-23. https://doi.org/10.1016/0148-9062(67)90031-9
  8. Blindheim, O.T. and Bruland, A. (1998), "Boreability testing. Norwegian TBM tunnelling 30 years of Experience with TBMs in Norwegian Tunnelling", Norwegian Soil Rock Eng. Assoc., 11, 29-34.
  9. Bobet, A. and Einstein, H.H. (1998), "Fracture coalescence in rock type materials under uniaxial and biaxial", Int. J. Rock Mech. Min. Sci., 35(7), 863-888. https://doi.org/10.1016/S0148-9062(98)00005-9
  10. Cai, M. and Liu, D. (2009), "Study of failure mechanisms of rock under compressive-shear loading using real-time laser holography", Int. J. Rock Mech. Min. Sci., 46, 59-68 https://doi.org/10.1016/j.ijrmms.2008.03.010
  11. Cai, M., He, M. and Liu, D. (2002), Rock Mechanics and Engineering, Science Press, Beijing.
  12. Chen, Y.L., Ni, J., Shao, W., Zhou, Y.C., Javadi, A. and Azzam, R. (2011), "Coalescence of fractures under uni-axial compression and fatigue loading", Rock Mech. Rock Eng., 45(2), 241-249. https://doi.org/10.1007/s00603-011-0186-x
  13. Fakhimi, A. and Hemami, B. (2015), "Axial splitting of rocks under uniaxial compression", Int. J. Rock Mech. Min. Sci., 79, 124-134. https://doi.org/10.1016/j.ijrmms.2015.08.013
  14. Ghazvinian, A., Nejati, H.R., Sarfarazi, V. and Hadei, M.R. (2013), "Mixed mode crack propagation in low brittle rock-like materials", Arab. J. Geosci., 6(11), 4435-4444. https://doi.org/10.1007/s12517-012-0681-8
  15. Gramberg, J. (1989), A Non-conventional View on Rock Mechanics, Balkema, Rotterdam.
  16. Gutenberg, B. and Richte, C. (1949), Seismicity of the Earth and Associated Phenomena, Princeton University Press.
  17. Hallbauer, D., Wagner, H. and Cook, N. (1973), "Some observations concerning the microscopic and mechanical behavior of quartzite specimens in stiff, triaxial compression tests", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 10(6), 713-26. https://doi.org/10.1016/0148-9062(73)90015-6
  18. Hoek, E. and Bieniawski, Z.T. (1965), "Brittle fracture propagation under compression", Int. J. Fract. Mech., 1, 137-55.
  19. Hucka, V. and Das, B. (1974), "Brittleness determination of rocks by different methods", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 1, 389-392.
  20. Hudyma, N., Avar, B.B. and Karakouzian, M. (2004), "Compressive strength and failure modes of lithophysae-rich Topopah Spring Tuff specimens and analog models containing cavities", Eng. Geol., 73(1), 179-190. https://doi.org/10.1016/j.enggeo.2004.01.003
  21. Imani, M., Nejati, H.R. and Goshtasbi, K. (2017), "Dynamic response and failure mechanism of Brazilian disk specimens at high strain rate", Soil Dyn. Earthq. Eng., 100, 261-269. https://doi.org/10.1016/j.soildyn.2017.06.007
  22. ISRM (1981), Suggested Methods: Rock Characterization, Testing and Monitoring, Ed. Brown, E.T., Pergamon, Oxford.
  23. Jaeger, J.C., Cook, N.G.W. and Zimmerman, R.W. (2007), Fundamentals of Rock Mechanics, 4th Edition, Blackwell, Oxford.
  24. Kurz, J.H., Finck, F., Grosse, C.U. and Reinhardt, H.W. (2005), "Stress drop and stress redistribution in concrete quantified over time by the "b-value" analysis", Struct. Hlth. Monit, 5, 69-8.
  25. Lee, S.E. and Jeong, G.C. (2015), "Numerical analysis on microdamage in bisphere model of granitic rock", Geosci. J., 19(1), 135-144. https://doi.org/10.1007/s12303-014-0055-1
  26. Li, Y.P., Chen, L.Z. and Wang, Y.H. (2005), "Experimental research on pre-Cracked marble", Int. J. Solid. Struct., 42, 2505-16. https://doi.org/10.1016/j.ijsolstr.2004.09.033
  27. Meng, F., Zhou, H., Zhang, C., Xu, R. and Lu, J. (2015), "Evaluation methodology of brittleness of rock based on postpeak stress-strain curves", Rock Mech. Rock Eng., 48(5), 1787-1805. https://doi.org/10.1007/s00603-014-0694-6
  28. Moore, D.E. and Lockner, D.A. (1995), "The role of microcracking in shearfracture propagation in granite", J. Struct. Geol., 17, 95-114 https://doi.org/10.1016/0191-8141(94)E0018-T
  29. Mughieda, O.S. and Khawaldeh, I. (2006), "Coalescence of offset rock joints under biaxial loading", Geotech. Geolog. Eng., 24, 985-999. https://doi.org/10.1007/s10706-005-8352-0
  30. Najigivi, A., Nazerigivi, A. and Nejati, H.R. (2017), "Contribution of steel fiber as reinforcement to the properties of cement-based concrete: A review", Comput. Concrete, 20(2), 155-164. https://doi.org/10.12989/CAC.2017.20.2.155
  31. Nasseri, M.H.B., Mohanty, B. and Young, R.P. (2006), "Fracture toughness measurements and acoustic emission activity in brittle rocks", Pure Appl. Geophys., 163, 917-945 https://doi.org/10.1007/s00024-006-0064-8
  32. Nazerigivi, A., Nejati, H.R., Ghazvinian, A. and Najigivi, A. (2017), "Influence of nano-silica on the failure mechanism of concrete specimens", Comput. Concrete, 19(4), 429-434. https://doi.org/10.12989/cac.2017.19.4.429
  33. Nejati, H.R. and Ghazvinian, A. (2014), "Brittleness effect on rock fatigue damage evolution", Rock Mech. Rock Eng., 47(5), 1839-1848. https://doi.org/10.1007/s00603-013-0486-4
  34. Nejati, H.R. and Moosavi, S.A. (2017), "A new brittleness index for estimation of rock fracture toughness", J. Min. Environ., 8(1), 83-91
  35. Pan, P.Z., Feng, X.T. and Hudson, J.A. (2012), "The influence of the intermediate principal stress on rock failure behaviour: a numerical study", Eng. Geol., 124, 109-118. https://doi.org/10.1016/j.enggeo.2011.10.008
  36. Park, C.H. and Bobet, A. (2009), "Crack coalescence in specimens with open and closed flaws: A comparison", Int. J. Rock Mech. Min. Sci., 46, 819-829 https://doi.org/10.1016/j.ijrmms.2009.02.006
  37. Peng, G., Nakamura, S., Zhu, X., Wu, Q. and Wang, H. (2017), "An experimental and numerical study on temperature gradient and thermal stress of CFST truss girders under solar radiation", Comput. Concrete, 20(5), 605-616. https://doi.org/10.12989/CAC.2017.20.5.605
  38. Protodyakonov, M.M. (1963), "Mechanical properties and drillability of rocks", Proceedings of the 5th Symposium Rock Mechanics, University of Minnesota, 103-118.
  39. Pu, C.Z. and Ping, C.A.O. (2012), "Failure characteristics and its influencing factors of rock-like material with multi-fissures under uniaxial compression", Tran. Nonfer. Metal. Soc. China, 22(1), 185-191. https://doi.org/10.1016/S1003-6326(11)61159-X
  40. Ramulu, M. and Kobayashi, A.S. (1985) "Mechanics of crack curving and branching-a dynamic fracture analysis", Int. J. Fract., 27, 187-201. https://doi.org/10.1007/BF00017967
  41. Ren, X., Chen, J., Li, J., Slawson, T.R. and Roth, M.J. (2011). "Micro-cracks informed damage models for brittle solids", Int. J. Solid. Struct., 48, 1560-1571. https://doi.org/10.1016/j.ijsolstr.2011.02.001
  42. Sagong, M. and Bobet, A. (2002), "Coalescence of multiple flaws in a rock-model material in uniaxial compression", Int. J. Rock Mech. Min. Sci., 39, 229-241. https://doi.org/10.1016/S1365-1609(02)00027-8
  43. Shah, S.G. and Kishen, J.M.C. (2012), "Use of acoustic emissions in flexural fatigue crack growth studies on concrete", Eng. Fract. Mech., 87, 36-47. https://doi.org/10.1016/j.engfracmech.2012.03.001
  44. Shao, S., Ranjith, P.G., Wasantha, P.L.P. and Chen, B.K. (2015), "Experimental and numerical studies on the mechanical behaviour of Australian Strathbogie granite at high temperatures: an application to geothermal energy", Geotherm., 54, 96-108. https://doi.org/10.1016/j.geothermics.2014.11.005
  45. She, W., Zhao, G., Yang, G., Jiang, J., Cao, X. and Du, Y. (2016), "Numerical analysis of the thermal behaviors of cellular concrete", Comput. Concrete, 18(3), 319-336. https://doi.org/10.12989/cac.2016.18.3.319
  46. Shen, B. (1995), "The mechanism of fracture coalescence in compression-experimental study and numerical simulation", Eng. Fract. Mech., 51(1), 73-85. https://doi.org/10.1016/0013-7944(94)00201-R
  47. Sprunt, E. and Brace, W. (1974), "Direct observation of microcavities in crystalline rocks", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 11(4),139-50. https://doi.org/10.1016/0148-9062(74)92874-5
  48. Szwedzicki, T. (2007), "A hypothesis on modes of failure of rock samples tested in uniaxial compression", Rock Mech. Rock Eng., 40(1), 97-104. https://doi.org/10.1007/s00603-006-0096-5
  49. Szwedzicki, T. and Shamu, W. (1999), "The effect of material discontinuities on strength of rocksamples", Proc. Austral. Inst. Min. Metall., 304(1), 23-28
  50. Wawersik, W. and Fairhurst, C. (1970), "A study of brittle rock fracture in laboratory compression experiments", Int. J. Rock Mech. Min. Sci. Geomech. Abstr., 7, 561-75. https://doi.org/10.1016/0148-9062(70)90007-0
  51. Wong, R.H.C. and Chau, K.T. (1998), "Crack coalescence in a rock-like material containing two cracks", Int. J. Rock Mech. Min. Sci., 35(2), 147-164. https://doi.org/10.1016/S0148-9062(97)00303-3
  52. Young, R.P. and Martin, C.D. (1993), "Potential role of acoustic emission/ microseismicity investigations in the site characterization and performance monitoring of nuclear waste repositories", Int. J. Rock Mech. Min. Sci., 30, 797-803 https://doi.org/10.1016/0148-9062(93)90025-9
  53. Zhang, C., Zhou, W., Ma, G., Hu, C. and Li, S. (2015), "A mesoscale approach to modeling thermal cracking of concrete induced by water-cooling pipes", Comput. Concrete, 15, 485-501. https://doi.org/10.12989/cac.2015.15.4.485
  54. Zhu, W.C. and Tang, C.A. (2006) "Numerical simulation of Brazilian disk rock failure under static and dynamic loading", Int. J. Rock Mech. Min. Sci., 43, 236-252. https://doi.org/10.1016/j.ijrmms.2005.06.008
  55. Zietlow, W.K. and Labuz, J.F. (1998), "Measurement of the intrinsic process zone in rock using acoustic emission", Int. J. R. Mech. Min. Sci., 3, 291-299.

피인용 문헌

  1. Influence of heating/cooling cycles on the micro/macrocracking characteristics of Rucheng granite under unconfined compression vol.79, pp.3, 2020, https://doi.org/10.1007/s10064-019-01638-4
  2. The Influence of Regional Freeze-Thaw Cycles on Loess Landslides: Analysis of Strength Deterioration of Loess with Changes in Pore Structure vol.12, pp.11, 2020, https://doi.org/10.3390/w12113047