Steel and Composite Structures

  • 제28권1호
  • /
  • Pages.73-82
  • /
  • 2018
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Experimental investigation on shear capacity of partially prefabricated steel reinforced concrete columns

  • Yang, Yong (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Chen, Yang (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Zhang, Jintao (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Xue, Yicong (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Liu, Ruyue (School of Civil Engineering, Xi'an University of Architecture & Technology) ;
  • Yu, Yunlong (School of Civil Engineering, Xi'an University of Architecture & Technology)
  • 투고 : 2017.11.08
  • 심사 : 2018.04.23
  • 발행 : 2018.07.10
⟨ 이전 논문 다음 논문 ⟩

초록

This paper experimentally and analytically elucidates the shear behavior and shear bearing capacity of partially prefabricated steel reinforced concrete (PPSRC) columns and hollow partially prefabricated steel reinforced concrete (HPSRC) columns. Seven specimens including five PPSRC column specimens and two HPSRC column specimens were tested under static monotonic loading. In the test, the influences of shear span aspect ratio and difference of cast-in-place concrete strength on the shear behavior of PPSRC and HPSRC columns were investigated. Based on the test results, the failure pattern, the load-displacement behavior and the shear capacity were focused and analyzed. The test results demonstrated that all the column specimens failed in shear failure mode with high bearing capacity and good deformability. Smaller shear span aspect ratio and higher strength of inner concrete resulted in higher shear bearing capacity, with more ductile and better deformability. Furthermore, calculation formula for predicting the ultimate shear capacity of the PPSRC and HPSRC columns were proposed on the basis of the experimental results.

키워드

과제정보

연구 과제 주관 기관 : National Natural Science Foundation of China, Xi'an University of Architecture and Technology

참고문헌

  1. ACI318 (2011), Building code requirements for structural concrete and commentary; American Concrete Institute; Farmington Hill, MI, USA.
  2. Agheshlui, H., Goldsworthy, H., Gad, E. and Mirza, O. (2017), "Anchored blind bolted composite connection to a concrete filled steel tubular column", Steel Compos. Struct., Int. J., 23(1), 115-130. https://doi.org/10.12989/scs.2017.23.1.115
  3. AIJ (1998), Calculation standard and explication of steel reinforced concrete structures; Architectural Institute of Japan, Atomic Energy Press. [Translated by N.Q. Feng, L.P. Ye, in Chinese]
  4. Albegmprli, H.M.A., Cevik, A., Gulsan, M.E. and Kurtoglu, A.E. (2015), "Reliability analysis of reinforced concrete haunched beams shear capacity based on stochastic nonlinear fe analysis", Comput. Concrete, Int. J., 15(2), 259-277. https://doi.org/10.12989/cac.2015.15.2.259
  5. Chen, C.C. and Lin, N.J. (2006), "Analytical model for predicting axial capacity and behavior of concrete encased steel composite stub columns", J. Constr. Steel Res., 62(5), 424-433. https://doi.org/10.1016/j.jcsr.2005.04.021
  6. Chen, G.W. and Nielsen, M.P. (1988), Plastic analysis of shear in beams, deep beams and corbels, Technical University of Denmark (DTU), BYG-Rapport; No. R-237, Kongens Lyngby, Denmark.
  7. Chen, S. and Wu, P. (2017), "Analytical model for predicting axial compressive behavior of steel reinforced concrete column", J. Constr. Steel Res., 128, 649-660. https://doi.org/10.1016/j.jcsr.2016.10.001
  8. Collins, M.P. and Mitchell, D. (1986), "Rational approach to shear design-the 1984 Canadian code provisions", J. Neurosci. Official J. Soc. Neurosci., 83(6), 925-933.
  9. GB/T 700-2006 (2006), Carbon structure steels; China Planning Press, Beijing, China.
  10. GB/T 50081-2010 (2010), Standard for test method of mechanical properties on ordinary concrete; China Planning Press, Beijing, China.
  11. GB/T 50010-2010 (2010), Code for design of concrete structures; China Architecture and Building Press, Beijing, China.
  12. Hajjar, J.F. (2002), "Composite steel and concrete structural systems for seismic engineering", J. Constr. Steel Res., 58(5), 703-723. https://doi.org/10.1016/S0143-974X(01)00093-1
  13. Hwang, J.H., Lee, D.H., Oh, J.Y., Choi, S.H., Kang, S.K. and Seo, S.Y. (2016), "Seismic performances of centrifugally-formed hollow-core precast columns with multi-interlocking spirals", Steel Compos. Struct., Int. J., 20(6), 1259-1274. https://doi.org/10.12989/scs.2016.20.6.1259
  14. Jaillon, L. and Poon, C.S. (2010), "Design issues of using prefabrication in Hong Kong building construction", Construct. Manag. Econ., 28(10), 1025-1042. https://doi.org/10.1080/01446193.2010.498481
  15. JGJ138 (2016), Code for design of composite structures; China Building Industry Press, Beijing, China.
  16. Kang, L., Leon, R.T. and Lu, X. (2015), "Shear strength analyses of internal diaphragm connections to CFT columns", Steel Compos. Struct., Int. J., 18(5), 1083-1101. https://doi.org/10.12989/scs.2015.18.5.1083
  17. Karimi, K., El-Dakhakhni, W.W. and Tait, M.J. (2012), "Behavior of slender steel-concrete composite columns wrapped with FRP jackets", J. Perform. Constr. Facil., 26(5), 590-599. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000280
  18. Nielsen, M.P. (2011), Limit Analysis and Concrete Plasticity, Rnford Onr.
  19. Pan, Z.F. and Li, B. (2013), "Truss-arch model for shear strength of shear-critical reinforced concrete columns", J. Struct. Eng., 139(4), 548-560. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000677
  20. Pereira, M.F., Nardin, S.D. and Debs, A.L.H.C.E. (2016), "Structural behavior of partially encased composite columns under axial loads", Steel Compos. Struct., Int. J., 20(6), 1305-1322. https://doi.org/10.12989/scs.2016.20.6.1305
  21. Priestley, M.J.N., Verma, R. and Xiao, Y. (1994), "Seismic shear strength of reinforced concrete columns", J. Struct. Eng., 120(8), 2310-2329. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:8(2310)
  22. Safa, M., Shariati, M., Ibrahim, Z., Toghroli, A., Baharom, S.B., Nor, N.M. and Petkovic, D. (2016), "Potential of adaptive neuro fuzzy inference system for evaluating the factors affecting steelconcrete composite beam's shear strength", Steel Compos. Struct., Int. J., 21(3), 679-688. https://doi.org/10.12989/scs.2016.21.3.679
  23. Tam, V.W.Y., Tam, C.M., Zeng, S.X. and Ng, W.C.Y. (2007), "Towards adoption of prefabrication in construction", Build. Environ., 42(10), 3642-3654. https://doi.org/10.1016/j.buildenv.2006.10.003
  24. Trentadue, F., Quaranta, G., Greco, R. and Marano, G.C. (2015), "New analytical model for the hoop contribution to the shear capacity of circular reinforced concrete columns", Comput. Concrete, 14(1), 59-71. https://doi.org/10.12989/CAC.2014.14.1.059
  25. Uy, B. and Bradford, M.A. (1995), "Ductility of profiled composite beams. part I: experimental study", J. Struct. Eng., 121(5), 876-882. https://doi.org/10.1061/(ASCE)0733-9445(1995)121:5(876)
  26. Vora, T.P. and Shah, B.J. (2016), "Experimental investigation on shear capacity of RC beams with GFRP rebar & stirrups", Steel Compos. Struct., Int. J., 21(6), 1265-1285. https://doi.org/10.12989/scs.2016.21.6.1265
  27. Wang, Q., Shi, Q. and Tian, H. (2016), "Experimental study on shear capacity of src joints with different arrangement and sizes of cross-shaped steel in column", Steel Compos. Struct., Int. J., 21(2), 267-287. https://doi.org/10.12989/scs.2016.21.2.267
  28. Xiao, C., Deng, F., Chen, T. and Zhao, Z. (2017), "Experimental study on concrete-encased composite columns with separate steel sections", Steel Compos. Struct., Int. J., 23(4), 483-491. https://doi.org/10.12989/scs.2017.23.4.483
  29. Xu, C.H., Zeng, L., Zhou, Q., Tu, X. and Wu, Y. (2015), "Cyclic performance of concrete-encased composite columns with tshaped steel sections", Int. J. Civil Eng., 13(4), 456-467.
  30. Xue, J.Y., Gao, L., Liu, Z.Q., Zhao, H.T. and Chen, Z.P. (2014), "Experimental study on mechanical performances of lattice steel reinforced concrete inner frame with irregular section columns", Steel Compos. Struct., Int. J., 16(3), 253-267. https://doi.org/10.12989/scs.2014.16.3.253
  31. Yang, Y., Yu, Y., Guo, Y., Roeder, C.W., Xue, Y. and Shao, Y. (2016), "Experimental study on shear performance of partially precast castellated steel reinforced concrete (CPSRC) beams", Steel Compos. Struct., Int. J., 21(2), 289-302. https://doi.org/10.12989/scs.2016.21.2.289
  32. Yang, Y., Xue, Y., Yu, Y., Ma, N. and Shao, Y. (2017), "Experimental study on flexural performance of partially precast steel reinforced concrete beams", J. Constr. Steel Res., 133, 192-201. https://doi.org/10.1016/j.jcsr.2017.02.019
  33. Zhao, H.T. (2001), Steel-Concrete Composite Structure, Science Press, Beijing, China.
  34. Zhang, S.Q., Chen Z.P., Wang, N. and Chen, Y.L. (2014), "Shear mechanism and shear strength of steel reinforced concrete (SRC) cross-shape 3D column-beam joints", China Civil Eng. J., 9(9), 84-93.