Smart Structures and Systems

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Wheel tread defect detection for high-speed trains using FBG-based online monitoring techniques

  • Liu, Xiao-Zhou (Hong Kong Branch of Chinese National Rail Transit Electrification and Automation Engineering Technology Research Center) ;
  • Ni, Yi-Qing (Hong Kong Branch of Chinese National Rail Transit Electrification and Automation Engineering Technology Research Center)
  • Received : 2017.12.29
  • Accepted : 2018.03.31
  • Published : 2018.05.25
⟨ Previous Next ⟩

Abstract

The problem of wheel tread defects has become a major challenge for the health management of high-speed rail as a wheel defect with small radius deviation may suffice to give rise to severe damage on both the train bogie components and the track structure when a train runs at high speeds. It is thus highly desirable to detect the defects soon after their occurrences and then conduct wheel turning for the defective wheelsets. Online wheel condition monitoring using wheel impact load detector (WILD) can be an effective solution, since it can assess the wheel condition and detect potential defects during train passage. This study aims to develop an FBG-based track-side wheel condition monitoring method for the detection of wheel tread defects. The track-side sensing system uses two FBG strain gauge arrays mounted on the rail foot, measuring the dynamic strains of the paired rails excited by passing wheelsets. Each FBG array has a length of about 3 m, slightly longer than the wheel circumference to ensure a full coverage for the detection of any potential defect on the tread. A defect detection algorithm is developed for using the online-monitored rail responses to identify the potential wheel tread defects. This algorithm consists of three steps: 1) strain data pre-processing by using a data smoothing technique to remove the trends; 2) diagnosis of novel responses by outlier analysis for the normalized data; and 3) local defect identification by a refined analysis on the novel responses extracted in Step 2. To verify the proposed method, a field test was conducted using a test train incorporating defective wheels. The train ran at different speeds on an instrumented track with the purpose of wheel condition monitoring. By using the proposed method to process the monitoring data, all the defects were identified and the results agreed well with those from the static inspection of the wheelsets in the depot. A comparison is also drawn for the detection accuracy under different running speeds of the test train, and the results show that the proposed method can achieve a satisfactory accuracy in wheel defect detection when the train runs at a speed higher than 30 kph. Some minor defects with a depth of 0.05 mm~0.06 mm are also successfully detected.

Keywords

Acknowledgement

Supported by : Research Grants Council of the Hong Kong, Hong Kong Branch of Chinese National Rail Transit Electrification, Automation Engineering Technology Research Center

References

  1. Asplund, M., Famurewa, S. and Rantatalo, M. (2014), "Condition monitoring and e-maintenance solution of railway wheels", J. Qual. Maint. Eng., 20(3), 216-232. https://doi.org/10.1108/JQME-05-2014-0027
  2. Baeza, L., Roda, A., Carballeira, J. and Giner, E. (2006), "Railway train-track dynamics for wheelflats with improved contact models", Nonlinear Dynam., 45(3-4), 385-397. https://doi.org/10.1007/s11071-005-9014-8
  3. Barke, D. and Chiu, W. K. (2005), "Structural health monitoring in the railway industry: a review", Struct. Health Monit., 4(1), 81-93. https://doi.org/10.1177/1475921705049764
  4. Bian, J., Gu, Y. and Murray, M. H. (2013), "A dynamic wheel-rail impact analysis of railway track under wheel flat by finite element analysis", Vehicle. Syst. Dyn., 51(6), 784-797. https://doi.org/10.1080/00423114.2013.774031
  5. Ding, J., Lin, J., Wang, G. and Zhao, J. (2014), "Time-frequency analysis of wheel-rail shock in the presence of wheel flat", J. Traffic Transp. Eng. (English Edition), 1(6), 457-466. https://doi.org/10.1016/S2095-7564(15)30296-8
  6. Ding, Y., An, Y. and Wang, C. (2016), "Field monitoring of the train-induced hanger vibration in a high-speed railway steel arch bridge", Smart Struct. Syst., 17(6), 1107-1127. https://doi.org/10.12989/sss.2016.17.6.1107
  7. Filograno, M. L., Corredera, P., Rodriguez-Plaza, M., Andres-Alguacil, A. and Gonzalez-Herraez, M. (2013), "Wheel flat detection in high-speed railway systems using fiber Bragg gratings", IEEE Sens. J., 13(12), 4808-4816. https://doi.org/10.1109/JSEN.2013.2274008
  8. Johansson, A. and Nielsen, J. C. (2003), "Out-of-round railway wheels-wheel-rail contact forces and track response derived from field tests and numerical simulations", Proc. Instn. Mech. Engrs., Part F: Journal of Rail and Rapid Transit, 217(2), 135-146. https://doi.org/10.1243/095440903765762878
  9. Lagneback, R. (2007), "Evaluation of wayside condition monitoring technologies for condition-based maintenance of railway vehicles", Ph.D. Dissertation, Lulea Tekniska Universitet, Lulea.
  10. Milkovic, D., Simic, G., Jakovljevic, Z., Tanaskovic, J. and Lucanin, V. (2013), "Wayside system for wheel-rail contact forces measurements", Measurement, 46(9), 3308-3318. https://doi.org/10.1016/j.measurement.2013.06.017
  11. Morys, B. (1999), "Enlargement of out-of-round wheel profiles on high speed trains", J. Sound Vib., 227(5), 965-978. https://doi.org/10.1006/jsvi.1999.2055
  12. Muller-BBM (2015), "Wheel roughness measuring device mwheel", Muller-BBM Rail Technologies GmbH, Munchen, Germany. Available at: http://www.muellerbbmrail.com/products/wheel-roughness-measuring-device/
  13. Ni, Y.Q. (2015), "SHM-enriched high speed rail systems", Proceedings of the 10th International Workshop on Structural Health Monitoring, Stanford, California, USA.
  14. Ni, Y.Q., Ying, Z.G. and Liu, X.Z. (2017), "Online detection of wheel defect by extracting anomaly response features on rail: analytical modelling, monitoring system design, and in-situ verification", Proceedings of the 14th International Conference on Railway Engineering, Edinburgh, UK.
  15. Nielsen, J.C. and Oscarsson, J. (2004), "Simulation of dynamic train-track interaction with state-dependent track properties", J. Sound Vib., 275(3), 515-532. https://doi.org/10.1016/j.jsv.2003.06.033
  16. Petersson, M. (2000), "Noise-related roughness of railway wheel treads-full-scale testing of brake blocks", Proc. Instn. Mech. Engrs., Part F: Journal of Rail and Rapid Transit, 214(2), 63-77. https://doi.org/10.1243/0954409001531342
  17. Pieringer, A., Kropp, W. and Nielsen, J. C. (2014), "The influence of contact modelling on simulated wheel/rail interaction due to wheel flats", Wear, 314(1), 273-281. https://doi.org/10.1016/j.wear.2013.12.005
  18. Savitzky, A. and Golay, M.J. (1964), "Smoothing and differentiation of data by simplified least squares procedures", Anal. Chem., 36(8), 1627-1639. https://doi.org/10.1021/ac60214a047
  19. Wei, C., Xin, Q., Chung, W.H., Liu, S.Y., Tam, H.Y. and Ho, S.L. (2012), "Real-time train wheel condition monitoring by fiber Bragg grating sensors", Int. J. Distrib. Sens. N., 8(1), 409048. https://doi.org/10.1155/2012/409048
  20. Wei, X. and Chen, J. (2013), "Study on wheel-flat detection method based on vehicle system acceleration measurement", Proceedings of the International Conference on Measurement, Information and Control (ICMIC), IEEE, Harbin, China.
  21. Wu, T.X. and Thompson, D.J. (2002), "A hybrid model for the noise generation due to railway wheel flats", J. Sound Vib., 251(1), 115-139. https://doi.org/10.1006/jsvi.2001.3980
  22. Yang, J. and Thompson, D. J. (2014), "Time-domain prediction of impact noise from wheel flats based on measured profiles", J. Sound Vib., 333(17), 3981-3995. https://doi.org/10.1016/j.jsv.2014.04.026
  23. Ye, X. W., Yi, T.H., Su, Y.H., Liu, T. and Chen, B. (2017), "Strain-based structural condition assessment of an instrumented arch bridge using FBG monitoring data", Smart Struct. Syst., 20(2), 139-150. https://doi.org/10.12989/SSS.2017.20.2.139
  24. Zhang, X., Liang, D., Zeng, J. and Lu, J. (2014), "SVR model reconstruction for the reliability of FBG sensor network based on the CFRP impact monitoring", Smart Struct. Syst., 14(2), 145-158. https://doi.org/10.12989/sss.2014.14.2.145
  25. Zhao, X., Li, Z. and Liu, J. (2012), "Wheel-rail impact and the dynamic forces at discrete supports of rails in the presence of singular rail surface defects", Proc. Instn. Mech. Engrs., Part F: Journal of Rail and Rapid Transit, 226(2), 124-139. https://doi.org/10.1177/0954409711413975

Cited by

  1. Critical coupling span number in high-speed railway simply supported beam bridge vol.28, pp.1, 2018, https://doi.org/10.12989/sss.2021.28.1.013