Journal of the Korean Society of Manufacturing Process Engineers (한국기계가공학회지)

The Korean Society of Manufacturing Process Engineers (한국기계가공학회)
권호 표지
DOI QR코드

DOI QR Code

A Study on the Durability due to Fork Shape of Excavator Bucket

굴삭기 버켓의 포크 형상에 따른 내구성 연구

  • Han, Moonsik (Department of Mechanical and Automotive Engineering, Keimyung UNIV.) ;
  • Cho, Jaeung (Division of Mechanical and Automotive Engineering, Kongju National UNIV.)
  • 한문식 (계명대학교 기계자동차공학과) ;
  • 조재웅 (공주대학교 기계자동차공학부)
  • Received : 2018.02.10
  • Accepted : 2018.03.04
  • Published : 2018.04.30
Download PDF
⟨ Previous Next ⟩

Abstract

In this study, the durability due to the fork shape of excavator bucket is investigated. The analysis is carried out by modelling the fork shape used in general. As the analysis condition, the pin is constrained as fixed support at the bucket and the load of 12000N is applied at the fork. As the study result, the maximum equivalent stresses at models 1 and 2 are shown as 56.895MPa and 54.722MPa respectively. Model 1 is shown to have the most deformation of 5.6686 mm among four models. Model 3 has the least deformation among four models and the maximum deformation of model 3 is shown as 4.948mm. The fatigue analyses are also carried out with three models. Each model shows the same fatigue lives under the identical fatigue loads. The damage part at each model is shown at the bucket pork or the pin connected with bucket. As this study result, the data is thought to contribute to the safety design at excavator bucket.

Keywords

References

  1. Cho, J. U., Han, M. S., "Structural Safety Analysis of Car Body," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 7, No. 3, pp. 12-16, 2008.
  2. Cho, J. U., Min, B. S., Han, M. S., "Basic Study on Impact Analysis of Automobile," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 8, No. 1, pp. 64-70, 2009.
  3. Kang, H. J., Kim, B. H., Kim, H. J., Seo, J. H., "Structural Weld Strength Analysis on Door Hinge of Field Artillery Ammunition Support Vehicle," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 15, No. 3, pp. 58-65, 2016. https://doi.org/10.14775/ksmpe.2016.15.3.058
  4. Ryu, J. M., Park, K. C., Kang, T. W., "A Study on the Structural Design for Safety Improvement of the Winch Mount of an Armored Recovery Vehicle," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 1, pp. 58-62, 2017. https://doi.org/10.14775/ksmpe.2016.16.1.058
  5. Cho, J. U., Han, M. S., "A Study on Durability of Under Bar at Car through Structural and Fatigue Analysis," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 2, pp. 44-50, 2015. https://doi.org/10.14775/ksmpe.2015.14.2.044
  6. Lee, J. I., "The Convergence Design for Stiffness and Structure Advancement of Automotive Body," Journal of the Korea Convergence Society, Vol. 8, No. 4, pp. 189-197, 2017. https://doi.org/10.15207/JKCS.2017.8.4.189
  7. Cho, J. U., Han, M. S., "Durability Study on Structural Strength due to the Shape of Excavator Wheel," Transaction of the Korean Society of Automotive Engineers, Vol. 21, No. 6, pp. 166-174, 2013. https://doi.org/10.7467/KSAE.2013.21.6.166
  8. Yoo, B. S., Koo, S. W., Joh, J. S., "A Study on Suppression of Vibration Caused by Quick-stop Operation of Hydraulic Excavator Boom," Journal of the Korean Society for Precision Engineering, Vol. 27, No. 12, pp. 33-40, 2010
  9. Moon, S. G., Park, Y. J., Lee, G. H., "Determination of Equivalent Moment of Inertia of Flywheel for Inertial Endurance Test of Excavator Slewing System," Journal of the Korean Society for Precision Engineering, Vol. 34, No. 6, pp. 383-390, 2017. https://doi.org/10.7736/KSPE.2017.34.6.383
  10. Lee, Y. S., Ok, J. K., Kim, H. J., Yoo, W. S., "Analytical Investigation on the Track Separation Mechanism for Tracked Excavator," Transaction of the Korean Society of Automotive Engineers, Vol. 14, No. 6, pp. 66-72, 2006.

Cited by

  1. Damping Device for Hydraulic Breaker: Impact and Noise Reduction vol.17, pp.4, 2018, https://doi.org/10.14775/ksmpe.2018.17.4.113
  2. A Safety Study Using Impact and Fatigue Analyses According to Headrest Shape vol.17, pp.3, 2018, https://doi.org/10.14775/ksmpe.2018.17.3.039