DOI QR코드

DOI QR Code

Use of e-plastic waste in concrete as a partial replacement of coarse mineral aggregate

  • Sabau, Marian (Department of Civil and Environmental Engineering, Universidad de la Costa) ;
  • Vargas, Johnny R. (Department of Civil and Environmental Engineering, Universidad de la Costa)
  • 투고 : 2017.03.28
  • 심사 : 2017.11.28
  • 발행 : 2018.04.25

초록

The accelerated increase of the population growth rate in the world and the current lifestyle based on consumerism considerably increased the amount of waste generated by the human activity. Specifically, e-plastic waste causes significant damage to the environment because of its difficult degradation process. This paper aims to establish the feasibility of using e-plastic waste in concrete as a partial replacement of coarse mineral aggregate. Considering a control mix without e-plastic waste designed for a compressive strength of 21 MPa, tests on concrete mixes with 40, 50 and 60% of e-plastic waste aggregate to determine the fresh and hardened properties were carried out. A reduction in the compressive strength as the percentage of e-plastic waste increases was observed, the maximum reduction being 44% with respect to the control mix. In addition, a significant reduction as much as 22% in the density of the concrete mixes with e-plastic waste was recorded, which means that lighter elements can be produced with this type of concrete. Two new equations based on regression analysis of the experimental data from this study were proposed. These equations estimate the reduction in the compressive strength of concrete mixes with e-plastic waste aggregate at 14 and 28 days. A cost analysis and a practical alternative to introduce this waste material into the market are also presented.

키워드

과제정보

연구 과제 주관 기관 : Universidad de la Costa

참고문헌

  1. ACI 211.1-91 (1991), Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, American Concrete Institute, Farmington Hills, MI, USA.
  2. Ahmadi, B. and Al-Khaja, W. (2001), "Utilization of paper waste sludge in the building construction industry", Resour. Conserv. Recycl., 32(2), 105-113. https://doi.org/10.1016/S0921-3449(01)00051-9
  3. Akcaozoglu, S., Atis, C.D. and Akcaozoglu, K. (2010), "An investigation on the use of shredded waste PET bottles as aggregate in lightweight concrete", Waste Manag., 30(2), 285-290. https://doi.org/10.1016/j.wasman.2009.09.033
  4. Akram, A., Sasidhar, C. and Pasha, K. (2015), "E-Waste Management by Utilization of E-Plastics in Concrete Mixtures as Coarse Aggregate Replacement", Int. J. Innov. Res. Sci. Eng. Technol., 4(7), 5087-5095. https://doi.org/10.15680/IJIRSET.2015.0407008
  5. Andrade, L.B., Rocha, J.C. and Cheriaf, M. (2009), "Influence of coal bottom ash as fine aggregate on fresh properties of concrete", Constr. Build. Mater., 23(2), 609-614. https://doi.org/10.1016/j.conbuildmat.2008.05.003
  6. Argos-Productos (2017), Cemento Gris Uso General, Argos, Medellin, Colombia.
  7. Arora, A. and Dave, U. (2013), "Utilization of E-waste and plastic bottle waste", Int. J. Stud. Res. Technol. Manage., 1(4), 398-406.
  8. Asociacion Colombiana de Ingenieria Sismica (2010), Reglamento Colombiano de Construccion Sismo Resistente (NSR-10), Bogota D.C., Colombia.
  9. Asokan, P., Osmani, M. and Price, A. (2010), "Improvement of the mechanical properties of glass fibre reinforced plastic waste powder filled concrete", Constr. Build. Mater., 24(4), 448-460. https://doi.org/10.1016/j.conbuildmat.2009.10.017
  10. ASTM C1157/C1157M-11 (2011), Standard Performance Specification for Hydraulic Cement, ASTM International, West Conshohocken, PA, USA.
  11. ASTM C136/C136M-14 (2014), Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates, ASTM International, West Conshohocken, PA, USA.
  12. ASTM C143/C143M-15a (2015), Standard Test Method for Slump of Hydraulic-Cement Concrete, ASTM International, West Conshohocken, PA, USA.
  13. ASTM C192/C192M-16a (2016), Standard Practice for Making and Curing Concrete Test Specimens in the Laboratory, ASTM International,West Conshohocken, PA, USA.
  14. ASTM C39/C39M-16b (2016), Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens, ASTM International,West Conshohocken, PA, USA.
  15. ASTM D256-10e1 (2010), Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics, ASTM International,West Conshohocken, PA, USA.
  16. ASTM D638-14 (2014), Standard Test Method for Tensile Properties of Plastics, ASTM International, West Conshohocken, PA, USA.
  17. ASTM D785-08 (2015), Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials, ASTM International,West Conshohocken, PA, USA.
  18. ASTM D790-15e2 (2015), Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials, ASTM International, West Conshohocken, PA.
  19. Baffa, I. and Akasaki, J. (2005), "Light-concrete with leather: durability aspects", International Conference for Structures, Coimbra, Portugal.
  20. Batayneh, M., Marie, I. and Asi, I. (2007), "Use of selected waste materials in concrete mixes", Waste Manage., 27(12), 1870-1876. https://doi.org/10.1016/j.wasman.2006.07.026
  21. Bompa, D.V. and Elghazouli, A.Y. (2017), "Bond-slip response of deformed bars in rubberised concrete", Constr. Build. Mater., 154, 884-898. https://doi.org/10.1016/j.conbuildmat.2017.08.016
  22. Bompa, D.V., Elghazouli, A.Y., Xu, B., Stafford, P.J. and Ruiz-Teran, A.M. (2017), "Experimental assessment and constitutive modelling of rubberised concrete materials", Constr. Build. Mater., 137, 246-260. https://doi.org/10.1016/j.conbuildmat.2017.01.086
  23. Cyr, M. and Ludmann, C. (2006), "Low risk meat and bone meal (MBM) bottom ash in mortars as sand replacement", Cement Concrete Res., 36(3), 469-480. https://doi.org/10.1016/j.cemconres.2005.09.009
  24. DANE (2016), Indicadores Basicos de Tenencia y Uso de Tecnologias de la Informacion y Comunicacion-TIC en Hogares y Personas de 5 y mas anos de edad 2015, DANE, Bogota D.C., Colombia.
  25. Elghazouli, A.Y., Bompa, D.V., Xu, B., Stafford, P.J. and Ruiz-Teran, A.M. (2018), "Inelastic behaviour of RC members incorporating high deformability concrete", High Tech Concrete: Where Technology and Engineering Meet, Springer International Publishing, Cham.
  26. Gawatre, D., Damal, V., Londhe, S., Mane, A. and Ghawate, H. (2015), "Environmental issues of plastic waste use in concrete", Int. J. Innov. Res. Adv. Eng., 2(5), 114-117.
  27. Guney, Y., Sari, Y.D., Yalcin, M., Tuncan, A. and Donmez, S. (2010), "Re-usage of waste foundry sand in high-strength concrete", Waste Manage., 30(8-9), 1705-1713. https://doi.org/10.1016/j.wasman.2010.02.018
  28. Jo, B.W., Park, S.K. and Park, J.C. (2008), "Mechanical properties of polymer concrete made with recycled PET and recycled concrete aggregates", Constr. Build. Mater., 22(12), 2281-2291. https://doi.org/10.1016/j.conbuildmat.2007.10.009
  29. Kim, H.K. and Lee, H.K. (2011), "Use of power plant bottom ash as fine and coarse aggregates in high-strength concrete", Constr. Build. Mater., 25(2), 1115-1122. https://doi.org/10.1016/j.conbuildmat.2010.06.065
  30. Kinuthia, J., Snelson, D. and Gailius, A. (2009), "Sustainable medium-strength concrete (CS-concrete) from colliery spoil in South Wales UK", J. Civ. Eng. Manage., 15(2), 149-157. https://doi.org/10.3846/1392-3730.2009.15.149-157
  31. Kurup, A.R. and Senthil Kumar, K. (2017), "Novel fibrous concrete mixture made from recycled PVC fibers from electronic waste", J. Hazard. Toxic Radioact. Waste, 21(2), 4016020. https://doi.org/10.1061/(ASCE)HZ.2153-5515.0000338
  32. Lakshmi, R. and Nagan, S. (2010), "Studies on concrete containing E plastic waste", Int. J. Environ. Sci., 1(3), 270-281.
  33. Lakshmi, R. and Nagan, S. (2011), "Investigations on durability characteristics of E-plastic waste incorporated concrete", Asian J. Civil Eng. (Build. Hous.), 12(6), 773-787.
  34. Manatkar, P. and Deshmukh, G. (2015), "Use of non-metallic ewaste as a coarse aggregate in a concrete", Int. J. Res. Eng. Technol., 4(3), 242-246.
  35. Manjunath, A. (2016), "Partial replacement of E-plastic Waste as Coarse-aggregate in Concrete", Procedia Environ. Sci., 35, 731-739. https://doi.org/10.1016/j.proenv.2016.07.079
  36. Ministerio de Ambiente (2014), Reciclar, Una Nueva Costumbre, El Espectador, 129-136.
  37. Naik, T.R., Friberg, T.S. and Chun, Y. (2004), "Use of pulp and paper mill residual solids in production of cellucrete", Cement Concrete Res., 34(7), 1229-1234. https://doi.org/10.1016/j.cemconres.2003.12.013
  38. Pacheco-Torgal, F. and Jalali, S. (2010), "Reusing ceramic wastes in concrete", Constr. Build. Mater., 24(5), 832-838. https://doi.org/10.1016/j.conbuildmat.2009.10.023
  39. Papayianni, I. and Anastasiou, E. (2010), "Production of highstrength concrete using high volume of industrial by-products", Constr. Build. Mater., 24(8), 1412-1417. https://doi.org/10.1016/j.conbuildmat.2010.01.016
  40. Plastics International (2017), ABS, Plastics International, Eden Prairie, MN, USA.
  41. Rao, S.M., Reddy, B.V.V., Lakshmikanth, S. and Ambika, N.S. (2009), "Re-use of fluoride contaminated bone char sludge in concrete", J. Hazard. Mater., 166(2-3), 751-756. https://doi.org/10.1016/j.jhazmat.2008.11.115
  42. Sadrmomtazi, A., Dolati-Milehsara, S., Lotfi-Omran, O. and Sadeghi-Nik, A. (2016), "The combined effects of waste Polyethylene Terephthalate (PET) particles and pozzolanic materials on the properties of self-compacting concrete", J. Clean. Prod., 112, 2363-2373. https://doi.org/10.1016/j.jclepro.2015.09.107
  43. Sales, A. and de Souza, F.R. (2009), "Concretes and mortars recycled with water treatment sludge and construction and demolition rubble", Constr. Build. Mater., 23(6), 2362-2370. https://doi.org/10.1016/j.conbuildmat.2008.11.001
  44. Santiago, E.Q.R., Lima, P.R.L., Leite, M.B. and Toledo Filho, R.D. (2009), "Mechanical behavior of recycled lightweight concrete using EVA waste and CDW under moderate temperature", Rev. IBRACON Estruturas E Mater., 2(3), 211-221. https://doi.org/10.1590/S1983-41952009000300001
  45. Senthil Kumar, K. and Baskar, K. (2014), "Response surfaces for fresh and hardened properties of concrete with E-waste (HIPS)", J. Waste Manag., 2014, Article ID 517219.
  46. Senthil Kumar, K. and Baskar, K. (2015a), "Development of ecofriendly concrete incorporating recycled high-impact polystyrene from hazardous electronic waste", J. Hazard. Toxic Radioact. Waste, 19(3), 4014042. https://doi.org/10.1061/(ASCE)HZ.2153-5515.0000265
  47. Senthil Kumar, K. and Baskar, K. (2015b), "Recycling of E-plastic waste as a construction material in developing countries", J. Mater. Cycles Waste Manage., 17(4), 718-724. https://doi.org/10.1007/s10163-014-0303-5
  48. Senthil Kumar, K., Premalatha, P.V. and Baskar, K. (2017), "Evaluation of transport properties of concrete made with Ewaste plastic", J. Test. Eval., 45(5), 20160008. https://doi.org/10.1520/JTE20160008
  49. Senthil Kumar, K., Premalatha, P.V., Baskar, K., Sankaran Pillai, G. and Shahul Hameed, P. (2018), "Assessment of radioactivity in concrete made with e-waste plastic", J. Test. Eval., 46(2), 20160006. https://doi.org/10.1520/JTE20160006
  50. Siddique, R., Khatib, J. and Kaur, I. (2008), "Use of recycled plastic in concrete: A review", Waste Manage., 28(10), 1835-1852. https://doi.org/10.1016/j.wasman.2007.09.011
  51. Silva, R.V., de Brito, J. and Saikia, N. (2013), "Influence of curing conditions on the durability-related performance of concrete made with selected plastic waste aggregates", Cememt Concrete Compos., 35(1), 23-31. https://doi.org/10.1016/j.cemconcomp.2012.08.017
  52. Teo, D.C.L., Mannan, M.A. and Kurian, V.J. (2010), "Durability of lightweight OPS concrete under different curing conditions", Mater. Struct., 43(1-2), 1-13.
  53. Vargas, J. and Polo, E. (2017), "Obtencion de una mezcla de concreto con residuos plasticos de equipos electronicos para la fabricacion de elementos no estructurales", Universidad de la Costa, Barranquilla, Colombia.
  54. Wang, C.C., Chen, T.T., Wang, H.Y. and Huang, C. (2014), "A predictive model for compressive strength of waste LCD glass concrete by nonlinear-multivariate regression", Comput. Concrete, 13(4), 531-545. https://doi.org/10.12989/cac.2014.13.4.531
  55. Wang, H.Y. and Chen, J.S. (2008), "Study of thin film transition liquid crystal display (TFT-LCD) optical waste glass applied in early-high-strength controlled low strength materials", Comput. Concrete, 5(5), 491-501. https://doi.org/10.12989/cac.2008.5.5.491
  56. Wang, H.Y., Hsiao, D.H. and Wang, S.Y. (2012), "Properties of recycled green building materials applied in lightweight aggregate concrete", Comput. Concrete, 10(2), 95-104. https://doi.org/10.12989/cac.2012.10.2.095
  57. Xu, B., Bompa, D.V., Elghazouli, A.Y., Ruiz-Teran, A.M. and Stafford, P.J. (2018), "Behaviour of rubberised concrete members in asymmetric shear tests", Constr. Build. Mater., 159, 361-375. https://doi.org/10.1016/j.conbuildmat.2017.10.091
  58. Yellishetty, M., Karpe, V., Reddy, E.H., Subhash, K.N. and Ranjith, P.G. (2008), "Reuse of iron ore mineral wastes in civil engineering constructions: A case study", Resour. Conserv. Recycl., 52(11), 1283-1289. https://doi.org/10.1016/j.resconrec.2008.07.007
  59. Yuksel, I., Siddique, R. and Ozkan, O. (2011), "Influence of high temperature on the properties of concretes made with industrial by-products as fine aggregate replacement", Constr. Build. Mater., 25(2), 967-972. https://doi.org/10.1016/j.conbuildmat.2010.06.085