Steel and Composite Structures

  • 제26권4호
  • /
  • Pages.485-499
  • /
  • 2018
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Direct shear behavior of concrete filled hollow steel tube shear connector for slim-floor steel beams

  • Hosseinpour, Emad (Department of Civil and Structural Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia) ;
  • Baharom, Shahrizan (Department of Civil and Structural Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia) ;
  • Badaruzzaman, Wan Hamidon W. (Department of Civil and Structural Engineering, Faculty of Engineering and Built Environment, Universiti Kebangsaan Malaysia) ;
  • Shariati, Mahdi (Faculty of Civil Engineering, University of Tabriz) ;
  • Jalali, Abdolrahim (Faculty of Civil Engineering, University of Tabriz)
  • 투고 : 2017.04.14
  • 심사 : 2017.12.14
  • 발행 : 2018.02.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, a hollow steel tube (HST) shear connector is proposed for use in a slim-floor system. The HST welded to a perforated steel beam web and embedded in concrete slab. A total of 10 push-out tests were conducted under static loading to investigate the mechanical behavior of the proposed HST connector. The variables were the shapes (circular, square and rectangular) and sizes of hollow steel tubes, and the compressive strength of the concrete. The failure mode was recorded as: concrete slab compressive failure under the steel tube and concrete tensile splitting failure, where no failure occurred in the HST. Test results show that the square shape HST in filled via concrete strength 40 MPa carried the highest shear load value, showing three times more than the reference specimens. It also recorded less slip behavior, and less compressive failure mode in concrete underneath the square hollow connector in comparison with the circular and rectangular HST connectors in both concrete strengths. The rectangular HST shows a 20% higher shear resistance with a longer width in the load direction in comparison with that in the smaller dimension. The energy absorption capacity values showed 23% and 18% improvements with the square HST rather than a headed shear stud when embedded in concrete strengths of 25 MPa and 40 MPa, respectively. Moreover, an analytical method was proposed and predicts the shear resistance of the HST shear connectors with a standard deviation of 0.14 considering the shape and size of the connectors.

키워드

과제정보

연구 과제 주관 기관 : Ministry of Higher Education of Malaysia (MOHE), Universiti Kebangsaan Malaysia (UKM)

참고문헌

  1. Al Zand, A.W., Badaruzzaman, W.H.W., Mutalib, A.A. and Hilo, S.J. (2016), "The enhanced performance of CFST beams using different strengthening schemes involving unidirectional CFRP sheets: An experimental study", Eng. Struct., 12(8), 184-198.
  2. An, L. and Cederwall, K. (1996), "Push-out tests on studs in high strength and normal strength concrete", J. Constr. Steel Res., 36(1), 15-29. https://doi.org/10.1016/0143-974X(94)00036-H
  3. Anagnostopoulos, C.A. (2014), "Effect of different superplasticizers on the physical and mechanical properties of cement grouts", Constr. Build. Mater., 50(1), 162-168. https://doi.org/10.1016/j.conbuildmat.2013.09.050
  4. Arivalagan, K. (2009), "Energy absorption capacity of composite beams", J. Eng. Sci. Technol. Rev., 2(1), 145-150.
  5. Baharom, S. and Hosseinpour, E. (2015), "Shear behavior of innovative connectors in partially encased column", Proceedings of World Congress on Advances in Structural Engineering and Mechanics (ASEM15), Incheon, Korea, August.
  6. Candido-Martins, J.P.S., Costa-Neves, L.F. and Vellasco, P.C.G.d.S. (2010), "Experimental evaluation of the structural response of perfobond shear connectors", Eng Struct., 32(8), 1976-1985. https://doi.org/10.1016/j.engstruct.2010.02.031
  7. Chen, S., Limazie, T. and Tan, J. (2015), "Flexural behavior of shallow cellular composite floor beams with innovative shear connections", J. Constr. Steel Res., 10(6), 329-346.
  8. Chung, K.F. (2002), "Composite beams and floor systems fully integrated with building services", Progress in Structural Engineering and Materials, 4(2), 169-178. https://doi.org/10.1002/pse.116
  9. Chung, K.F., Ko, C.H. and Wang, A.J. (2005), "Design of steel and composite beams with web openings - verification using finite element method", Steel Compos. Struct., Int. J., 5(2-3), 203-233. https://doi.org/10.12989/scs.2005.5.2_3.203
  10. Classen, M. (2015), "Shear behavior of composite dowels in transversely cracked concrete", Struct. Concrete, 6(2), 195-206.
  11. Classen, M., Herbrand, M., Kueres, D. and Hegger, J, (2016), "Derivation of design rules for innovative shear connectors in steel concrete composites by systematic use of nonlinear finite element analysis (FEA)", Struct. Concrete, 4(17), 646-655.
  12. Costa-Neves, L.F., Figueiredo, J.P., Vellasco, P.C.G.d.S. and Vianna, J.d.C. (2013), "Perforated shear connectors on composite girders under monotonic loading: An experimental approach", Eng. Struct., 5(6), 721-737.
  13. De Nardin, S. and El Debs, A.L.H.C. (2012), Composite connections in slim-floor system: An experimental study. J. Constr. Steel Res., 68(1), 78-88. https://doi.org/10.1016/j.jcsr.2011.07.006
  14. Euro Code of practice 4 (2004), "Design of Composite Steel and Concrete Structures, part 1-1, General Rules and Rules for Buildings", European Committee for Standardization.
  15. Euro Code of practice 4 (2005), "Design of Composite Steel and Concrete Structures, part 2, General Rules and Rules for Bridges", European Committee for Standardization.
  16. Fontana, M. and Beck, H. (2002), "Experimental Studies on Novel Shear Rib Connectors with Powder-Actuated Fasteners", Proceedings of Composite Construction in Steel and Concrete IV, Alberta, Canada, April.
  17. Gallwoszus, J. (2016), "Concrete fatigue in composite dowels", Struct. Concrete, 17(1), 63-73. https://doi.org/10.1002/suco.201400120
  18. Gattesco, N. and Giuriani, E. (1996), "Experimental Study on Stud Shear connectors subjected to cyclic loading", J. Constr. Steel Res., 38(1), 1-12. https://doi.org/10.1016/0143-974X(96)00007-7
  19. Han, Q., Wang, Y., Xu, J. and Xing, Y. (2015), "Static behavior of stud shear connectors in elastic concrete-steel composite beams", J. Constr. Steel Res., 11(3), 115-126.
  20. Hegger, J. and Goralski, C. (2004), "Structural behavior of partially concrete encased composite sections with high strength cocrete", Proceedings of Composite Construction in Steel and Concrete V, Mpumalanga, South Africa, July.
  21. Huo, B.Y. (2012), "Experimental and analytical study of the shear transfer in composite shallow cellular floor beams", Ph.D. Dissertation; City University London, London, UK.
  22. Huo, B.Y. and D'Mello, C.A. (2013), "Push-out tests and analytical study of shear transfer mechanisms in composite challow cellular floor Beams", J. Constr. Steel Res., 8(8), 191-205.
  23. Kazunori, F., Tomonori, O. and Takashi, N. (1988), "Experimental study on energy absorption capacity of reinforced concrete frames", Doboku Gakkai Ronbunshu, 390, pp. 113-121.
  24. Kuhlmann, U. and Kurschner, K. (2006), "Structural behavior of horizontally lying shear studs", Proceedings of 5th International Conference on Composite Construction in Steel and Concrete, Mpumalanga, South Africa, July, pp. 543.
  25. Kwon, G., Engelhardt, M. and Klingner, R. (2011), "Parametric studies and preliminary design recommendations on the use of post installed shear connectors for strengthening non-composite steel bridges", J. Bridge Eng., 17(2), 310-317. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000261
  26. Limazie, T. and Chen, S. (2016), "FE modeling and numerical investigation of shallow cellular composite floor beams", J. Constr. Steel Res., 11(9), 190-201.
  27. Limazie, T. and Chen, S. (2017), "Effective shear connection for shallow cellular composite floor beams", Constr. Steel Res., 12(8), 772-788.
  28. Lowe, D., Das, R. and Clifton, C. (2014), "Characterization of the splitting behavior of steel-concrete composite beams with shear stud connection", Procedia Mater. Sci., 3(1), 2174-2179. https://doi.org/10.1016/j.mspro.2014.06.352
  29. Mangerig, I. and Capfe, Z. (2003), "Concrete dowels in composite construction", Proceedings of Japanese-German Bridge Symposium, Osaka, Japan, September.
  30. Morkhade, S.G. and Gupta, L.M. (2015), "Analysis of steel I-beams with rectangular web openings: Experimental and finite element investigation", Eng. Struct. Technol., 7(1), 13-23. https://doi.org/10.3846/2029882X.2015.1085332
  31. Nguyen, H.T. and Kim, S.E. (2009), "Finite element modeling of push-out tests for large stud shear connectors", J. Constr. Steel Res., 65(10-11), 1909-1920. https://doi.org/10.1016/j.jcsr.2009.06.010
  32. Pavlovic, M., Markovic, Z., Veljkovic, M. and Budevac, D. (2013), "Bolted shear connectors vs. headed studs behaviour in push-out tests", J. Constr. Steel Res., 8(8), 134-149.
  33. Rodrigues, F., Vellasco, P.C.G.d.S., Lima, L.R.O.d. and Andrade, S.A.L.d. (2014), "Finite element modelling of steel beams with web openings", Engineering, 6(13), 886-913. https://doi.org/10.4236/eng.2014.613082
  34. Shariati, M., Ramli Sulong, N.H., Suhatril, M., Shariati, A., Arabnejad Khanouki, M.M. and Sinaei, H. (2013), "Comparison of behavior between channel and angle shear connectors under monotonic and fully reversed cyclic loading", Constr. Build. Mater., 3(8), 582-593.
  35. Slim-Floor, A., Commercial Section (2007), http://www.arcelormittal.com/sections/
  36. Su, Q., Yang, G. and Bradford, M. (2016), "Bearing capacity of stud-bolt hybrid shear connection in segmental composite bridge girders", J. Bridge Eng., 21(4), 06015008-1-06015008-8. https://doi.org/10.1061/(ASCE)BE.1943-5592.0000873
  37. Tsavdaridis, K.D., D'Mello, C. and Huo, B.Y. (2013), "Experimental and computational study of the vertical shear behaviour of partially encased perforated steel beams", Eng. Struct., 5(6), 805-822.
  38. Uenaka, K. and Higashiyama, H. (2013), "Experimental Study on Half-Pipe Shear Connectors Under Direct Shear", Proceedings of Advances in Structural Engineering and Mechanics (ASEM), Jeju, Korea, September.
  39. Uenaka, K. and Higashiyama, H. (2015), "Mechanical characteristics of hollow shear connectors under direct shear force", Steel Compos. Struct., Int. J., 18(2), 467-480. https://doi.org/10.12989/scs.2015.18.2.467
  40. Vianna, J.D.C., Costa-Neves, L.F., Vellasco, P.C.G.d.S. and Andrade, S.A.L.d. (2008), "Structural behavior of T-Perfobond shear connectors in composite girders: An experimental approach", Eng. Struct., 30(9), 2381-2391. https://doi.org/10.1016/j.engstruct.2008.01.015
  41. ViscoCrete-2055, S. (2011), https://usa.sika.com/en/solutions_products.html
  42. Wang, J., Afshan, S., Gkantou, M., Theofanous, M., Baniotopoulos, C. and Gardner, L. (2016), "Flexural behavior of hot-finished high strength steel square and rectangular hollow sections", J. Const. Steel Res., 1(21), 97-109.
  43. Xu, C. and Sugiura, K. (2013), "FEM analysis on failure development of group studs shear connector under effects of concrete strength and stud dimension", Eng. Failure Anal., 3(5), 343-354.
  44. Xue, D., Liu, Y., Yu, Z. and He, J. (2012), "Static behavior of multi-stud shear connectors for steel-concrete composite bridge", J. Constr. Steel Res., 7(4), 1-7.
  45. Yousuf, M., Brian, U., Tao, Z., Remmenikov, A. and Richard L.J.Y. (2013), "Transverse impact resistance of hollow and concrete filled stainless steel columns", J. Constr. Steel Res., 8(2), 177-189.

피인용 문헌

  1. Flexural performance of cold-formed square CFST beams strengthened with internal stiffeners vol.34, pp.1, 2018, https://doi.org/10.12989/scs.2020.34.1.123
  2. Identification of the most influencing parameters on the properties of corroded concrete beams using an Adaptive Neuro-Fuzzy Inference System (ANFIS) vol.34, pp.1, 2018, https://doi.org/10.12989/scs.2020.34.1.155
  3. Experimental study on axial compressive behavior of welded built-up CFT stub columns made by cold-formed sections with different welding lines vol.34, pp.3, 2018, https://doi.org/10.12989/scs.2020.34.3.347
  4. Numerical study on the axial compressive behavior of built-up CFT columns considering different welding lines vol.34, pp.3, 2018, https://doi.org/10.12989/scs.2020.34.3.377
  5. The effect of RBS connection on energy absorption in tall buildings with braced tube frame system vol.34, pp.3, 2018, https://doi.org/10.12989/scs.2020.34.3.393
  6. Computational estimation of the earthquake response for fibre reinforced concrete rectangular columns vol.34, pp.5, 2018, https://doi.org/10.12989/scs.2020.34.5.743
  7. Elevated temperature resistance of concrete columns with axial loading vol.9, pp.4, 2018, https://doi.org/10.12989/acc.2020.9.4.355
  8. Computational analysis of three dimensional steel frame structures through different stiffening members vol.35, pp.2, 2018, https://doi.org/10.12989/scs.2020.35.2.187
  9. Monotonic behavior of C and L shaped angle shear connectors within steel-concrete composite beams: an experimental investigation vol.35, pp.2, 2018, https://doi.org/10.12989/scs.2020.35.2.237
  10. Effect of progressive shear punch of a foundation on a reinforced concrete building behavior vol.35, pp.2, 2018, https://doi.org/10.12989/scs.2020.35.2.279
  11. Experimentally and Numerically Investigating the Performances of Aramid Fiber-Reinforced Steel Beams Under Impact Loadings vol.45, pp.10, 2018, https://doi.org/10.1007/s13369-020-04608-1
  12. Influence of porosity and cement grade on concrete mechanical properties vol.10, pp.5, 2018, https://doi.org/10.12989/acc.2020.10.5.393
  13. Effect of shear connectors on strength of structural sandwich panels vol.2, pp.12, 2018, https://doi.org/10.1007/s42452-020-03754-3
  14. Assessment of microstructure and surface effects on vibrational characteristics of public transportation vol.11, pp.1, 2021, https://doi.org/10.12989/anr.2021.11.1.101
  15. Smart estimation of automatic approach in enhancing the road safety under AASHTO Standard specification and STM vol.79, pp.3, 2021, https://doi.org/10.12989/sem.2021.79.3.389
  16. Experimental study of reversal of multidrug resistance in human leukemia K562/DOX cells by toad venom vol.11, pp.2, 2018, https://doi.org/10.12989/anr.2021.11.2.219
  17. Application of multi-hybrid metaheuristic algorithm on prediction of split-tensile strength of shear connectors vol.28, pp.2, 2018, https://doi.org/10.12989/sss.2021.28.2.167
  18. Analyzing shear strength of steel-concrete composite beam with angle connectors at elevated temperature using finite element method vol.40, pp.6, 2018, https://doi.org/10.12989/scs.2021.40.6.853