DOI QR코드

DOI QR Code

A new analytical approach to estimate the seismic tensile force of geosynthetic reinforcement respect to the uniform surcharge of slopes

  • Motlagh, Ali Tafreshi (Faculty of Civil Engineering, Department of Engineering, Kharazmi University) ;
  • Ghanbari, Ali (Faculty of Civil Engineering, Department of Engineering, Kharazmi University) ;
  • Maedeh, Pouyan Abbasi (Institute of Geotechnical Engineering, University of Natural Resources and Life Science) ;
  • Wu, Wei (Institute of Geotechnical Engineering, University of Natural Resources and Life Science)
  • Received : 2018.10.23
  • Accepted : 2018.11.22
  • Published : 2018.12.25

Abstract

This paper investigates the pseudo-static analysis of reinforced slopes with geosynthetics under the influence of the uniform surcharge to evaluate the maximum tensile force of reinforcements. The analytical approach has basically been used to develop the new practical procedure to estimate both tensile force and its distribution in the height of the slope. The base of developed relationships has been adapted from the conventional horizontal slice method. The limit equilibrium framework and the assumptions of log-spiral failure surface have directly been used for proposed analytical approach. A new analytical approach considering a single layer of non-cohesion soil and the influence of uniform surcharge has been extracted from the 5n equation and 5n unknown parameters. Results of the proposed method illustrated that the location of the surcharge, amount of internal friction and the seismic coefficient have the remarkable effect on the tensile force of reinforcement and might be 2 times increasing on it. Furthermore, outcomes show that the amount of tensile force has directly until 2 times related to the amount of slope angle and its height range. Likewise, it is observed that the highest value of the tensile force in case of slope degree more than 60-degree is observed on the lower layers. While in case of less degree the highest amount of tensile force has been reported on the middle layers and extremely depended to the seismic coefficient. Hence, it has been shown that the tensile force has increased more than 6 times compared with the static condition. The obtained results of the developed procedure were compared with the outcomes of the previous research. A good agreement has been illustrated between the amount results of developed relationships and outcomes of previous research. Maximum 20 and 25 percent difference have been reported in cases of static and seismic condition respectively.

Keywords

References

  1. AASHTO (2007), Standard specifications for highway bridges. American Association of State Highway and Transportation Officials, Washington, D.C.
  2. Abbasi Maedeh, P., Ghanbari, A. and Wu, W. (2017), "Estimation of elevated tanks natural period considering fluid- structure- soil interaction by using new approaches", Earthq. Struct., 12(2), 145-152. https://doi.org/10.12989/EAS.2017.12.2.145
  3. Ahmadabadi, M. and Ghanbari, A. (2009), "New procedure for active earth pressure calculation in retaining walls with reinforced cohesive-frictional backfill", Geotext Geomem.., 27(6), 456-463. https://doi.org/10.1016/j.geotexmem.2009.06.004
  4. Allen, T.M., Bathurst, R.J., Lee, W.F., Holtz, R.D., Walters, D.L. (2003), "A new working stress method for prediction of reinforcement loads in geosynthetic walls", Can. Geotech. J., 40(5), 976-994. https://doi.org/10.1139/t03-051
  5. Aminpoor, M.M. and Ghanbari, A. (2014), "Design charts for yield acceleration and seismic displacement of retaining walls with surcharge through limit analysis", Struct. Eng. Mech., 52(6), 1225-1256. https://doi.org/10.12989/SEM.2014.52.6.1225
  6. Ausilio, E., Conte, E. and Dente, G. (2000), "Seismic stability analysis of reinforced slopes", Soil Dyn. Earthq. Eng., 19, 159-172. https://doi.org/10.1016/S0267-7261(00)00005-1
  7. Azad, A., Yasrobi, S. and Pak, A. (2008), "Seismic active earth pressure distribution behind rigid retaining walls", Soil Dyn. Earthq. Eng., 28(5), 365-375. https://doi.org/10.1016/j.soildyn.2007.07.003
  8. Basha, B.M. and Babu, G.L.S. (2011), "Reliability based earthquake resistant design for internal stability of reinforced soil structures", Geotech. Geol. Eng., 29, 803-820. https://doi.org/10.1007/s10706-011-9418-9
  9. Basha, B.M. and Basudhar, P.K. (2010), "Pseudo static seismic stability analysis of reinforced soil structures", Geotech. Geol. Eng., 28, 745-762. https://doi.org/10.1007/s10706-010-9336-2
  10. Bathurst, R.J. and Hatami, K. (1998), "Seismic response analysis of a geosynthetic reinforced soil retaining wall", Geosynth. Int., 5(1-2), 127-166. https://doi.org/10.1680/gein.5.0117
  11. Bathurst, R.J., Allen, T.M. and Walters, D.L. (2005), "Reinforcement loads in geosynthetic walls and the case for a new working stress design method", Geotext. Geomemb., 23(4), 287-322. https://doi.org/10.1016/j.geotexmem.2005.01.002
  12. Caltabiano, S., Cascone, E. and Maugeri, M. (2000), "Seismic stability of retaining walls with surcharge", Soil Dyn. Earthq. Eng., 20(5-8), 469-476. https://doi.org/10.1016/S0267-7261(00)00093-2
  13. Caltabiano, S., Cascone, E. and Maugeri, M. (2011), "Static and seismic limit equilibrium analysis of sliding retaining walls under different surcharge conditions", Soil Dyn. Earthq. Eng., 37, 38-55.
  14. Choudhury, D., Nimbalkar, S.S. and Mandal, J.N. (2007), "External stability of reinforced soil walls under seismic conditions", Geosynth Int., 14(4), 211-218. https://doi.org/10.1680/gein.2007.14.4.211
  15. El-Emam, M.M. and Bathurst, R.J. (2007), "Influence of reinforcement parameters on the seismic response of reducedscale reinforced soil retaining walls", Geotext Geomemb., 25(1), 33-49. https://doi.org/10.1016/j.geotexmem.2006.09.001
  16. Georgiadis, M. and Anagnostopoulos, C. (1998), "Lateral pressure on sheet pile walls due to strip load", J. Geotech. Geoenviron. Eng., 124(1), 95-98. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:1(95)
  17. Gerber, E. (1929), Unter Suchungen Uber Die Druck Verteil Ungimor Lichbel Asteten Sand, Technis che Hochscule, Zurich.
  18. Ghanbari, A. and Ahmadabadi, M. (2010a), "Pseudo-dynamic active earth pressure analysis of inclined retaining walls using horizontal slices method", Scientica Iranica, 17(2), 118-130.
  19. Ghanbari, A. and Ahmadabadi, M. (2010b), "Active earth pressure on inclined retaining walls in static and pseudo-static conditions", Int. J. Civil Eng., 8(2), 159-173.
  20. Ghanbari, A. and Ahmadabadi, M. (2010c), "New analytical procedure for seismic analysis of reinforced retaining wall with cohesive-frictional backfill", Geosynth. Int., 17(6), 364-379 https://doi.org/10.1680/gein.2010.17.6.364
  21. Ghanbari, A. and Taheri, M. (2012), "An analytical method for calculating active earth pressure in reinforced retaining walls subject to a line surcharge", Geotext Geomemb., 34, 1-10. https://doi.org/10.1016/j.geotexmem.2012.02.009
  22. Giri, G. (2011), "Pseudo-dynamic approach of seismic earth pressure behind cantilever retaining wall with inclined backfill surface", Geomech. Eng., 3(4), 255-266 https://doi.org/10.12989/gae.2011.3.4.255
  23. Greco, V.R. (1999), "Active earth thrust on cantilever walls in general conditions", Soil. Found., 39(6), 65-78. https://doi.org/10.3208/sandf.39.6_65
  24. Greco, V.R. (2003), "Pseudo-static analysis for earth thrust computations", Soil. Found., 43(2), 132-140.
  25. Greco, V.R. (2005), "Active earth thrust by backfills subject to a line surcharge", Can. Geotech. J., 42(5), 1255-1263. https://doi.org/10.1139/t05-038
  26. Greco, V.R. (2006), "Lateral earth pressure due to backfill subject to a strip surcharge", Geotech. Geol. Eng., 24, 615-636. https://doi.org/10.1007/s10706-005-2009-x
  27. Hausmann, M.R. and Lee, K.L. (1978), "Rigid model wall with soil reinforcement", Proceedings of Symposium on Earth Reinforcement, ASCE, 400-428.
  28. Huang, C.C. and Luo, W.M. (2010), "Behavior of cantilever and geosynthetic-reinforced walls on deformable foundations", Geotext. Geomemb., 28, 448-459. https://doi.org/10.1016/j.geotexmem.2009.12.008
  29. Huang, C.C. and Wang, W.C. (2005), "Seismic displacement charts for the performance-based assessment of reinforced soil walls", Geosynth Int., 12(4), 176-190. https://doi.org/10.1680/gein.2005.12.4.176
  30. Huang, C.C. and Wu, S.H. (2006), "Simplified approach for assessing seismic displacements of soil retaining walls", Geosynth. Int., 13(6), 219-233. https://doi.org/10.1680/gein.2006.13.6.219
  31. Huang, C.C. and Wu, S.H. (2007), "Simplified approach for assessing seismic displacements of soil-retaining walls. Part II: Geosynthetic-reinforced walls with rigid panel facing", Geosynth. Int., 14(5), 264-276. https://doi.org/10.1680/gein.2007.14.5.264
  32. Huang, C.C., Wu, S.H. and Wu, H.J. (2009), "Seismic displacement criterion for soil retaining walls based on soil strength mobilization", J. Geotech. Geoenviron. Eng., 135(1), 74-83. https://doi.org/10.1061/(ASCE)1090-0241(2009)135:1(74)
  33. Janbu, N. (1957), "Earth pressure and bearing capacity calculations by generalized procedures of slices", Proceedings of 4th International Conference on Soil Mechanics and Foundation Engineering, London.
  34. Jarquio, R. (1981), "Total lateral surcharge pressure due to strip load", J. Geotech. Eng. Div., 107(10), 1424-1428.
  35. Jewell, R.A. (1991), "Application of revised design charts for steep reinforced slopes", Geotext. Geomemb., 10(3), 203-233. https://doi.org/10.1016/0266-1144(91)90056-3
  36. Jones, C.J.F.P. and Clarke, D. (2007), "The residual strength of geosynthetic reinforcement subjected to accelerated creep testing and simulated seismic events", Geotext. Geomemb., 25(2), 155-169. https://doi.org/10.1016/j.geotexmem.2006.12.004
  37. Juran, I., Baudrand, G. and Farrag, K. (1990), "Kinematical limit analysis for design of soil-nailed structures", J. Geotech. Eng., 116(1), 54-72. https://doi.org/10.1061/(ASCE)0733-9410(1990)116:1(54)
  38. Koseki, J., Bathurst, R.J., Guler, E., Kuwano, J. and Maugeri, M. (2006), "Seismic stability of reinforced soil walls", Proceedings of 8th International Conference on Geosynthetics, 51-77.
  39. Laba, J.T. and Kennedy, J.B. (1986), "Reinforced earth retaining wall analysis and design", Can. Geotech. J., 23(3), 317-326. https://doi.org/10.1139/t86-045
  40. Lareal, P., Benameur, F. and Collas, P. (1992), "Active earth pressure reducing perusal: experimental tests", Proceedings of Conference on Retaining Structures, Inst. of Civil Eng., Robinson College, Cambridge.
  41. Leshchinsky, D. (2001), "Design dilemma: use peak or residual strength of soil", Geotext. Geomemb., 19(2), 111-125. https://doi.org/10.1016/S0266-1144(00)00007-8
  42. Leshchinsky, D., Ling, H.I., Wang, J.P., Rosen, A. and Mohri, Y. (2009), "Equivalent seismic coefficient in geocell retention system", Geotext. Geomemb., 27, 9-18. https://doi.org/10.1016/j.geotexmem.2008.03.001
  43. Ling, H.I., Leshchinsky, D. and Mohri, Y. (1997), "Soil slopes under combined horizontal and vertical seismic accelerations", Earthq. Eng. Struct. Dyn., 26, 1231-1241. https://doi.org/10.1002/(SICI)1096-9845(199712)26:12<1231::AID-EQE707>3.0.CO;2-Z
  44. Ling, H.I., Leshchinsky, D. and Perry, E.B. (1997), "Seismic design and performance of geosynthetic-reinforced soil structures", Geotechnique, 47(5), 933-952. https://doi.org/10.1680/geot.1997.47.5.933
  45. Lo, S.C. and Xu, D.W. (1992), "A strain based design method for the collapse limit state of reinforced soil walls and slopes", Can. Geotech. J., 29(8), 832-842. https://doi.org/10.1139/t92-090
  46. Michalowski, R.L. (1997), "Stability of uniformly reinforced slopes", J. Geotech. Geoenviron. Eng., 123(6), 546-556. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:6(546)
  47. Michalowski, R.L. (1998), "Limit analysis in stability calculations of reinforced soil structures", Geotext. Geomemb., 16(6), 311-331. https://doi.org/10.1016/S0266-1144(98)00015-6
  48. Mishra, B. (1980), "Lateral pressures on retaining walls due to loads of surface of granular backfill", Soil. Found., 20(2), 31-44. https://doi.org/10.3208/sandf1972.20.2_31
  49. Moghaddas Tafreshi, S.N., Shaghaghi, T., Tavakoli Mehrjardi, G., Dawson, A.R. and Ghadrdan, M. (2015), "A simplified method for predicting the settlement of circular footings on multilayered geocell-reinforced non-cohesive soils", Geotext. Geomemb., 43(4), 332-344. https://doi.org/10.1016/j.geotexmem.2015.04.006
  50. Mojalla, M. and Ghanbari, A. (2012), "Prediction of seismic displacements in gravity retaining walls based on limit analysis approach", Struct. Eng. Mech., 42(2), 247-267. https://doi.org/10.12989/sem.2012.42.2.247
  51. Mojalla, M., Ghanbari, A. and Askari, F. (2012), "A new analytical method for calculating seismic displacements in reinforced retaining walls", Geosynth. Int., 19(3), 212-231. https://doi.org/10.1680/gein.2012.12.00010
  52. Morgenstern, N.R. and Price, V.E. (1965), "The analysis of the stability of generalized slip surfaces", Geotechnique, 15, 79-93. https://doi.org/10.1680/geot.1965.15.1.79
  53. Motta, E. (1994), "Generalized Coulomb active-earth pressure for distanced surcharge", J. Geotech. Eng., ASCE, 120(6), 1072-1079. https://doi.org/10.1061/(ASCE)0733-9410(1994)120:6(1072)
  54. Nouri, H., Fakher, A. and Jones, C.J.F.P. (2006), "Development of horizontal slices method for seismic stability analysis of reinforced slopes and walls", Geotext. Geomemb., 24, 175-187. https://doi.org/10.1016/j.geotexmem.2005.11.004
  55. Nouri, H., Fakher, A. and Jones, C.J.F.P. (2008), "Evaluating the effects of the magnitude and amplification of pseudo-static acceleration on reinforced soil slopes and walls using the limit equilibrium horizontal slices method", Geotext. Geomemb., 26(3), 263-278. https://doi.org/10.1016/j.geotexmem.2007.09.002
  56. Rankine, W.J.M. (1857), "On the stability of loose earth", Transactions of the Royal Society of London.
  57. Rowe, R.K. and Skinner, G.D. (2001), "Numerical analysis of geosynthetic reinforced retaining wall constructed on a layered soil foundation", Geotext. Geomemb., 19(7), 387-412. https://doi.org/10.1016/S0266-1144(01)00014-0
  58. Sandri, D. (1998), "A performance Summary of reinforced soil structures in the greater Los Angeles area after the Northridge earthquake", Geotext. Geomemb., 15, 235-253.
  59. Saran, S., Garg, K.G. and Bhandari, R.K. (1992), "Retaining wall with reinforced cohesionless backfill", J. Geotech. Eng., ASCE, 118, 1869-1888. https://doi.org/10.1061/(ASCE)0733-9410(1992)118:12(1869)
  60. Sawada, T., Chen, W.F. and Nomachi, S.G. (1993), "Assessment of seismic displacements of slopes", Soil Dyn. Earthq. Eng., 12(3), 357-362. https://doi.org/10.1016/0267-7261(93)90038-S
  61. Segrestin, P. (1992), "Design of sloped reinforced fill structure", Proceedings of Conference on Retaining Structures, Inst. of Civil Eng., Robinson College, Cambridge..
  62. Shahgholi, M., Fakher, A. and Jones, C.J.F.P. (2001), "Horizontal slice method of analysis", Geotechnique, 51(10), 881-885. https://doi.org/10.1680/geot.2001.51.10.881
  63. Shekarian, S., Ghanbari, A. and Farhadi, A. (2008), "New seismic parameters in the analysis of retaining walls with reinforced backfill", Geotext. Geomemb., 26, 350-356. https://doi.org/10.1016/j.geotexmem.2008.01.003
  64. Skinner, G.D. and Rowe, R.K. (2005), "Design and behavior of a geosynthetic reinforced retaining wall and bridge abutment on a yielding foundation", Geotext. Geomemb., 23(3), 234-260. https://doi.org/10.1016/j.geotexmem.2004.10.001
  65. Spangler, M.G. (1938), Horizontal Pressure on Retaining Walls Due to Concentrated Surface Loads, Iowa State University Engineering Experiment Station, Bulletin 140.
  66. Spencer, E. (1967), "A method of analysis of stability of embankments assuming parallel inter-slice forces", Geotechnique, 17(1), 11-26. https://doi.org/10.1680/geot.1967.17.1.11
  67. Tatsuoka, F., Koseki, J., Tateyama, M., Munaf, Y. and Horii, K. (1998), "Seismic stability against high seismic loads of geosynthetic-reinforced soil retaining structures", Proceedings of the 6th International Conference on Geosynthetics, Atlanta.
  68. Tavakoli Mehrjardi, G. and Khazaei, M. (2017), "Scale effect on the behaviour of geogrid-reinforced soil under repeated loads", Geotext. Geomemb., 45(6), 603-615. https://doi.org/10.1016/j.geotexmem.2017.08.002
  69. Tavakoli Mehrjardi, G. and Motarjemi, F. (2018), "Interfacial properties of geocell-reinforced granular soils", Geotext. Geomemb., 46(4), 384-395. https://doi.org/10.1016/j.geotexmem.2018.03.002
  70. Tavakoli Mehrjardi, G., Ghanbari, A. and Mehdizadeh, H. (2016), "Experimental study on the behaviour of geogridreinforced slopes with respect to aggregate size", Geotext. Geomemb., 44(6), 862-871. https://doi.org/10.1016/j.geotexmem.2016.06.006
  71. Wihelm Ernest and Sohn (2002), Beton Kalendar, Verlag von Wihelm Ernest and Sohn, Munich, Germany.
  72. Yamagami, T., Jiang, J. and Ahmed Khan, Y. (1999), "Progressive failure analysis based on a method of no-vertical slices", Proceedings of Slope Stability Engineering, 2.
  73. Zornberg, J.G., Sitar, N. and Mitchel, J.K. (1998b), "Performance of geosynthetic reinforced slopes at failure", J. Geotech. Geoenviron. Eng., 124(8), 670-683. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:8(670)
  74. Zornberg, J.G., Sitar, N. and Mitchell, J.K. (1998a), "Limit equilibrium as basis for design of geosynthetic-reinforced slopes", J. Geotech. Eng., 124(8), 684-698. https://doi.org/10.1061/(ASCE)1090-0241(1998)124:8(684)

Cited by

  1. Numerical investigation of geocell reinforced slopes behavior by considering geocell geometry effect vol.24, pp.6, 2018, https://doi.org/10.12989/gae.2021.24.6.589
  2. Modified pseudo-dynamic analysis of rigid gravity retaining wall with cohesion-less backfill and uniform surcharge vol.26, pp.5, 2018, https://doi.org/10.12989/gae.2021.26.5.453