References
- Shim, J. H., Yun, W. S. and Ko, T. J., “Successful Examples of 3D Printing Technology-based Start-up Enterprises,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 15, No. 2, pp. 104-110, 2016. https://doi.org/10.14775/ksmpe.2016.15.2.104
- Choi, J. W. and Kim, H. C., “3D Printing Technologies - A Review,” Journal of the Korean Society of Manufacturing Process Engineers, Vol. 14, No. 3, pp. 1-8, 2015. https://doi.org/10.14775/ksmpe.2015.14.3.001
- Wohler, T., Wohler's report 2017, Wohler Associates, 2017.
- Syed, W. U. H., Pinkerton, A. J., and Li, L., "A Comparative Study of Wire Feeding and Powder Feeding in Direct Diode Laser Deposition for Rapid Prototyping," Applied Surface Science, Vol. 247, Nos. 1-4, pp. 268-276, 2005. https://doi.org/10.1016/j.apsusc.2005.01.138
- Mok, S. H., Bi, G., Folkes, J., and Pashby, I., “Deposition of Ti-6AL-4V Using a High Power Diode Laser and Wire, Part I: Investigation on the Process Characteristics,” Surface and Coatings Technology, Vol. 202, No. 16, pp. 3933-3939, 2008. https://doi.org/10.1016/j.surfcoat.2008.02.008
- Abioye, T., Folkes, J., and Clare, A., “A Parametric Study of Inconel 625 Wire Laser Deposition,” Journal of Materials Processing Technology, Vol. 213, No. 12, pp. 2145-2151, 2013. https://doi.org/10.1016/j.jmatprotec.2013.06.007
- Hagqvist, P., Heralic, A., Christiansson, A.-K., and Lennartson, B., "Resistance Measurements for Control of Laser Metal Wire Deposition," Optics and Lasers in Engineering, Vol. 54, pp. 62-67, 2014. https://doi.org/10.1016/j.optlaseng.2013.10.010
- Miranda, R., Lopes, G., Quintino, L., Rodrigues, J., and Williams, S., “Rapid Prototyping with High Power Fiber Lasers,” Materials & Design, Vol. 29, No. 10, pp. 2072-2075, 2008. https://doi.org/10.1016/j.matdes.2008.03.030
- Kim, J. G. and Lee. C. W., “Laser Assisted Additive Manufacturing by Rotating Metal Wire Feeder,” J. Korean Soc. Precis. Eng., Vol. 35, No. 9, pp. 848, 2018.
- Lee, S. Y., Lee, I. K., Lee, J. W., Lee, S. B. and Lee, S. K., "Evaluation of Wear Characteristics of AISI H13 ToolSteel Repaired by Metal 3D Printing," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 4, p. 10, 2017.
- Olioul, I. M. and Kim, H. C., "An Algorithm for the Removing of Offset Loop Twists during the Tool Path Generation of FDM 3D Printer," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 3, p. 3, 2017.
- Kang, Y. G, Lee, T. W. and Shin, G. S., "The Influence of Experiment Variables on 3D Printing using ABS Resin," Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 2, p. 96, 2017. https://doi.org/10.14775/ksmpe.2016.16.1.096