Design & Manufacturing

  • 제12권3호
  • /
  • Pages.55-59
  • /
  • 2018
  • /
  • 2800-0323(pISSN)
  • /
  • 2733-452X(eISSN)
한국금형공학회 (Korean Society of Die & Mold Engineering)
권호 표지

사출성형해석 연구를 이용한 게이트 밸런스 계산식의 검증

Verification of gate balancing equation using injection molding analysis

  • 한성렬 (국립공주대학교 금형설계공학과)
  • Han, Seong-Ryeol (Department of Metalmold Design Engineering, Kongju National University)
  • 투고 : 2018.10.23
  • 심사 : 2018.12.01
  • 발행 : 2018.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

In a multi-cavity mold having a runner layout of a fish bone structure, problems of unbalanced filling between cavities occur constantly. Unbalanced charging lowers the dimensional accuracy of a molded article and causes deformation after molding. To solve this problem, the gate size connected to each cavity is adjusted using the BGV (Balanced Gate Value) equation. In this paper, in order to solve the filling imbalance problem of the runner layout mold of fish bone structure through injection molding analysis study, we compared the charging imbalance phenomenon before and after improvement after adjusting the gate size by applying BGV equation. From the results of the molding analysis, the shrinkage ratio before and after the improvement of the molded article was improved by only about 0.08%. Based on these results, it was confirmed that the charging imbalance problem was not significantly improved even when the BGV equation was applied.

키워드

참고문헌

  1. Wang, M.L., Chang, R.Y. and Hsu, C.H., "Molding Simulation Theory and Practice", Hanser, pp. 220-224, 2018.
  2. Kang, C.M. and Jeong, Y.D., "Effects of Processing Factors on Filling Imbalances in Multi-cavity Injection Mold", Proceedings of the Korean Society for Technology of Plasticity 2004 Autumn Conference, pp. 54-57, 2004.
  3. Beaumont, J.P. and Young, J.H., "Mold Filling Imbalances in Geometrically Balanced Runner systems.", Journal of Injection Molding Technology, vol 1, No. 3, pp. 133-135, 1997.
  4. Kwon, Y.S. and Jeong, Y.D., "Optimization of Processing on Filling Balance of the HR3P Mold Structure", Vol. 26, No. 3, pp. 98-102, 2009.
  5. Je, D.K. and Jeong, Y.D., "Filling Imbalance in 3 plate Type Injection Molds with Multi-Cavity", Vol. 21, No. 6, pp. 117-121, 2004.
  6. Jeong, Y.D. and Jang, M.K., "A New Runner System Melt-Buffer for Filling Balance in Injection Mold", Vol. 18, No. 2, pp. 122-127, 2009.
  7. Lim S.H., "Injection Mold Design", Boseongkak, pp. 173-175, 2011.
  8. Beaumont, J.P., "Runner and Gating Design Handbook", Hanser, pp. 142-143, 2004.
  9. Han, S.R., "A Study on the Deformation Optimization of a Plastic Bezel Assembled on the Steering Wheel of an Automobiles", Journal of the Korean Society of Manufacturing Process Engineers, Vol. 16, No. 5, pp. 105-112, 2017. https://doi.org/10.14775/ksmpe.2017.16.5.105