Structural Engineering and Mechanics

  • 제63권5호
  • /
  • Pages.669-681
  • /
  • 2017
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Analysis of R/C frames considering cracking effect and plastic hinge formation

  • Kara, Ilker Fatih (Civil Engineering Department, Bursa Technical University) ;
  • Ashour, Ashraf F. (School of Engineering, Faculty of Engineering and Informatics, University of Bradford) ;
  • Dundar, Cengiz (Civil Engineering Department, Cukurova University)
  • 투고 : 2017.02.21
  • 심사 : 2017.06.07
  • 발행 : 2017.09.10
⟨ 이전 논문 다음 논문 ⟩

초록

The design of reinforced concrete buildings must satisfy the serviceability stiffness criteria in terms of maximum lateral deflections and inter story drift in order to prevent both structural and non-structural damages. Consideration of plastic hinge formation is also important to obtain accurate failure mechanism and ultimate strength of reinforced concrete frames. In the present study, an iterative procedure has been developed for the analysis of reinforced concrete frames with cracked elements and consideration of plastic hinge formation. The ACI and probability-based effective stiffness models are used for the effective moment of inertia of cracked members. Shear deformation effect is also considered, and the variation of shear stiffness due to cracking is evaluated by reduced shear stiffness models available in the literature. The analytical procedure has been demonstrated through the application to three reinforced concrete frame examples available in the literature. It has been shown that the iterative analytical procedure can provide accurate and efficient predictions of deflections and ultimate strength of the frames studied under lateral and vertical loads. The proposed procedure is also efficient from the viewpoint of computational time and convergence rate. The developed technique was able to accurately predict the locations and sequential development of plastic hinges in frames. The results also show that shear deformation can contribute significantly to frame deflections.

키워드

참고문헌

  1. American Concrete Institute (ACI) (2014), Building code requirements for reinforced concrete (ACI 318-14), Farmington Hills, Michigan.
  2. Al-Mahaidi R.S.H. (1978), "Nonlinear finite element analysis of reinforced concrete deep members", Department of Struct. Engrg. Cornell University, Report No: 79-1, 357.
  3. Babazadeh, A., Burgueno, R. and Silva, P.F. (2016), "Evaluation of the critical plastic region length in slender reinforced concrete bridge columns", Eng. Struct., 125, 280-293. https://doi.org/10.1016/j.engstruct.2016.07.021
  4. Bae, S. and Bayrak, O. (2008), "Plastic hinge length of reinforced concrete columns", ACI Struct. J., 105(3), 290-300.
  5. Barrera, A.C., Bonet, J.L., Romero, M.L. and Miguel, P.F. (2011), "Experimental tests of slender reinforced concrete columns under combined axial load and lateral force", Eng. Struct., 33(12), 3676-3689. https://doi.org/10.1016/j.engstruct.2011.08.003
  6. Berzegar, F. (1989), "Analysis of reinforced concrete membrane elements with anisotropic reinforcement", J. Struct. Eng., ASCE, 115(3), 647-665. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:3(647)
  7. Branson, D.E. (1963), "Instantaneous and time-dependent deflections of simple and continuous reinforced concrete beams, HPR", Alabama Highway Deparment/US Bureau of Public Roads, Report No. 7(1), 78.
  8. Bratina, S., Saje, M. and Planinc, I. (2004), "On materially and geometrically nonlinear analysis of reinforced concrete planar frames", Int. J. Solid. Struct., 41, 7181-7207. https://doi.org/10.1016/j.ijsolstr.2004.06.004
  9. Chan, C.M., Ning, F. and Mickleborough, N.C. (2000), "Lateral stiffness characteristics of tall reinforced concrete buildings", Struct. Des. Tall Build., 9, 365-383. https://doi.org/10.1002/1099-1794(200012)9:5<365::AID-TAL158>3.0.CO;2-B
  10. Chen, W.F. (1982), Plasticity in Reinforced Concrete, McGraw- Hill, New York.
  11. Comite Euro-International du Beton (1985), Manual on Cracking and Deformation, Bulletin d'Information, 158-E.
  12. Cosenza, E. (1990), "Finite element analysis of reinforced concrete elements in a cracked state", Comput. Struct., 36(1), 71-79. https://doi.org/10.1016/0045-7949(90)90176-3
  13. Dadi, S.K.V. and Agarwal, P. (2015), "Effect of types of reinforcement on plastic hinge rotation parameters of RC beams under pushover and cyclic loading", Earthq. Eng. Eng. Vib., 14(3), 503-516. https://doi.org/10.1007/s11803-015-0040-3
  14. Dundar, C. and Kara, I.F. (2007), "Three dimensional analysis of reinforced concrete frames with cracked beam and column elements", Eng. Struct., 29(9), 2262-2273. https://doi.org/10.1016/j.engstruct.2006.11.018
  15. Ernst, G.C., Smith, G.M., Riveland, A.R. and Pierce, D.N. (1973), "Basic reinforced concrete frame performance under vertical and lateral loads", ACI J., 70, 261-269.
  16. Elmenshawi, A., Brown, T. and El-Metwally, S. (2012), "Plastic hinge length considering shear reversal in reinforced concrete elements", J. Earthq. Eng., 16(2), 188-210. https://doi.org/10.1080/13632469.2011.597485
  17. Ersoy, U. and Ozcebe, G. (2014), Reinforced Concrete Construction, Evrim Publications, Ankara.
  18. Ingraffea, A.R. and Grestle, W. (1985), "Non-linear fracture models for discrete crack propagation", Applications of Fracture Mechanics to Cementitious Composites, Ed. Shah, S.P., The Hague, Martinus-Nijhoff, The Netherlands.
  19. Nilson, A.H. (1967), "Nonlinear analysis of reinforced concrete by the finite element method", ACI Struct. J., 65(9), 757-766.
  20. Ning, C.L. and Li, B. (2016), "Probabilistic approach for estimating plastic hinge length of reinforced concrete columns", J. Struct. Eng., 142(3), 1-15.
  21. Kara, I.F. and Dundar, C. (2009), "Prediction of deflection of reinforced concrete shear walls", Adv. Eng. Softw., 40(9), 777-785. https://doi.org/10.1016/j.advengsoft.2009.02.002
  22. Karthiga, S.N., Preetha, V. and Jayaraman, A. (2014), "Finite element analysis of reinforced concrete frames", Int. J. Innov. Res. Adv. Eng., IJIRAE, 1(8), 272-285.
  23. Kwak, H.G. and Song, J.Y. (2002), "Cracking analysis of RC members using polynomial strain distribution function", Eng. Struct., 24, 455-468. https://doi.org/10.1016/S0141-0296(01)00112-2
  24. Kwak, H.G. and Kim, D.Y. (2004), "Material nonlinear analysis of RC shear walls subject to monotonic loading", Eng. Struct., 26, 1517-1533. https://doi.org/10.1016/j.engstruct.2004.05.013
  25. Lopez, A.L, Tomas, A. and Olivares, G. (2016), "Influence of adjusted models of plastic hinges in nonlinear behaviour of reinforced concrete buildings", Eng. Struct., 124, 245-257. https://doi.org/10.1016/j.engstruct.2016.06.021
  26. Lopez-Lopez, A., Tomas, A. and Sanchez-Olivares, G. (2016), "Behaviour of reinforced concrete rectangular sections based on tests complying with seismic construction requirements", Struct. Concrete, 17(4), 656-67. https://doi.org/10.1002/suco.201500107
  27. Polak, M.A. (1995), "Effective stiffness model for reinforced concrete slabs", J. Struct. Eng., ASCE, 122(9), 1025-1030. https://doi.org/10.1061/(ASCE)0733-9445(1996)122:9(1025)
  28. Sakai, K. and Kakuta, Y. (1980), "Moment-curvature relationship of reinforced concrete members subjected to combined bending and axial force", ACI J., 77, 189-194.
  29. Spiliopoulos, K.V. and Lykidis, G.C. (2006), "An efficient threedimensional solid finite element dynamic analysis of reinforced concrete structures", Earth. Eng. Struct. Dyn., 35, 137-157. https://doi.org/10.1002/eqe.510
  30. Stramandinoli, R.S.B. and Rovere, H.L.L. (2008), "An efficient tension-stiffening model for nonlinear analysis of reinforced concrete members", Eng. Struct., 30, 2069-2080. https://doi.org/10.1016/j.engstruct.2007.12.022
  31. Tang, Z., Ma, H., Guo, J., Xie, Y. and Li, Z. (2016), "Experimental research on the propagation of plastic hinge length for multiscale reinforced concrete columns under cyclic loading", Earthq. Struct., 11(5), 823-840. https://doi.org/10.12989/eas.2016.11.5.823
  32. Tanrikulu, A.K., Dundar, C. and Cagatay, I.H. (2000), "Computer program for the analysis of reinforced concrete frames with cracked beam elements", Struct. Eng. Mech., 10(5), 463-478. https://doi.org/10.12989/sem.2000.10.5.463
  33. Vecchio, F.J., Emara, M.B. (1992), "Shear deformations in reinforced concrete frames", ACI Struct. J., 89(1), 46-56.
  34. Wang, T. and Hsu, T.T.C. (2001), "Nonlinear finite element analysis of concrete structures using new constitutive models", Comput. Struct., 79, 2781-2791. https://doi.org/10.1016/S0045-7949(01)00157-2
  35. Yang, K., Shi, Q.X. and Zhao, J.H. (2013), "Plastic hinge length of high strength concrete columns confined by high strength stirrups", Eng. Mech., 30(2), 254-259.
  36. Yuzugullu, O. and Schnobrich, W.C. (1973), "A numerical procedure for the determination of the behaviour of a shear wall frame system", ACI J., 70(7), 474-479.
  37. Zhao, X.M., Wu, Y.F. and Leung, A.Y.T. (2012), "Analyses of plastic hinge regions in reinforced concrete beams under monotonic loading", Eng. Struct., 34, 466-482. https://doi.org/10.1016/j.engstruct.2011.10.016

피인용 문헌

  1. SSI effects on the redistribution of seismic forces in one-storey R/C buildings vol.20, pp.3, 2021, https://doi.org/10.12989/eas.2021.20.3.261