DOI QR코드

DOI QR Code

Shear behavior of RC beams externally strengthened and anchored with CFRP composites

  • Al-Rousan, Rajai Z. (Department of Civil Engineering, Jordan University of Science and Technology)
  • 투고 : 2017.01.04
  • 심사 : 2017.05.13
  • 발행 : 2017.08.25

초록

The primary objective of this paper is to study the effectiveness of anchorage on the performance of shear deficient beams externally strengthened with CFRP composites. The overall behavior of the tested beams loaded up to failure, the onset of the cracking, and crack development with increased load and ductility were described. The use of CFRP composites is an effective technique to enhance the shear capacity of RC beams by using CFRP strips anchored into the tension side and from the top by 15-34% based on the investigated variables. Bonded anchorage of CFRP strips with width of 0.1h-0.3h to the beam resulted in a decrease in average interface bond stress and an increase in the effective strain of the FRP sheet at failure, which resulted in a higher shear capacity as compared with that of the U-wrapped beams without anchorage as well as delay or mitigate the sheet debonding from the concrete surface.

키워드

과제정보

연구 과제 주관 기관 : Jordan University of Science and Technology

참고문헌

  1. ACI Committee 440 (2008), "Guide for the Design and Construction of Externally Bonded FRP Systems for strengthening Concrete Structures", ACI440.2R-08, American Concrete Institute; Farmington Hills, Mich.
  2. Bianco, V., Barros, J.A.O. and Monti, G. (2010), "New approach for modeling the contribution of NSM FRP strips for shear strengthening of RC beams", J. Compos. Constr., 14(1), 36-48. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000048
  3. Bilotta, A., Ceroni, F., Di Ludovico, M., Nigro, E., Pecce, M. and Manfredi, G. (2011), "Bond efficiency of EBR and NSM FRP systems for strengthening concrete members", J. Compos. Constr., 15(5), 757-772. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000204
  4. Bousselham, A. and Chaallal, O. (2006), "Behaviour of reinforced concrete T-beams strengthened in shear with carbon fiberreinforced polymer-an experimental study", ACI Struct. J., 103(3), 339-347.
  5. Bousselham, A. and Chaallal, O. (2008), "Mechanisms of Shear Resistance of Concrete Beams strengthened in shear with externally bonded FRP", J. Compos. Constr., 12(5), 499-512. https://doi.org/10.1061/(ASCE)1090-0268(2008)12:5(499)
  6. Bukhari, I.A., Vollum, R.L., Ahmad, S. and Sagaseta, J. (2010), "Shear strengthening of reinforced concrete beams with CFRP", Mag. Concrete Res., 62(1), 65-77. https://doi.org/10.1680/macr.2008.62.1.65
  7. Cao, S.Y., Chen, J.F., Teng, J.G., Hao, Z. and Chen, J. (2005), "Debonding of RC beams shear strengthened with complete FRP wraps", J. Compos. Constr., 9(5), 417-428. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:5(417)
  8. Ceroni, F. (2010), "Experimental performances of RC beams strengthened with FRP materials", Constr. Build. Mater., 24(1), 1547-1559. https://doi.org/10.1016/j.conbuildmat.2010.03.008
  9. Chaallal, O., Mofidi, A., Benmokrane, B. and Neale, K. (2011), "Embedded through-section FRP rod method for shear strengthening of RC beams: performance and comparison with existing techniques", J. Compos. Constr., 15(3), 732-742. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000219
  10. Chaallal, O., Nollet, M.J. and Perraton, D. (1998), "Shear strengthening of RC beams by externally bonded side CFRP strips", J. Compos. Constr., 2(2), 111-113. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:2(111)
  11. Chen, J.F. and Teng, J.G. (2003), "Shear capacity of FRPstrengthened RC beams: FRP debonding", Constr. Build. Mater., 17(1), 27-41. https://doi.org/10.1016/S0950-0618(02)00091-0
  12. Colotti, V., Spadea, G. and Swamy, R.N. (2004), "Structural Model to Predict the Failure Behavior of Plated Reinforced Concrete Beams", J. Compos. Constr., 8(2), 104-122. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:2(104)
  13. Deniaud, C. and Cheng, J.J.R. (2001), "Shear behaviour of reinforced concrete T-beams with externally bonded fiberreinforced polymer sheets", ACI Struct. J., 98(3), 386-394.
  14. Dias, S.J.E. and Barros, J.A.O. (2011), "Shear strengthening of RC T-section beams with low strength concrete using NSM CFRP laminates", Cement Concrete Compos., 33(2), 334-345. https://doi.org/10.1016/j.cemconcomp.2010.10.002
  15. Dias, S.J.E. and Barros, J.A.O. (2012), "NSM shear strengthening technique with CFRP laminates applied in high-strength concrete beams with or without pre-cracking", Compos. Part B: Eng., 43(2), 290-301. https://doi.org/10.1016/j.compositesb.2011.09.006
  16. Dias, S.J.E. and Barros, J.A.O. (2013), "Shear strengthening of RC beams with NSM CFRP laminates: experimental research and analytical formulation", Compos. Struct., 99(1), 477-490. https://doi.org/10.1016/j.compstruct.2012.09.026
  17. Galal, K. and Mofidi, A. (2010), "Shear strengthening of RC Tbeams using mechanicallyanchored unbonded dry carbon fibre sheets", ASCE, J. Perform. Constr. Facil., 24(1), 31-39. https://doi.org/10.1061/(ASCE)CF.1943-5509.0000067
  18. Hojatkashani, A. and Kabir, M.Z. (2012), "Interfacial stress assessment at the cracked zones in CFRP retrofitted RC beams", Struct. Eng. Mech., 44(6), 12-23.
  19. Hosen, M.A., Jumaat, M.Z., Islam, A.B.M.S., Kamruzzaman, M., Huda, M.N. and Soeb, M.R. (2015), "Eliminating concrete cover separation of NSM strengthened beams by CFRP end anchorage", Struct. Eng. Mech., 56(6), 36-47.
  20. Jayaprakash, J., Samad, A.A.A., Abbasovich, A.A. and Ali, A.A. A. (2007), "Repair of precracked RC rectangular shear beams using CFRP strip technique", Struct. Eng. Mech., 26(2), 54-63.
  21. Khalifa, A. and Nanni, A. (2000), "Improving shear capacity of existing RC T-section beams using CFRP composites", Cement Concrete Compos., 22(1), 165-174. https://doi.org/10.1016/S0958-9465(99)00051-7
  22. Khalifa, A. and Nanni, A. (2002), "Rehabilitation of rectangular simply supported RC beams with shear deficiencies using CFRP composites", Constr. Build. Mater., 16(3), 135-146. https://doi.org/10.1016/S0950-0618(02)00002-8
  23. Khalifa, A., Gold, W.J., Nanni, A, and Aziz, A., (1998), "Contribution of externally bonded FRP to shear capacity of RC flexural members", J. Compos. Constr., 2(2), 195-201. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:4(195)
  24. Lee, H.K., Cheong, S.H., Ha, S.K. and Lee, C.G. (2011), "Behaviour and performance of RC T-section deep beams externally strengthened in shear with CFRP sheets", J. Compos. Struct., 93(1), 911-922. https://doi.org/10.1016/j.compstruct.2010.07.002
  25. Lee, H.K., Ha, S.K. and Afzal, M. (2008), "Finite element analysis of shear-deficient RC beams strengthened with CFRP strips/sheets", Struct. Eng. Mech., 30(2), 33-44.
  26. Li, A., Assih, J. and Delmas, Y. (2001), "Shear strengthening of RC beams with externally bonded CFRP sheets", J. Struct. Eng., 127(4), 280-374. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:3(280)
  27. Martinola, G., Meda, A., Plizzari, G.A. and Rinaldi, Z. (2010), "Strengthening and repair of RC beams with fiber reinforced concrete", Cement Concrete Compos., 32(1), 731-739. https://doi.org/10.1016/j.cemconcomp.2010.07.001
  28. Mofidi, A., Chaallal, O., Benmokrane, B. and Neale, K. (2012), "Performance of end-anchorage systems for RC Beams strengthened in shear with epoxy bonded FRP", J. Compos. Struct., 16(3), 322-331.
  29. Mosallam, A.S. and Banerjee, S. (2007), "Shear enhancement of reinforced concrete beams strengthened with FRP composite laminates", Compos. Part B; 38(1), 781-193. https://doi.org/10.1016/j.compositesb.2006.10.002
  30. Ozgur, A., Bulut, N. and Ayhan, M. (2012), "Strain distribution between CFRP strip and concrete at strengthened RC beam against shear", Struct. Eng. Mech., 41(4), 42-51.
  31. Pannirselvam, N., Nagaradjane, V. and Chandramouli, K. (2009), "Strength behaviour of fiber reinforced polymer strengthened beams", ARPN J. Eng. Appl. Sci., 4(9), 34-39.
  32. Pellegrino, C. and Modena, C. (2002), "Fiber reinforced polymer shear strengthening of reinforced concrete beams with transverse steel reinforcement", J. Compos. Constr., 6(2), 104-111. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(104)
  33. Sato, Y., Katsumata, H. and Kobatake, Y. (1997), "Shear strengthening of existing reinforced concrete beams by CFRP sheet", Proc. of the 3rd Int. Symp. on Non-Metallic (FRP) Reinforcement for Concrete Structures, Sapporo, Japan.
  34. Schuman, P. (2004), "Mechanical anchorage for shear rehabilitation of reinforced concrete structures with FRP: an appropriate design approach", Ph.D. Thesis. University of California. San Diego.
  35. Seo, S., Feo, L. and Hui, D. (2013), "Bond strength of near surface-mounted FRP plate for retrofit of concrete structures", Compos. Struct., 95(1), 719-727. https://doi.org/10.1016/j.compstruct.2012.08.038
  36. Shuraim Ahmed, B. (2011), "Efficacy of CFRP configurations for shear of RC beams: experimental and NLFE", Struct. Eng. Mech., 39(3), 23-34.
  37. Siddiqui, N.A. (2009), "Experimental investigation of RC beams strengthened with externally bonded FRP composites", Lat. Am. J. Solid. Struct., 6(1), 343-362.
  38. Sundarraja, M.C. and Rajamohan, S. (2009), "Strengthening of RC beams in shear using GFRP inclined strips-an experimental study", Constr. Build. Mater., 23(1), 856-864. https://doi.org/10.1016/j.conbuildmat.2008.04.008
  39. Taljsten, B. (2003), "Strengthening concrete beams for shear with CFRP sheets", Constr. Build. Mater., 17(1), 15-26. https://doi.org/10.1016/S0950-0618(02)00088-0
  40. Teng, J.G., Lam, L. and Chen, J.F. (2004), "Shear strengthening of RC beams with FRP composites", Prog. Struct. Eng. Mater., 6(1), 173-184. https://doi.org/10.1002/pse.179
  41. Triantafillou, T.C. (1998), "Shear strengthening of reinforced concrete beams using epoxy bonded FRP composites", ACI Struct. J., 95(2), 107-115.
  42. Valerio, P., Bell, T.J. and Darby, A.P. (2009), "Deep embedment of FRP for concrete shear strengthening", Proc ICE-Struct. Build., 162(5), 311-321. https://doi.org/10.1680/stbu.2009.162.5.311
  43. Zhang, Z. and Hsu, C.T.T. (2005), "Shear strengthening of reinforced concrete beams using carbon-fiber reinforced polymer laminates", J. Compos. Constr., 9(3), 158-69. https://doi.org/10.1061/(ASCE)1090-0268(2005)9:2(158)

피인용 문헌

  1. PVC and POM gripping mechanisms for tension testing of FRP bars vol.77, pp.1, 2021, https://doi.org/10.12989/sem.2021.77.1.075