한국지진공학회논문집 (Journal of the Earthquake Engineering Society of Korea)

  • 제21권4호
  • /
  • Pages.197-204
  • /
  • 2017
  • /
  • 1226-525X(pISSN)
  • /
  • 2234-1099(eISSN)
한국지진공학회 (Earthquake Engineering Society of Korea)
권호 표지
DOI QR코드

DOI QR Code

고강도 강재를 활용한 초고층건물의 경제성 및 적합성 분석

Analysis of Economic Feasibility and Suitability of Highrise Buildings Using Highstrength Steel

  • 김선웅 (영산대학교 건축플랜트학과)
  • Kim, Seonwoong (Department of Architecture and Plant Engineering, Youngsan University)
  • 투고 : 2017.06.19
  • 심사 : 2017.06.21
  • 발행 : 2017.07.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

This paper aims to analyze the economic feasibility and investigate the possibility of elastic seismic design of wind-designed highrise concentrically braced frames considering change of mechanical properties of Korean steel under the strong wind and the low seismicity in Korea. To this end, first, highrise concentrically braced frames were designed considering strong wind load. And then, analyses of the economics of them were performed. The seismic performance evaluation of wind-designed highrise buildings was conducted using the response spectrum analysis procedure. Analysis results show that it is possible to save up to approximately 90% of the amount of steel on the 10% increase in steel strength without serviceability. However, with serviceability, the design sectional area of the steel with relatively high strength tends to increment considerably because of the lateral stiffness due to reduction of the inertia moment and so on. This point might apply to limitation of the steel with high tensile yield strength.

키워드

참고문헌

  1. Lee CH, Kim S. Elastic Seismic Deisng of Steel High-rise Buildings in Regions of Strong Wind and Moderate Seismicity. International Journal of Steel Structures. 2007 Dec;7(4):253-261. https://doi.org/10.12989/scs.2007.7.3.253
  2. Kim S, Lee K. Seismic performance of wind-designed diagrid tall steel buildings in regions of moderate seismicity and strong wind. Steel and Composite Structures. 2013 Feb;14(2): 155-171. https://doi.org/10.12989/scs.2013.14.2.155
  3. Kim S, Lee K. Potentials of elastic seismic design of twisted highrise steel diagrid frames. Steel and Composite Structures. 2015 Jan;18(1):121-134. https://doi.org/10.12989/scs.2015.18.1.121
  4. Korean Agency for Technology and Standards (KATS). Rolled steel for welded structure: KS D 3515. KATS. 2016.
  5. Architectural Institute of Korea (AIK). Korean Building Code and Commentary 2016. AIK. 2016.
  6. American Society of Civil Engineers (ASCE). Minimum Design Loads for Buidings and Other Structures: ASCE 7-10. ASCE. c2010.
  7. National Building Code of Canada (NBCC). User's Guide-NBC 2005 Structural Commentaries (Part 4 of Division B): NBCC 2005. c2005.
  8. MIDAS Genw. General Structure Design System for Windows. MIDASIT. c2010.
  9. Council on Tall Buildings and Urban Habitat (CTBUH). Recommendations for the Seismic Design of Highrise Buildings. CTBUH. c2008.
  10. Los Angeles Tall Buildings Structural Design Council (LATBSDC). An alternative procedure for seismic analysis and design of tall buildings located in the Los Angeles region: consensus document. LATBSDC. c2011.
  11. Pacific Earthquake Engineering Research Center (PEER). Tall Buildings Initiative Guidelines for Performance-Based Seismic Design of Tall Buildings: Report No. 2010/05. PEER. c2010.
  12. Satake N, Suda K, Arakawa T, Sadaki K, Tamura Y. Damping evaluation using full scale data of buildings in Japan. Journal of Structural Engineering. 2003;129(4):470-477. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:4(470)
  13. Tamura Y. Amplitude dependency of damping in buildings and estimation techniques. Proceedings of 12th AWES Wind Engineering Workshop; Queentown, New Zealand; c2006.
  14. American Society of Civil Engineers (ASCE). Seismic Evaluation and Retrofit of Existing Buildings: ASCE 41-13. ASCE. c2014.