DOI QR코드

DOI QR Code

Uniaxial bond stress-slip behavior of reinforcing bars embedded in lightweight aggregate concrete

  • Tang, Chao-Wei (Department of Civil Engineering & Geomatics, Cheng Shiu University)
  • 투고 : 2016.09.07
  • 심사 : 2017.02.10
  • 발행 : 2017.06.10

초록

This paper presents an experimental study of bond-slip behavior of reinforced lightweight aggregate concrete (LC) and normal weight concrete (NC) with embedded steel bar. Tests were conducted on tension-pull specimens that had cross-sectional dimension with a reinforcing bar embedded in the center section. The experimental variables include concrete strength (20, 40, and 60 MPa) and coarse aggregate type (normal-weight aggregate and reservoir sludge lightweight aggregate). The test results show that as concrete compressive strength increased, the magnitudes of the slip of the LC specimens were greater than those of the NC specimens. Moreover, the bond strength and stiffness approaches zero at the loaded end, or close to the central anchored point of the specimen. In addition, the proposed bond stress-slip equation can effectively estimate the behavior of bond stress and steel bar slipping.

키워드

참고문헌

  1. ACI Committee 224 (1992), Cracking of Concrete Members in Direct Tension (ACI 224.2R-92), American Concrete Institute, Farmington Hills, Mich.
  2. ACI Committee 318 (2014), Building Code Requirements for Structural Concrete (ACI 318-14) and Commentary, American Concrete Institute, Farmington Hills, Mich.
  3. ACI Committee 408 (2003), Bond and Development of Straight Reinforcing Bars in Tension (ACI 408R-03). American Concrete Institute, Farmington Hills, Mich.
  4. ASTM C150/C150M-15 (2015), Standard Specification for Portland Cement, ASTM International, West Conshohocken, PA, www.astm.org.
  5. ASTM C33/C33M-13 (2013), Standard Specification for Concrete Aggregates, ASTM International, West Conshohocken, PA,www.astm.org.
  6. Basche, H.D., Rhee, I., Willam, K.J. and Shing, P.B. (2007), "Analysis of shear capacity of lightweight concrete beams", Eng. Fracture Mech., 74(1-2), 179-193. https://doi.org/10.1016/j.engfracmech.2006.01.012
  7. CEB (2010), CEB-FIP Model Code 2010, Lausanne, Switzerland.
  8. Chen, H.J., Tsai, W.P., Tang, C.W. and Liu, T.H. (2011a), "Timedependent properties of lightweight concrete using sedimentary lightweight aggregate and its application in prestressed concrete beam", Struct. Eng. Mech., 39(6), 833-847. https://doi.org/10.12989/sem.2011.39.6.833
  9. Chen, H.J., Liu, T.H., Tang, C.W. and Tsai, W.P. (2011b), "Influence of high-cycle fatigue on the tension stiffening behavior of flexural reinforced lightweight aggregate concrete beams", Struct. Eng. Mech., 40(6), 847-866. https://doi.org/10.12989/sem.2011.40.6.847
  10. Demir, S. and Husem, M. (2015), "Investigation of bond-slip modeling methods used in FE analysis of RC members", Struct. Eng. Mech., 56(2), 275-291. https://doi.org/10.12989/sem.2015.56.2.275
  11. EC2 (1993), Eurocode 2: Design of Concrete Structures. ENV 1992-1-2: General Rules - Structural Fire Design. European Committee for Standardization, Brussels, Belgium.
  12. Grabois, T.M., Cordeiro, G.C. and Filho, R.D.T. (2016), "Fresh and hardened-state properties of self-compacting lightweight concrete reinforced with steel fibers", Constr. Build. Mater., 104, 284-292. https://doi.org/10.1016/j.conbuildmat.2015.12.060
  13. Husem, M. (2003), "The effects of bond strengths between lightweight and ordinary aggregate-mortar, aggregate-cement paste on the mechanical properties of concrete", Mater. Sci. Eng. A, 363(1), 152-158. https://doi.org/10.1016/S0921-5093(03)00595-1
  14. Kankam, C.K. (1997), "Relationship of bond stress, steel stress and slip in reinforced concrete", J. Struct. Eng., 123(1), 79-85. https://doi.org/10.1061/(ASCE)0733-9445(1997)123:1(79)
  15. Mo, K.H., Alengaram, U.J., Visintin, P., Goh, S.H. and Jumaat, M.Z. (2015), "Influence of lightweight aggregate on the bond properties of concrete with various strength grades", Constr. Build. Mater., 84, 377-386. https://doi.org/10.1016/j.conbuildmat.2015.03.040
  16. Mo, K.H., Alengaram, U.J. and Jumaat, M.Z. (2016), "Bond properties of lightweight concrete-A review", Constr. Build. Mater., 112, 478-496. https://doi.org/10.1016/j.conbuildmat.2016.02.125
  17. Somayaji, S. (2001), Civil engineering materials, 3rd ed. New Jersey: Prentice Hall.
  18. Tang, C.W., Yen, T. and Chen, H.J. (2009), "Shear behavior of reinforced concrete beams made with sedimentary lightweight aggregate without shear reinforcement", J. Mater. Civ. Eng., ASCE, 21(12), 730-739. https://doi.org/10.1061/(ASCE)0899-1561(2009)21:12(730)
  19. Tang, C.W. (2015), "Local bond stress-slip behavior of reinforcing bars embedded in lightweight aggregate concrete", Comput. Concrete, 16(3), 449-466. https://doi.org/10.12989/cac.2015.16.3.449
  20. Zant, Z.P. and Byung, H.O. (1984), "Deformation of progressively cracking reinforced concrete beams", ACI J., 3(8), 1268-1278.
  21. Zhao, Y., Lin, H., Wu, K. and Jin, W. (2013), "Bond behaviour of normal/recycled concrete and corroded steel bars", Constr. Build. Mater., 48, 348-359. https://doi.org/10.1016/j.conbuildmat.2013.06.091

피인용 문헌

  1. Feasibility Study on Manufacturing Lightweight Aggregates from Water Purification Sludge vol.307, pp.None, 2018, https://doi.org/10.1088/1757-899x/307/1/012019