DOI QR코드

DOI QR Code

Manual model updating of highway bridges under operational condition

  • Altunisik, Ahmet C. (Department of Civil Engineering, Karadeniz Technical University) ;
  • Bayraktar, Alemdar (Department of Civil Engineering, Karadeniz Technical University)
  • 투고 : 2015.07.13
  • 심사 : 2016.11.07
  • 발행 : 2017.01.25

초록

Finite element model updating is very effective procedure to determine the uncertainty parameters in structural model and minimize the differences between experimentally and numerically identified dynamic characteristics. This procedure can be practiced with manual and automatic model updating procedures. The manual model updating involves manual changes of geometry and analyses parameters by trial and error, guided by engineering judgement. Besides, the automated updating is performed by constructing a series of loops based on optimization procedures. This paper addresses the ambient vibration based finite element model updating of long span reinforced concrete highway bridges using manual model updating procedure. Birecik Highway Bridge located on the $81^{st}km$ of Şanliurfa-Gaziantep state highway over Firat River in Turkey is selected as a case study. The structural carrier system of the bridge consists of two main parts: Arch and Beam Compartments. In this part of the paper, the arch compartment is investigated. Three dimensional finite element model of the arch compartment of the bridge is constructed using SAP2000 software to determine the dynamic characteristics, numerically. Operational Modal Analysis method is used to extract dynamic characteristics using Enhanced Frequency Domain Decomposition method. Numerically and experimentally identified dynamic characteristics are compared with each other and finite element model of the arch compartment of the bridge is updated manually by changing some uncertain parameters such as section properties, damages, boundary conditions and material properties to reduce the difference between the results. It is demonstrated that the ambient vibration measurements are enough to identify the most significant modes of long span highway bridges. Maximum differences between the natural frequencies are reduced averagely from %49.1 to %0.6 by model updating. Also, a good harmony is found between mode shapes after finite element model updating.

키워드

과제정보

연구 과제 주관 기관 : TUBITAK, Karadeniz Technical University (KTU)

참고문헌

  1. Altunisik, A.C., Bayraktar, A., Sevim, B. and Ates, S. (2011), "Ambient vibration based seismic evaluation of isolated Gulburnu highway bridge", Soil Dyn. Earthq. Eng., 31(11), 1496-1510. https://doi.org/10.1016/j.soildyn.2011.05.020
  2. Bayraktar, A., Altunisik, A.C., Sevim, B., Turker, T., Domanic, A. and Tas, Y. (2009), "Vibration characteristics of komurhan highway bridge constructed with balanced cantilever method", J. Perform. Constr. Fac., 23(2), 90-99. https://doi.org/10.1061/(ASCE)0887-3828(2009)23:2(90)
  3. Bendat, J.S. and Piersol, A.G. (2004), "Random data: Analysis and measurement procedures", John Wiley and Sons Inc., New Jersey, USA.
  4. Brownjohn, J.M.W., Magalhaes, F., Caetano, E. and Cunha, A. (2010), "Ambient vibration re-testing and operational modal analysis of the Humber Bridge", Eng. Struct., 32(8), 2003-2018. https://doi.org/10.1016/j.engstruct.2010.02.034
  5. Dubbs, N.C. and Moon, F.L. (2016), "Assessment of long-span bridge performance issues through an iterative approach to ambient vibration-based structural identification", J. Perform. Constr. Fac., 30(5), 29-42.
  6. Felber, A.J. (1993), "Development of Hybrid Bridge Evaluation System", PhD Thesis, University of British Columbia, Vancouver. (metinde atif verilmemis)
  7. Gentile, C. (2006), "Modal and structural identification of a RC arch bridge", Struct. Eng. Mech., 22(1), 53-70. https://doi.org/10.12989/sem.2006.22.1.053
  8. Jacobsen, N.J., Andersen, P. and Brincker, R. (2006), "Using enhanced frequency domain decomposition as a robust technique to harmonic excitation in operational modal analysis", Proceedings of the ISMA2006: International Conference on Noise & Vibration Engineering, Leuven, Belgium, September.
  9. Lauzon, R.G. and DeWolf, J.T. (2006), "Ambient vibration monitoring of a highway bridge undergoing a destructive test", J. Bridge Eng.-ASCE, 11(5), 602-610. https://doi.org/10.1061/(ASCE)1084-0702(2006)11:5(602)
  10. Magalhaes, F., Caetano, E., Cunha, A., Flamand, O. and Grillaud, G. (2012), "Ambient and free vibration tests of the Millau Viaduct: Evaluation of alternative processing strategies", Eng. Struct., 45, 372-384. https://doi.org/10.1016/j.engstruct.2012.06.038
  11. Magalhaes, F. and Cunha, A. (2011), "Explaining operational modal analysis with data from an arch bridge", Mech. Syst. Signal Pr., 25(5), 1431-1450. https://doi.org/10.1016/j.ymssp.2010.08.001
  12. OMA (2006), Operational Modal Analysis, Release 4.0, Structural Vibration Solution A/S, Aalborg, Denmark.
  13. Peeters, B. (2000), "System Identification and Damage Detection in Civil Engineering", PhD Thesis, K.U, Leuven, Heverlee.
  14. Polanco, N.R., May, G. and Hernandez, E.M. (2016), "Finite element model updating of semi-composite bridge decks using operational acceleration measurements", Eng. Struct., 126, 264-277. https://doi.org/10.1016/j.engstruct.2016.07.057
  15. PULSE (2006), Labshop, Version 11.2.2., Bruel & Kjaer Sound and Vibration Measurement A/S. Naerum, Denmark.
  16. Rainieri, C., Fabbrocino, G., Cosenza, E. and Manfredi, G. (2007), "Implementation of OMA procedures using labview: theory and application", Proceedings of the 2nd International Operational Modal Analysis Conference, Copenhagen, Denmark, 30 April-2 May.
  17. Real, J.I., Sanchez,, M.E., Real, T., Sanchez, F.J. and Zamorano, C. (2012), "Experimental modal analysis of railway concrete sleepers with cracks", Struct. Eng. Mech., 44(1), 51-60. https://doi.org/10.12989/sem.2012.44.1.051
  18. Ren, W.X., Zhao, T. and Harik, I.E. (2004), "Experimental and analytical modal analysis of steel arch bridge", J. Struct. Eng.-ASCE, 130(7), 1022-1031. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:7(1022)
  19. SAP2000 (2015), Computers and Structures Inc. Berkeley, California, USA.
  20. Ubertini, F., Gentile, C. and Materazzi, A.L. (2013), "Automated modal identification in operational conditions and its application to bridges", Eng. Struct., 46, 264-278. https://doi.org/10.1016/j.engstruct.2012.07.031
  21. Whelan, M.J., Gangone, M.V., Janoyan, K.D. and Jha, R. (2009), "Real-time wireless vibration monitoring for operational modal analysis of an integral abutment highway bridge", Eng. Struct., 31(10), 2224-2235. https://doi.org/10.1016/j.engstruct.2009.03.022
  22. Yang, J.R., Bail, Y., Su, H.X. and Lai, Z.C. (2012), "Full-scale dynamic testing of Qingshui River Bridge", Proceedings of the 2nd International Conference on Civil Engineering, Architecture and Building Materials, Yantai, China, May.
  23. Zhu, Q., Xu, Y.L. and Xiao, X. (2015), "Multiscale modeling and model updating of a cable-stayed bridge. I: Modeling and influence line analysis", J. Bridge Eng.-ASCE, 20(10), 112-122.

피인용 문헌

  1. Updating Finite Element Model Using Stochastic Subspace Identification Method and Bees Optimization Algorithm vol.15, pp.2, 2018, https://doi.org/10.1590/1679-78254189