Smart Structures and Systems

  • 제19권1호
  • /
  • Pages.1-10
  • /
  • 2017
  • /
  • 1738-1584(pISSN)
  • /
  • 1738-1991(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Autonomous evaluation of ambient vibration of underground spaces induced by adjacent subway trains using high-sensitivity wireless smart sensors

  • Sun, Ke (School of Earth Sciences and Engineering, Nanjing University) ;
  • Zhang, Wei (School of Earth Sciences and Engineering, Nanjing University) ;
  • Ding, Huaping (School of Electronic Science and Engineering, Nanjing University) ;
  • Kim, Robin E. (Center for Integrated Smart Sensors, KAIST) ;
  • Spencer, Billie F. Jr. (Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign)
  • 투고 : 2016.04.05
  • 심사 : 2016.10.07
  • 발행 : 2017.01.25
⟨ 이전 논문 다음 논문 ⟩

초록

The operation of subway trains induces secondary structure-borne vibrations in the nearby underground spaces. The vibration, along with the associated noise, can cause annoyance and adverse physical, physiological, and psychological effects on humans in dense urban environments. Traditional tethered instruments restrict the rapid measurement and assessment on such vibration effect. This paper presents a novel approach for Wireless Smart Sensor (WSS)-based autonomous evaluation system for the subway train-induced vibrations. The system was implemented on a MEMSIC's Imote2 platform, using a SHM-H high-sensitivity accelerometer board stacked on top. A new embedded application VibrationLevelCalculation, which determines the International Organization for Standardization defined weighted acceleration level, was added into the Illinois Structural Health Monitoring Project Service Toolsuite. The system was verified in a large underground space, where a nearby subway station is a good source of ground excitation caused by the running subway trains. Using an on-board processor, each sensor calculated the distribution of vibration levels within the testing zone, and sent the distribution of vibration level by radio to display it on the central server. Also, the raw time-histories and frequency spectrum were retrieved from the WSS leaf nodes. Subsequently, spectral vibration levels in the one-third octave band, characterizing the vibrating influence of different frequency components on human bodies, was also calculated from each sensor node. Experimental validation demonstrates that the proposed system is efficient for autonomously evaluating the subway train-induced ambient vibration of underground spaces, and the system holds the potential of greatly reducing the laboring of dynamic field testing.

키워드

과제정보

연구 과제 주관 기관 : National Science Foundation of China

참고문헌

  1. Balendra, T., Koh, C.G. and Ho, Y.C. (1991), "Dynamic response of buildings due to trains in underground tunnels", Earthq. Eng. Struct. D., 20(3), 275-291. https://doi.org/10.1002/eqe.4290200306
  2. Bennett, P.J., Soga, K., Wassell, I., Fidler, P., Abe, K., Kobayashi, Y., and Vanicek, M. (2010), "Wireless sensor networks for underground railway applications: case studies in Prague and London", Smart Struct. Syst., 6(5-6), 619-639. https://doi.org/10.12989/sss.2010.6.5_6.619
  3. Chua, K.H., Balendra, T. and Lo, K.W. (1992), "Groundborne vibrations due to trains in tunnels", Earthq. Eng. Struct. D., 21(5), 445-460. https://doi.org/10.1002/eqe.4290210505
  4. Chua, K.H., Lo, K.W. and Balendra, T. (1995), "Building response due to subway train traffic", J. Geotech. Eng., 121(11), 747-754. https://doi.org/10.1061/(ASCE)0733-9410(1995)121:11(747)
  5. Clouteau, D., Cottereau, R. and Lombaert, G. (2013), "Dynamics of structures coupled with elastic media-a review of numerical models and methods", J. Sound Vib., 332(10), 2415-2436. https://doi.org/10.1016/j.jsv.2012.10.011
  6. Degrande, G., Clouteau, D., Othman, R., Arnst, M., Chebli, H., Klein, R. and Janssens, B. (2006), "A numerical model for ground-borne vibrations from underground railway traffic based on a periodic finite element-boundary element formulation", J. Sound Vib., 293(3), 645-666. https://doi.org/10.1016/j.jsv.2005.12.023
  7. Degrande, G., Schevenels, M., Chatterjee, P., Van de Velde, W., Holscher, P., Hopman, V. and Dadkah, N. (2006), "Vibrations due to a test train at variable speeds in a deep bored tunnel embedded in London clay", J. Sound Vib., 293(3), 626-644. https://doi.org/10.1016/j.jsv.2005.08.039
  8. Gupta, S., Degrande, G. and Lombaert, G. (2009), "Experimental validation of a numerical model for subway induced vibrations", J. Sound Vib., 321(3), 786-812. https://doi.org/10.1016/j.jsv.2008.10.014
  9. Gupta, S., Liu, W.F., Degrande, G., Lombaert, G. and Liu, W.N. (2008), "Prediction of vibrations induced by underground railway traffic in Beijing", J. Sound Vib., 310(3), 608-630. https://doi.org/10.1016/j.jsv.2007.07.016
  10. ISO 5348. (1998), "Mechanical vibration and shock-Mechanical mounting of accelerometers", ISO Standard.
  11. ISO2631, S. I. (2003), "Mechanical vibration and shockevaluation of human exposure to whole body vibration Part 2: Continuous and shock induced vibration in buildings (1-80 Hz)", ISO Standard.
  12. ISO2631, S.I. (1997), "Mechanical vibration and shock: Evaluation of human exposure to whole-body vibration. Part 1: General requirements", ISO Standard.
  13. Jang, S., Jo, H., Cho, S., Mechitov, K., Rice, J.A., Sim, S.H. and Agha, G. (2010), "Structural health monitoring of a cablestayed bridge using smart sensor technology: deployment and evaluation", Smart Struct. Syst., 6(5-6), 439-459. https://doi.org/10.12989/sss.2010.6.5_6.439
  14. JGJ/G170 (2009), "Standard for limit and measuring method of building vibration and secondary noise caused by urban rail transit", Industry Standard of People's Republic of China.
  15. Jo, H., Sim, S.H., Nagayama, T. and Spencer Jr, B.F. (2011), "Development and application of high-sensitivity wireless smart sensors for decentralized stochastic modal identification", J. Eng. Mech.-ASCE, 138(6), 683-694.
  16. Kahn, J.M., Katz, R.H. and Pister, K.S. (1999), "Next century challenges: mobile networking for ‗Smart Dust'", Proceedings of the 5th annual ACM/IEEE international conference on Mobile computing and networking, ACM.
  17. Kim, J., Swartz, A., Lynch, J.P., Lee, J.J. and Lee, C.G. (2010), "Rapid-to-deploy reconfigurable wireless structural monitoring systems using extended-range wireless sensors", Smart Struct. Syst., 6(5-6), 505-524. https://doi.org/10.12989/sss.2010.6.5_6.505
  18. Kurata, N., Spencer, B.F. and Ruiz-Sandoval, M. (2005), "Risk monitoring of buildings with wireless sensor networks", Struct. Control Health, 12(3-4), 315-327. https://doi.org/10.1002/stc.73
  19. Kurzweil, L.G. (1979), "Ground-borne noise and vibration from underground rail systems", J. Sound Vib., 66(3), 363-370. https://doi.org/10.1016/0022-460X(79)90853-8
  20. LAN/MAN Standards Committee (2003), "Part 15.4: wireless medium access control (MAC) and physical layer (PHY) specifications for low-rate wireless personal area networks (LRWPANs)", IEEE Computer Society.
  21. Lee, P.J. and Griffin, M.J. (2013), "Combined effect of noise and vibration produced by high-speed trains on annoyance in buildings", J. Acoust. Soc. Am., 133(4), 2126-2135. https://doi.org/10.1121/1.4793271
  22. Li, H., Li, X., Parriaux, A. and Thalmann, P. (2013), "An integrated planning concept for the emerging underground urbanism: Deep City Method Part 2 case study for resource supply and project valuation", Tunn. Undergr. Sp. Tech., 38, 569-580. https://doi.org/10.1016/j.tust.2013.04.009
  23. Lynch, J.P., Law, K.H., Kiremidjian, A.S., Kenny, T.W., Carryer, E., and Partridge, A. (2001), "The design of a wireless sensing unit for structural health monitoring", Proceedings of the 3rd International Workshop on Structural Health Monitoring.
  24. Lynch, J.P., Sundararajan, A., Law, K.H., Kiremidjian, A.S., Carryer, E., Sohn, H. and Farrar, C.R. (2003), "Field validation of a wireless structural monitoring system on the Alamosa Canyon Bridge", Smart Struct. Mater., 5057, 267-278.
  25. International Society for Optics and Photonics. Pakzad, S.N., Fenves, G.L., Kim, S. and Culler, D.E. (2008), "Design and implementation of scalable wireless sensor network for structural monitoring", J. Inf. Syst., 14(1), 89-101. https://doi.org/10.1061/(ASCE)1076-0342(2008)14:1(89)
  26. Pitilakis, K., Tsinidis, G., Leanza, A. and Maugeri, M. (2014), "Seismic behaviour of circular tunnels accounting for above ground structures interaction effects", Soil Dyn. Earthq. Eng., 67, 1-15. https://doi.org/10.1016/j.soildyn.2014.08.009
  27. Qin, F., Zhang, X. and Zhou, Q. (2014), "Evaluating the impact of organizational patterns on the efficiency of urban rail transit systems in China", J. Transport Geog., 40, 89-99. https://doi.org/10.1016/j.jtrangeo.2014.08.002
  28. Rice, J.A. and Spencer Jr, B.F. (2009), Flexible smart sensor framework for autonomous full-scale structural health monitoring, Newmark Structural Engineering Laboratory. University of Illinois at Urbana-Champaign.
  29. Ruiz-Sandoval, M., Nagayama, T. and Spencer Jr, B.F. (2006), "Sensor development using Berkeley Mote platform", J. Earthq. Eng., 10(2), 289-309. https://doi.org/10.1080/13632460609350597
  30. Sanayei, M., Maurya, P. and Moore, J.A. (2013), "Measurement of building foundation and ground-borne vibrations due to surface trains and subways", Eng. Struct., 53, 102-111. https://doi.org/10.1016/j.engstruct.2013.03.038
  31. Sim, S.H., Li, J., Jo, H., Park, J.W., Cho, S., Spencer Jr, B.F. and Jung, H.J. (2014), "A wireless smart sensor network for automated monitoring of cable tension", Smart Mater. Struct., 23(2), 025006. https://doi.org/10.1088/0964-1726/23/2/025006
  32. Sugiyama, T., Maeda, K. and Kaneko, M. (1990), "Traveling wave effects on a tall and narrow building: observation and analysis", Comput. Geotech., 9(4), 307-324. https://doi.org/10.1016/0266-352X(90)90044-V
  33. Walker, J.G. and Chan, M.F.K. (1996), "Human response to structurally radiated noise due to underground railway operations", J. Sound Vib., 193(1), 49-63. https://doi.org/10.1006/jsvi.1996.0245
  34. Widrow, B. (1956), "A study of rough amplitude quantization by means of Nyquist sampling theory", Circuit Theory, IRE Transactions on Circuit Theory, 3(4), 266-276. https://doi.org/10.1109/TCT.1956.1086334
  35. Yang, Y.B. and Hsu, L.C. (2006), "A review of researches on ground-borne vibrations due to moving trains via underground tunnels", Adv. Struct. Eng., 9(3), 377-392. https://doi.org/10.1260/136943306777641887
  36. Yick, J., Mukherjee, B. and Ghosal, D. (2008), "Wireless sensor network survey", Comput. Netw., 52(12), 2292-2330. https://doi.org/10.1016/j.comnet.2008.04.002
  37. Zhai W.M. (2015), Vehicle-track coupled dynamics (volume 1), Science Press, Beijing, China.
  38. Zhou, G.D. and Yi, T.H. (2013), "Recent developments on wireless sensor networks technology for bridge health monitoring", Math. Probl. Eng., 2013(3), 1-33.

피인용 문헌

  1. Design of a Semi-Oval Shaped Ultrasonic Motor vol.7, pp.5, 2013, https://doi.org/10.20965/ijat.2013.p0537
  2. Numerical Simulation and In-Situ Measurement of Ground-Borne Vibration Due to Subway System vol.10, pp.7, 2018, https://doi.org/10.3390/su10072439
  3. Dynamic Responses of Soils around a One-Hole Double-Track Tunnel with the Metro Train Meeting vol.2020, pp.None, 2017, https://doi.org/10.1155/2020/1782803
  4. Modelling Ambient Vibration Responses Induced by Operation of Metro Train on Curved Rail Segment with Small Curvature Radius vol.2020, pp.None, 2017, https://doi.org/10.1155/2020/1584624
  5. Classification of Variable Foundation Properties Based on Vehicle–Pavement–Foundation Interaction Dynamics vol.20, pp.21, 2017, https://doi.org/10.3390/s20216263
  6. Aerobics Exercise Posture Tracking and Recognition System Based on Wireless Smart Sensors vol.2021, pp.None, 2017, https://doi.org/10.1155/2021/7694835