DOI QR코드

DOI QR Code

The Influence of CNTs and Lamination Structure on the Intralaminar Fracture of CFRP/GFRP Composites

CFRP/GFRP 복합재료의 층내 파괴에 대한 CNT 및 적층구조의 영향

  • Kim, Seong Hun (Department of Safety Engineering, Pukyong National University) ;
  • Yun, Yu Seong (Department of Safety Engineering, Pukyong National University) ;
  • Kang, Ji Woong (Faculty of Health Science, Daegu Haany University) ;
  • Kwon, Oh Heon (Department of Safety Engineering, Pukyong National University)
  • 김성훈 (부경대학교 안전공학과) ;
  • 윤유성 (부경대학교 안전공학과) ;
  • 강지웅 (대구한의대학교 보건학부) ;
  • 권오헌 (부경대학교 안전공학과)
  • Received : 2017.08.16
  • Accepted : 2017.10.10
  • Published : 2017.12.31

Abstract

Recently many researches were conducted on the interlaminar fracture that is a delamination between laminates by using ASTM standardized methods. However the experiment of the intralaminar a fracture is difficulty. In this study, four types of CFRP/GFRP composites with different layer structures were compared to evaluate an intralaminar fracture toughness under the mode I. Also the CNTs were added to the layer for the examination of the fracture toughness improvement. And the characteristics of the crack propagation behaviour was observed using a microscope. The obtained results can be useful for the evaluation of the intralaminar fracture toughness of the CNT reinforced CFRP/GFRP composites.

Keywords

References

  1. Y. J. Yang, S. B. Pyeon, C. S. Cha and I. Y. Yang, "Penetration Fracture Characteristics of Orthotropic CFRP Laminates Shells according to Curvature", Journal of the Korean Society of Safety, Vol. 31, No. 6, pp. 6-11, 2016. https://doi.org/10.14346/JKOSOS.2016.31.6.6
  2. J. W. Han, "Low-velocity Impact Characterization of Laminated Composite Materials" Journal of the Korean Society of Safety, Vol. 23, No. 6, pp. 34-37, 2008.
  3. S. H. Ko, Analysis of Mechanical Properties for Laminating Method in Carbon Fiber Reinforced Plastics, Jeonju University Master's Thesis, pp. 1-11, 2014.
  4. M. Iwamoto, Q. Q. Ni, T. Fujiwara and K. Kurashiki, "Intralaminar Fracture Mechanism in Unidirectional CFRP Part I : Intralaminar Toughness and AE Characteristics", Engineering Fracture Mechanics, Vol. 64, pp. 721-745, 1999. https://doi.org/10.1016/S0013-7944(99)00096-X
  5. A. C. Garg, "Intralaminar and Interlaminar Fracture in Graphite/Epoxy Laminate", Engineering Fracture Mechanics, Vol. 23, No. 4, pp. 719-733, 1986. https://doi.org/10.1016/0013-7944(86)90118-9
  6. M. Hojo, S. Matsuda, M. Tanaka, S. Ochiai and A. Murakami, "Mode I Delamination Fatigue Properties of Interlayer-Toughened CF/Epoxy Laminates", Composite Science Technology, Vol. 66, Issue 5, pp. 22-27, 2006.
  7. M. Hojo, T. Ando, M. Tanaka, T. Adachi, S. Ochiai and Y. Endo, "Modes I and II Interlaminar Fracture Toughness and Fatigue Delamination of CF/Epoxy Laminates with Selfsame Epoxy Interleaf", International Journal of Fatigue, Vol. 28, Issue 10, pp. 16-20, 2006.
  8. L. Maillet, L. Michel, G. Rico, Fressinet M. and Y. Gourinat, "A New Test Methodology Based on Structural Resonance for Mode I Fatigue Delamination Growth in an Unidirectional Composite", Composite Structures, Vol. 97, pp. 353-362, 2013. https://doi.org/10.1016/j.compstruct.2012.10.024
  9. G. R. Irwin, ASM, Vol. 22, p.147, 1948.
  10. M. Vernon, An Investigation into the Use of Edge Delaminations for Interlaminar Fracture, Master's Thesis, Centre for Composite Materials, Imperial College of Science, Technology and Medicine, 2001.
  11. J. H. Kim, "The Physical Property of MWNT/PU Composite Films", The Korean Society of Dyers and Finishers, Vol. 22, No. 3, pp. 246-248, 2010.