DOI QR코드

DOI QR Code

Effect of fly ash and plastic waste on mechanical and durability properties of concrete

  • Paliwal, Gopal (Department of Civil Engineering, Ujjain Engineering College) ;
  • Maru, Savita (Department of Civil Engineering, Ujjain Engineering College)
  • 투고 : 2017.08.09
  • 심사 : 2017.09.21
  • 발행 : 2017.12.25

초록

The disposal of polythene waste and fly ash is causing serious threat to the environment. Aim of this study is to decrease environmental pollution by using polythene waste and fly ash in concrete. In this study, cement was partially replaced with 0%, 5%, 10%, 15% and 20% fly ash (by weight) and plastic waste was added in shredded form at 0.6% by weight of concrete. The specimens were prepared for the concrete mix of M25 grade and water to cementitious material ratio (w/c) was maintained as 0.45. Fresh concrete property like workability was examined during casting the specimens. Hardened properties were found out by carrying out the experimental work on cubes, cylinders and beams which were cast in laboratory and their behavior under test were observed at 7 & 28 days for compressive strength and at 28 days for density, flexural strength, dynamic modulus of elasticity, abrasion resistance, water permeability and impact resistance. Overall results of this study show that addition of 0.6% (by weight of the concrete) plastic waste with 10% (by weight of cement) replacement of cement by fly ash result an improvement in properties of the concrete than conventional mix.

키워드

참고문헌

  1. ACI 544 (1999), Drop Weight Test.
  2. Al-Hadithi, A.I. and Hilal, N.N. (2016), "The possibility of enhancing some properties of self-compacting concrete by adding waste plastic fibers", J. Build. Eng., 8, 20-28. https://doi.org/10.1016/j.jobe.2016.06.011
  3. ASTM C597 (2009), Standard Test Method for Pulse Velocity through Concrete.
  4. Bhogayata, A. and Arora, N.K. (2011), "Green concrete from the postconsumer plastic wastes: Indian scenario", ICTSET Proc., 437-440.
  5. Bhogayata, A., Shah, K.D., Vyas, B.A. and Arora, N.K. (2012), "Performance of concrete by using non-recyclable plastic wastes as concrete constituent", J. Eng. Res. Technol., 1(4), 1-3. https://doi.org/10.15623/ijret.2012.0101001
  6. Chandrashekar, A., Ravi Shankar, A.U. and Girish, M.J. (2012), "Fatigue behavior of steel fibre reinforced concrete with fly ash", Highw. Res. J., 9-15.
  7. Chethan, C. and Chandershekhar, A. (2015), "Experimental study on effect of addition of fly ash on the properties of plastic fibers reinforced concrete", J. Res. Appl. Sci. Eng. Technol., 21(7), 1486-1491.
  8. DIN 1048 (1991), Water Permeability Test.
  9. Fly ash for Cement Concrete: Resource for High Strength and Durability of Structures at Lower Cost, Ash Utilization Division NTPC Limited A-11.
  10. Frigione, M. (2010), "Recycling of PET bottles as fine aggregate in concrete", Waste Manage., 30(6), 1101-1106. https://doi.org/10.1016/j.wasman.2010.01.030
  11. Garg, C. and Jain, A. (2014), "Green concrete: Efficient and eco-friendly construction materials", J. Res. Eng. Technol., 2(2), 259-264.
  12. Gawande, A., Zamare, G., Renge, V.C., Tayde, S. and Bharsakale, G. (2012), "An overview on waste plastic utilization in asphalting of roads", J. Eng. Res. Stud., 3(2), 1-5.
  13. Ghernouti, Y., Rabehi, B., Safi, B. and Chaid, R. (2011), "Use of recycled plastic bags waste in the concrete", J. Sci. Publ. Mater. Meth. Technol., 480-487.
  14. Halit, Y. (2008), "The effect of silica fume and high-volume class C fly ash on mechanical properties, chloride penetration and freeze-thaw resistance of self-compacting concrete", Constr. Build. Mater. Sci. Dir., 22(4), 456-462. https://doi.org/10.1016/j.conbuildmat.2007.01.002
  15. IS 10262 (2009), Indian Standard Recommended Guidelines for Concrete Mix Design.
  16. IS 1199 (1959), Methods of Sampling and Analysis of Concrete.
  17. IS 1237 (2012), Cement Concrete Flooring Tiles-Specification.
  18. IS 2383 Part-1 (1963), Methods of Test for Aggregates for Concrete.
  19. IS 3812 Part 1 (2003), Pulverized Fuel Ash-Specification; for Use as Pozzolana in Cement, Cement Mortar and Concrete.
  20. IS 3812 Part 2 (2003), Pulverized Fuel Ash-Specification; for Use as Admixture in Cement Mortar and Concrete.
  21. IS 383 (1970), Indian Standard Specification for Coarse and Fine Aggregates from Natural Sources for Concrete.
  22. IS 456 (2000), Indian Standard, Plain and Reinforced Concrete-Code of Practice.
  23. IS 516 (1959), Methods of Tests for Strength of Concrete.
  24. IS 8112 (1989), 43 Grade Ordinary Portland Cement-Specification.
  25. Islam, G.S. and Gupta, S.D. (2016), "Evaluating plastic shrinkage and permeability of polypropylene fiber reinforced concrete", J. Sustain. Built Environ., 1-10.
  26. Ismail, Z.Z. and Al-Hashmi, E.A. (2008), "Use of waste plastic in concrete mixture as aggregate replacement", Waste Manage., 28(11), 2041-2047. https://doi.org/10.1016/j.wasman.2007.08.023
  27. Khatib, J.M. (2008), "Performance of self-compacting concrete containing fly ash", Constr. Build. Mater. Sci. Dir., 22(9), 1963-1971. https://doi.org/10.1016/j.conbuildmat.2007.07.011
  28. Jayeshkumar, P., Zala, L.B. and Umrigar, F.S. (2012), "Experimental investigations on partial replacement of cement with fly ash in design mix concrete", J. Adv. Eng. Technol., 5(3), 126-129.
  29. Kandasamy, R. and Murugesan, R. (2011), "Fibre reinforced concrete using domestic waste plastic fibers", APSN J. Eng. Appl. Sci., 6(3).
  30. Kumar, A., Srivastava, V. and Kumar, R. (2014), "Effect of waste polythene on compressive strength of concrete", J. Acad. Industr. Res., 3(3), 152.
  31. Kumar, K.B.V. and Prakash, P. (2006), "Use of waste plastic in cement concrete pavement", Adv. Mater. Res. J., 15, 1-21.
  32. Liu, F., Yan, Y., Li, L., Lan, C. and Chen, G. (2013), "Performance of recycled plastic-based concrete", J. Mater. Civil Eng., 27(2), 1-9.
  33. Berndt, M.L. (2009), "Properties of sustainable concrete containing fly ash, slag and recycled concrete aggregate", Constr. Build. Mater., 23(7), 2606-2613. https://doi.org/10.1016/j.conbuildmat.2009.02.011
  34. Malak, K.R. (2015), "Use of waste plastic in concrete mixture as aggregate replacement", J. Eng. Edu. Technol., 3(2).
  35. Marthong, C. and Sarma, D.K. (2015), "Influence of PET fiber geometry on the mechanical properties of concrete: An experimental investigation", Eur. J. Environ. Civil Eng., 20(7), 771-784.
  36. Marzouk, O.Y., Dheilly, R.M. and Queneudec, M. (2007), "Valorization of post-consumer waste plastic in cementitious concrete composites", Waste Manage., 27(2), 310-318. https://doi.org/10.1016/j.wasman.2006.03.012
  37. Moinul Islam, M. and Saiful Islam, M. (2010), "Strength behavior of mortar using fly ash as partial replacement of cement", Concrete Res. Lett., 1(3), 98-106.
  38. Mody, P. and Mihu, R. (2012), "Curses of plastic on environment", Asian J. Res. Soc. Sci. Human., 2(1), 55-60.
  39. Bouzoubaa, N. and Lachemi, M. (2001), "Self-compacting concrete incorporating high volumes of class F fly ash preliminary results", Cement Concrete Res., 31, 413-420. https://doi.org/10.1016/S0008-8846(00)00504-4
  40. Naik, T.R., Singh, S.S., Huber, C.O. and Brodersen, B.S. (1996), "Use of post-consumer waste plastics in cement-based composites", Cement Concrete Res., 26(10), 1489-1492. https://doi.org/10.1016/0008-8846(96)00135-4
  41. Nibudey, R.N., Nagarnaik, P.B., Parbat, D.K. and Pande, A.M. (2013), "Cube and cylinder compressive strengths of waste plastic fiber reinforced concrete), J. Civil Struct. Eng., 4(2), 1818-1825.
  42. Patil, P.S., Mali, J.R., Tapkire, G.V. and Kumavat, H.R. (2014), "Innovative techniques of waste plastic used in concrete mixture", J. Res. Eng. Technol., 3(9), 29-32.
  43. Patil, S.L., Kale, J.N. and Suman, S. (2012), "Fly ash concrete: A technical analysis for compressive strength", J. Adv. Eng. Res. Stud., 2(1), 128-129.
  44. Pilato, L. (2010), Phenolic Resins: A Century of Progress, New York, Springer.
  45. Prahallada, M.C. and Prakash, K.B. (2013), "Effect of addition of flyash on the properties of waste plastic fibre reinforced concrete-an experimental investigation", J. Sci. Eng. Technol., 2(2), 87-95.
  46. Prinya, C., Chai, J. and Theerawat, S. (2005), "Effect of fly ash fineness on compressive strength and pore size of blended cement paste", Cement Concrete Compos., 27(4), 425-428. https://doi.org/10.1016/j.cemconcomp.2004.07.003
  47. Rafat, S. (2011), "Properties of self-compacting concrete containing class F fly ash", Mater. Des., 32(3), 1501-1507. https://doi.org/10.1016/j.matdes.2010.08.043
  48. Raghatate Atul, M. (2012), "Use of plastic in a concrete to improve its properties", J. Adv. Eng. Res. Stud., 1(3), 109-111.
  49. Rahmani, E., Dehestani, M., Beygi, M.H.A., Allahyari, H. and Nikbin, I.M. (2013), "On the mechanical properties of concrete containing waste PET particles", Constr. Build. Mater., 47, 1302-1308. https://doi.org/10.1016/j.conbuildmat.2013.06.041
  50. Rai, B., Rushad, S.T., Kr, B. and Duggal, S.K. (2012), "Study of waste plastic mix concrete with plasticizer", ISRN Civil Eng., 1-5.
  51. Ravina, D. and Mehta, P.K. (1986), "Properties of fresh concrete containing large amounts of fly ash", Cement Concrete Res., 16(2), 227-238. https://doi.org/10.1016/0008-8846(86)90139-0
  52. Sabarinathan, A. and Suresh, S. (2016), "An investigation on fresh and hardened properties of M30 concrete with plastic fibres and m-sand", J. Res. Innovat. Eng. Technol., 2(12), 64-69.
  53. Saikia, N. and De Brito, J. (2012), "Use of plastic waste as aggregate in cement mortar and concrete preparation: A review", Constr. Build. Mater., 34, 385-401. https://doi.org/10.1016/j.conbuildmat.2012.02.066
  54. Saikia, N. and De Brito, J. (2014), "Mechanical properties and abrasion behaviour of concrete containing shredded PET bottle waste as a partial substitution of natural aggregate", Constr. Build. Mater., 52, 236-244. https://doi.org/10.1016/j.conbuildmat.2013.11.049
  55. Siddique, R., Khatib, J. and Kaur, I. (2008), "Use of recycled plastic in concrete: A review", Waste Manage., 28(10), 1835-1852. https://doi.org/10.1016/j.wasman.2007.09.011
  56. Shetty, M.S. (2013), Concrete Technology-Theory and Practical, S. Chand Publishing.
  57. Trossarelli, L. and Brunella, V. (2003), Polyethylene: Discovery and Growth, UHMWPE Meeting, 5-18.
  58. Usman, M., Javaid, A. and Panchal, S. (2015), "Feasibility of waste polythene bags in concrete", J. Eng. Trend. Technol., 23(6), 317-319. https://doi.org/10.14445/22315381/IJETT-V23P259
  59. Vidivelli, B. and Mageswari, M. (2010). "Study on fly ash concrete using sem analysis", J. Environ. Res. Develop., 5(1), 46-52.
  60. .
  61. .
  62. .
  63. .
  64. .

피인용 문헌

  1. Comparison of the effect of lithium bentonite and sodium bentonite on the engineering properties of bentonite-cement-sodium silicate grout vol.9, pp.3, 2020, https://doi.org/10.12989/acc.2020.9.3.279
  2. Investigation of steel fiber effects on concrete abrasion resistance vol.9, pp.4, 2017, https://doi.org/10.12989/acc.2020.9.4.367