DOI QR코드

DOI QR Code

Pressure distribution on rectangular buildings with changes in aspect ratio and wind direction

  • Lee, Young Tae (School of Mechanical Engineering, Pusan National University) ;
  • Boo, Soo Ii (School of Mechanical Engineering, Pusan National University) ;
  • Lim, Hee Chang (School of Mechanical Engineering, Pusan National University) ;
  • Misutani, Kunio (Department of Architecture, Tokyo Polytechnic University)
  • Received : 2014.05.21
  • Accepted : 2016.09.20
  • Published : 2016.11.25

Abstract

This study aims to enhance the understanding of the surface pressure distribution around rectangular bodies, by considering aspects such as the suction pressure at the leading edge on the top and side faces when the body aspect ratio and wind direction are changed. We carried out wind tunnel measurements and numerical simulations of flow around a series of rectangular bodies (a cube and two rectangular bodies) that were placed in a deep turbulent boundary layer. Based on a modern numerical platform, the Navier-Stokes equations with the typical two-equation model (i.e., the standard $k-{\varepsilon}$ model) were solved, and the results were compared with the wind tunnel measurement data. Regarding the turbulence model, the results of the $k-{\varepsilon}$ model are in overall agreement with the experimental results, including the existing data. However, because of the blockage effects in the computational domain, the pressure recovery region is underpredicted compared to the experimental data. In addition, the $k-{\varepsilon}$ model sometimes will fail to capture the exact flow features. The primary emphasis in this study is on the flow characteristics around rectangular bodies with various aspect ratios and approaching wind directions. The aspect ratio and wind direction influence the type of wake that is generated and ultimately the structural loading and pressure, and in particular, the structural excitation. The results show that the surface pressure variation is highly dependent upon the approaching wind direction, especially on the top and side faces of the cube. In addition, the transverse width has a substantial effect on the variations in surface pressure around the bodies, while the longitudinal length has less influence compared to the transverse width.

Keywords

Acknowledgement

Supported by : Korea Institute of Energy Technology Evaluation and Planning (KETEP), National Research Foundation of Korea (NRF)

References

  1. Castro, I.P. and Robins, A.G. (1977), "The flow around a surface mounted cube in uniform and turbulent streams", J. Fluid Mech., 79(2), 307-335. https://doi.org/10.1017/S0022112077000172
  2. Cook, N.J. (1978), "Wind tunnel simulation of the adiabatic atmospheric boundary layer by roughness, barrier and mixing device methods", J. Wind Eng. Ind. Aerod., 3(2-3), 157-176. https://doi.org/10.1016/0167-6105(78)90007-7
  3. ESDU (1985), "Characteristics of atmospheric turbulence near the ground. part ii: single point data for strong winds (neutral atmosphere)", In Engineering Sciences Data Unit.
  4. Hunt, J.C.R. and Fernholz, H. (1975), "Wind-tunnel simulation of the atmospheric boundary layer: a report on Euromech 50", J Fluid Mech., 70(3), 543-559. https://doi.org/10.1017/S0022112075002182
  5. Jochen, F. and Dominic, V.T. (2008), "Hybrid LES/RANS methods for the simulation of turbulent flows", Prog. Aerosp. Sci., 44(5), 349-377. https://doi.org/10.1016/j.paerosci.2008.05.001
  6. Lim, H.C. (2007), "Generation of a turbulent boundary layer using LES", Trans of the KSME (B), 31(8), 680-687.
  7. Lim, H.C. (2009), "Wind flow around rectangular obstacles with aspect ratio", Wind Struct., 12(4), 299-312. https://doi.org/10.12989/was.2009.12.4.299
  8. Lim, H.C., Castro, I.P. and Hoxey, R.P. (2007), "Bluff bodies in deep turbulent boundary layers:Reynolds-number issues", J. Fluid Mech., 571, 97-118. https://doi.org/10.1017/S0022112006003223
  9. Lim, H.C., Thomas, T.G. and Castro, I.P. (2009), "Flow around a cube in a turbulent boundary layer: LES and experiment", J. Wind Eng. Ind. Aerod., 97(2), 96-109. https://doi.org/10.1016/j.jweia.2009.01.001
  10. Lund, T.S., Xiaohua, W. and Squires, K.D. (1998), "Generation of turbulent inflow data for Spatially-Developing boundary layer simulations", J. Comput. Phys., 140(2), 233-258. https://doi.org/10.1006/jcph.1998.5882
  11. Martinuzzi, R. and Tropea, C. (1993), "The flow around surface-mounted, prismatic obstacles placed in a fully developed channel flow", J. Fluid Eng. - ASME, 115(1), 85-92. https://doi.org/10.1115/1.2910118
  12. Meroney, R.N., Leitl, B.M., Rafailidis, S. and Schatzmann, M. (1999), "Wind tunnel and numerical modeling of flow and dispersion about several building shapes", J. Wind Eng. Ind. Aerod., 81(1-3), 333-345. https://doi.org/10.1016/S0167-6105(99)00028-8
  13. Murakami, S. (1993), "Comparison of various turbulence models applied to a bluff body", J. Wind Eng. Ind. Aerod., 46-47, 21-36. https://doi.org/10.1016/0167-6105(93)90112-2
  14. Murakami, S. and Mochida, A. (1988), "3D numerical simulation of airflow around a cubic model by means of k-E model", J. Wind Eng. Ind. Aerod., 31(2-3), 283-303. https://doi.org/10.1016/0167-6105(88)90009-8
  15. Nozawa, K. and Tamura, T. (2002), "Large eddy simulation of the flow around a low-rise building immersed in a rough-wall turbulent boundary layer", J. Wind Eng. Ind. Aerod., 90(10), 1151-1162. https://doi.org/10.1016/S0167-6105(02)00228-3
  16. Richards, P.J., Hoxey, R.P. and Short, L.J. (2001), "Wind pressure on a 6 m cube", J. Wind Eng. Ind. Aerod., 89(14-15), 1553-1564. https://doi.org/10.1016/S0167-6105(01)00139-8
  17. Richards, P.J., Hoxey, R.P., Connell, B.D. and Lander, D.P. (2007), "Wind-tunnel modelling of the Silsoe cube", J. Wind Eng. Ind. Aerod., 95(9-11), 1384-1399. https://doi.org/10.1016/j.jweia.2007.02.005
  18. Salim, S.M. and Cheah, S.C. (2009), "Wall $y^{+}$ strategy for dealing with wall-bounded turbulent flows", Proceedings of the International Multi-Conference of Engineers and Computer Scientists, Hong Kong.
  19. Schofield, W. and Logan, E. (1990), "Turbulent shear flow over surface-mounted obstacles", J. Fluid Eng. - ASME, 112(4), 376-385. https://doi.org/10.1115/1.2909414
  20. Shur, M. L., Spalart, P.R., Strelets, M.K. and Travin, A.K. (2008), "A hybrid RANS-LES approach with delayed-DES and wall-modelled LES capabilities", J. Heat Fluid Fl., 29(6), 1638-1649. https://doi.org/10.1016/j.ijheatfluidflow.2008.07.001
  21. Simiu, E. and Scanlan, R.H. (1996), Wind effects on Structures-Fundamentals and Applications to Design, (3rd Ed.). Wiley, New York, USA.
  22. Tieleman, H.W. and Akins, R.E. (1996), "The effect of incident turbulence on the surface pressures of surface-mounted prisms", J Fluid. Struct., 10(4), 367-393. https://doi.org/10.1006/jfls.1996.0024
  23. Tominaga, Y. and Stathopoulos, T. (2009), "Numerical simulation of dispersion around an isolated cubic building: comparison of various types of k-$\varepsilon$ models", Atmos. Environ., 43(20), 3200-3210. https://doi.org/10.1016/j.atmosenv.2009.03.038
  24. Xie, Z.T. and Castro, I.P. (2008), "Efficient generation of inflow conditions for large-eddy simulations of street-scale flows", Flow Turbul. Combus., 81(3), 449-470. https://doi.org/10.1007/s10494-008-9151-5

Cited by

  1. Wind effect on grooved and scallop domes vol.148, 2017, https://doi.org/10.1016/j.engstruct.2017.07.003
  2. The effect of incidence angle on the mean wake of surface-mounted finite-height square prisms vol.66, 2017, https://doi.org/10.1016/j.ijheatfluidflow.2017.05.012
  3. Post-Disaster Survey and Analysis of Glass Curtain Wall under Influence of Super Typhoon “Meranti” vol.455, pp.None, 2020, https://doi.org/10.1088/1755-1315/455/1/012044
  4. Wind loading of a finite prism: aspect ratio, incidence and boundary layer thickness effects vol.31, pp.3, 2016, https://doi.org/10.12989/was.2020.31.3.255
  5. A design method for multi-degree-of-freedom aeroelastic model of super tall buildings vol.32, pp.3, 2016, https://doi.org/10.12989/was.2021.32.3.219
  6. A design method for multi-degree-of-freedom aeroelastic model of super tall buildings vol.32, pp.3, 2016, https://doi.org/10.12989/was.2021.32.3.219
  7. Interference effect on corner-configured structures with variable geometry and blockage configurations under wind loads using CFD vol.22, pp.8, 2016, https://doi.org/10.1007/s42107-021-00400-0
  8. A fabrication method of continuous aero-model for high chimney vol.34, pp.None, 2016, https://doi.org/10.1016/j.istruc.2021.09.098
  9. A fabrication method of continuous aero-model for high chimney vol.34, pp.None, 2016, https://doi.org/10.1016/j.istruc.2021.09.098