Coupled systems mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Comparison of an ultrasonic distance sensing system and a wire draw distance encoder in motion monitoring of coupled structures

  • Kuanga, K.S.C. (Department of Civil and Environmental Engineering, National University of Singapore) ;
  • Hou, Xiaoyan (Department of Civil and Environmental Engineering, National University of Singapore)
  • Received : 2015.05.26
  • Accepted : 2016.08.19
  • Published : 2016.06.25
⟨ Previous Next ⟩

Abstract

Coupled structures are widely seen in civil and mechanical engineering. In coupled structures, monitoring the translational motion of its key components is of great importance. For instance, some coupled arms are equipped with a hydraulic piston to provide the stiffness along the piston axial direction. The piston moves back and forth and a distance sensing system is necessary to make sure that the piston is within its stroke limit. The measured motion data also give us insight into how the coupled structure works and provides information for the design optimization. This paper develops two distance sensing systems for coupled structures. The first system measures distance with ultrasonic sensor. It consists of an ultrasonic sensing module, an Arduino interface board and a control computer. The system is then further upgraded to a three-sensor version, which can measure three different sets of distance data at the same time. The three modules are synchronized by the Arduino interface board as well as the self-developed software. Each ultrasonic sensor transmits high frequency ultrasonic waves from its transmitting unit and evaluates the echo received back by the receiving unit. From the measured time interval between sending the signal and receiving the echo, the distance to an object is determined. The second distance sensing system consists of a wire draw encoder, a data collection board and the control computer. Wire draw encoder is an electromechanical device to monitor linear motion by converting a central shaft rotation into electronic pulses of the encoder. Encoder can measure displacement, velocity and acceleration simultaneously and send the measured data to the control computer via the data acquisition board. From experimental results, it is concluded that both the ultrasonic and the wire draw encoder systems can obtain the linear motion of structures in real-time.

Keywords

Acknowledgement

Supported by : National Research Foundation

References

  1. Brownjohn, J.M., De Stefano, A., Xu, Y.L., Wenzel, H. and Aktan, A.E. (2011), "Vibration-based monitoring of civil infrastructure: challenges and successes", J. Civil Struct. Health Monitor., 1(3-4), 79-95. https://doi.org/10.1007/s13349-011-0009-5
  2. Carullo, A., Ferraris, F., Graziani, S., Grimaldi, U. and Parvis, M. (1996), "Ultrasonic distance sensor improvement using a two-level neural-network", Proceedings of the IEEE Transactions on Instrumentation and Measurement, 45(2), 677-682. https://doi.org/10.1109/19.492808
  3. Frangopol, D. M. and Soliman, M. (2016), "Life-cycle of structural systems: Recent achievements and future directions", Struct. Infrastruct. Eng., 12(1), 1-20. https://doi.org/10.1080/15732479.2014.999794
  4. Gasparesc, G. and Gontean, A. (2014), "Performance evaluation of ultrasonic sensors accuracy in distance measurement", Proceedings of the 11th International Symposium on (pp. 1-4).
  5. Lee, K.M., Choi, J. and Bang, Y.B. (2016), "Shaft position measurement using dual absolute encoders", Sensors .Actuators A: Phys., 238, 276-281. https://doi.org/10.1016/j.sna.2015.12.027
  6. Marioli, D., Sardini, E. and Taroni, A. (1988), "Ultrasonic distance measurement for linear and angular position control", Proceedings of the IEEE transactions on instrumentation and measurement, 37(4), 578-581. https://doi.org/10.1109/19.9817
  7. Minomi, S., Yamamoto, H., Nakamura, K. and Yamazaki, K. (2012), "A study of pedestrian observation system with ultrasonic distance sensor", Proceedings of the 14th International Conference on, 251-256.
  8. Nguyen, T.V., Mariani, S., Phillips, R.R., Kijanka, P., di Scalea, F.L. and Staszewski, W.J. (2013), "Noncontact ultrasonic guided wave inspection of rails", Proceedings of the ASME International Mechanical Engineering Congress and Exposition (pp. V011T06A012-V011T06A012), American Society of Mechanical Engineers.
  9. Ogitsu, T., Ikegami, T., Kato, S. and Mizoguchi, H. (2014), "Application of draw wire encoder to vehiclefollowing device for personal vehicle", Proceedings of the IEEE International Conference on, 50-54.
  10. Ogitsu, T., Ikegami, T., Kato, S. and Mizoguchi, H. (2014), "Application of draw wire encoder to vehiclefollowing device for personal vehicle", Proceedings of the IEEE International Conference on, pp. 50-54.
  11. Zhu, X.Q. and Law, S.S. (2016), "Recent developments in inverse problems of vehicle-bridge interaction dynamics", J. Civil Struct. Health Monitor., 6(1), 107-128. https://doi.org/10.1007/s13349-016-0155-x