Journal of the Korean Wood Science and Technology

The Korean Society of Wood Science & Technology (한국목재공학회)
권호 표지
DOI QR코드

DOI QR Code

Performance Comparison of Korean Tongue and Groove Joint between Hand-made and Pre-cut

주먹장 접합부의 수가공과 기계가공의 성능비교

  • Kim, Gwang-Chul (Department of Housing Environmental Design. Chonbuk National University) ;
  • Kim, Jun-Ho (Department of Housing Environmental Design. Chonbuk National University)
  • 김광철 (전북대학교 주거환경학과) ;
  • 김준호 (전북대학교 주거환경학과)
  • Received : 2016.05.02
  • Accepted : 2016.06.19
  • Published : 2016.09.25
Download PDF
⟨ Previous Next ⟩

Abstract

Recently, the demand on the Hanok have been increased with social change. However, Hanok has a major problem of a rising costs caused by hand-made process. So, performance comparison between hand-made process and pre-cut process was conducted to modularize the joints in Hanok. Douglas-fir was used to manufacture the structural size dovetail joints by hand-made and pre-cut precess. The bending strengths on joints with two process were evaluated. The average ultimate load of pre-cut joints was 1.5 times higher than that of hand-made joints. F-test results in both process showed a great relationships between ultimate load and tenon's size variation. The length and thickness of tenon showed a proportional relationship with the ultimate load, but the tenon width showed inverse proportion with the ultimate load. This results may be used as basic data for the joint modularization of Hanok.

최근 여러 사회적인 변화에 따라 한옥에 대한 수요가 증가하고 있다. 하지만 한옥은 수가공으로 인한 가격 상승의 큰 문제점을 가지고 있다. 따라서 한옥 접합부의 모듈화를 위해 기계가공과 수가공과의 성능비교를 하였다. 더글라스퍼를 이용하여 두 가공법으로 실대재 주먹장을 제작하였다. 두 가공법에 대해 휨 성능을 평가하였다. 평균 최대하중은 같은 치수의 그룹을 비교했을 때 기계가공이 수가공에 비해 약 1.5배 더 높았다. 유의성 검증결과 두 가공법 모두 각 요소의 크기변화는 강도에 큰 영향을 미치는 것으로 나타났다. 다중회귀분석을 통해 목길이와 목두께는 최대하중과 비례 관계였으나 목너비는 반비례관계인 것을 알 수 있었다. 본 연구는 한옥 접합부를 모듈화 함에 있어 기초자료로 사용할 수 있을 것이다.

Keywords

References

  1. Kim, G.-C., Kang, C.-W., Matsumrura, J. 2009. Performance Assessment of Existing Korean School Building (I) - Mechanical And Physical Prperties of The Rafter Members -. Journal of the Faculty of Agriculture, Kyushu University 54(2): 439-444.
  2. Kim, G.-C., Kang, C.-W., Matsumrura, J. 2009. Performance Assessment of Existing Korean School Building (II) - Study on the Species Identification and Residual Strength Properties of the Rafter Members-. Journal of the Faculty of Agriculture, Kyushu University 54(2): 445-448.
  3. Kim, G.-C., Kang, C.-W., Matsumrura, J. 2009. Studies on the Evaluation of Doweal-Bearing Strength for the Manufacture of Skin Timber. Journal of the Faculty of Agriculture, Kyushu University 54(2): 449-455.
  4. Kim, G.-C., Kang, C.-W., Matsumrura, J. 2010. Estimating The Structural Capacity of Skin-timber. Journal of the Faculty of Agriculture, Kyushu University 55(2): 287-295.
  5. Kim, G.-C., Kang, C.-W., Matsumrura, J. 2011. A Study on the Bending Properties of Traditional Korean Joints. Journal of the Faculty of Agriculture, Kyushu University 56(2): 353-360.
  6. Kim, G.-C., Kim, J.-H. 2015. A Study on the Field Survey of Traditional Korean Joint's Standardization. Proceedings of The Korean Society of Wood Science and Technology annual meeting. pp.28-29.
  7. Hwang, G.-H., Park, M.-J., Park, J.-S. 2009. Tensile Performance of Pre-cut Dovetail Joint for Larch Glulam. Architectural Institute of Korea 29(1): 483-486.
  8. KS F 2150: Method of Static Bending Test for Full Sized Structural Lumber.
  9. Korean Building Code. 2005. Architectural Institute of Korea.
  10. Lee, S.-Y., Hwang, J.-K., Hong, S.-G. 2010. Failure Modes by Dovetail Angle and Mechanical Modeling in the Dovetail Joint of Traditional Wooden Structures. Architectural Institute of Korea 26(12).
  11. Song, J.-M., Park, H.-K. 2008. Structure Analysis of the Fist Connection Resistance Performance for Traditional Wooden Structural System Improvement This paper predic. Architectural Institute of Korea 24(6): 3-10.