Steel and Composite Structures

  • 제21권5호
  • /
  • Pages.1017-1029
  • /
  • 2016
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Hysteretic behaviour of circular tubular T-joints with local chord reinforcement

  • Shao, Y.B. (School of Mechatronic Engineering, Southwest Petroleum University) ;
  • Wang, Y.M. (School of Mechatronic Engineering, Southwest Petroleum University) ;
  • Yang, D.P. (Technology Inspection Center, China Petroleum & Chemical Corporation)
  • 투고 : 2016.04.14
  • 심사 : 2016.07.11
  • 발행 : 2016.08.10
⟨ 이전 논문 다음 논문 ⟩

초록

When a welded circular hollow section (CHS) tubular joint is subjected to brace axial loading, failure position is located usually at the weld toe on the chord surface due to the weak flexural stiffness of the thin-walled chord. The failure mode is local yielding or buckling in most cases for a tubular joint subjected to axial load at the brace end. Especially when a cyclic axial load is applied, fracture failure at the weld toe may occur because both high stress concentration and welding residual stress along the brace/chord intersection cause the material in this region to become brittle. To improve the ductility as well as to increase the static strength, a tubular joint can be reinforced by increasing the chord thickness locally near the brace/chord intersection. Both experimental investigation and finite element analysis have been carried out to study the hysteretic behaviour of the reinforced tubular joint. In the experimental study, the hysteretic performance of two full-scale circular tubular T-joints subjected to cyclic load in the axial direction of the brace was investigated. The two specimens include a reinforced specimen by increasing the wall thickness of the chord locally at the brace/chord intersection and a corresponding un-reinforced specimen. The hysteretic loops are obtained from the measured load-displacement curves. Based on the hysteretic curves, it is found that the reinforced specimen is more ductile than the un-reinforced one because no fracture failure is observed after experiencing similar loading cycles. The area enclosed by the hysteretic curves of the reinforced specimen is much bigger, which shows that more energy can be dissipated by the reinforced specimen to indicate the advantage of the reinforcing method in resisting seismic action. Additionally, finite element analysis is carried out to study the effect of the thickness and the length of the reinforced chord segment on the hysteretic behaviour of CHS tubular T-joints. The optimized reinforcing method is recommended for design purposes.

키워드

참고문헌

  1. Aguilera, J. and Fam, A. (2013), "Retrofitting tubular steel T-joints subjected to axial compression in chord and brace members using bonded FRP plates or through-wall steel bolts", Eng. Struct., 48, 602-610. https://doi.org/10.1016/j.engstruct.2012.09.018
  2. Ahmadi, H., Yeganeh, A., Mohammadi, A.H. and Zavvar, E. (2016), "Probabilistic analysis of stress concentration factors in tubular KT-joints reinforced with internal ring stiffeners under in-plane bending loads", Thin-Wall. Struct., 99, 58-75. https://doi.org/10.1016/j.tws.2015.11.010
  3. Chen, C., Shao, Y.B. and Yang, J. (2015), "Study on fire resistance of circular hollow section (CHS) T-joint stiffened with internal rings", Thin-Wall. Struct., 92, 104-114. https://doi.org/10.1016/j.tws.2015.02.005
  4. Chiew, S.P., Lie, S.T., Lee, C.K. and Huang, Z.W. (2004), "Fatigue performance of cracked tubular T-joints under combined loads, I: Experimental", J. Struct. Eng., ASCE, 130(4), 562-571. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:4(562)
  5. Chiew, S.P., Zhang, J.C., Shao, Y.B. and Qiu, Z.H. (2012), "Experimental and numerical analysis of complex welded tubular DKYY-joints", Adv. Struct. Eng., 15(9), 1585-1594.
  6. Choo, Y.S., Liang, J.X., van der Vegte, G.J. and Liew, J.Y.R. (2004), "Static strength of doubler plate reinforced CHS X-joints loaded by in-plane bending", J. Constr. Steel Res., 60(12), 1725-1744. https://doi.org/10.1016/j.jcsr.2004.05.004
  7. Choo, Y.S., van der Vegte, G.J., Zettlemoyer, N. and Li, B.H. (2005), "Static strength of T-joints reinforced with doubler or collar plates-part I: experimental investigations", J. Struct. Eng., ASCE, 131(1), 119-128. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:1(119)
  8. Fung, T.C., Chan, T.K. and Soh, C.K. (1999), "Ultimate capacity of doubler plate reinforced tubular joints", J. Struct. Eng., ASCE, 125(8), 891-899. https://doi.org/10.1061/(ASCE)0733-9445(1999)125:8(891)
  9. Gandhi, P., Raghava, G. and Ramachandra Murthy, D.S. (2000), "Fatigue behavior of internally ringstiffened welded steel tubular joints", J. Struct. Eng., ASCE, 126(7), 809-815. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:7(809)
  10. Gao, F., Guan, X.Q., Zhu, H.P. and Xia, Y. (2015a), "Hysteretic bahaviour of tubular T-joints reinforced with doubler plates after fire exposure", Thin-Wall. Struct., 92, 10-20. https://doi.org/10.1016/j.tws.2015.02.010
  11. Gao, F., Guan, X.Q., Zhu, H.P. and Liu, X.N. (2015b), "Fire resistance of tubular T-joints reinforced with collar plate", J. Constr. Steel Res., 115, 106-120. https://doi.org/10.1016/j.jcsr.2015.07.021
  12. Hoon, K.H., Wong, L.K. and Soh, A.K. (2001), "Experimental investigation of a doubler-plate reinforced tubular T-joint subjected to combined loadings", J. Constr. Steel Res., 57(9), 1015-1039. https://doi.org/10.1016/S0143-974X(01)00023-2
  13. Lee, M.M.K. and Llewelyn-Parry, A. (2004), "Offshore tubular T-joints reinforced with internal plain annular ring stiffeners", J. Struct. Eng., ASCE, 130(6), 942-951. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:6(942)
  14. Lee, M.M.K. and Llewelyn-Parry, A. (2005), "Strength prediction for ring-stiffened DT-joints in offshore jacket structures", Eng. Struct., 27(3), 421-430. https://doi.org/10.1016/j.engstruct.2004.11.004
  15. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2013), "Numerical investigation of FRP-strengthened tubular T-joints under axial compressive loads", Compos. Struct., 100, 71-78. https://doi.org/10.1016/j.compstruct.2012.12.020
  16. Lesani, M., Bahaari, R.M. and Shokrieh, M.M. (2014), "Experimental investigation of FRP-stengthened tubular T-joints under axial compressive loads", Constr. Build. Mater., 53, 243-252. https://doi.org/10.1016/j.conbuildmat.2013.11.097
  17. Myers, P.T., Brennan, F.P. and Dover, W.S. (2001), "The effect of rack/rib plate on the stress concentration factors in jack-up chords", Mar. Struct., 14(4-5), 485-505. https://doi.org/10.1016/S0951-8339(00)00051-4
  18. Qin, F., Fung, T.C. and Soh, C.K. (2001), "Hysteretic behavior of completely overlap tubular joints", J. Constr. Steel Res., 57(7), 811-829. https://doi.org/10.1016/S0143-974X(01)00002-5
  19. Shao, Y.B. and Lie, S.T. (2005), "Parametric equation of stress intensity factor for tubular K-joint under balanced axial loads", Int. J. Fatigue, 27(6), 666-679. https://doi.org/10.1016/j.ijfatigue.2004.11.003
  20. Shao, Y.B., Lie, S.T. and Chiew, S.P. (2010), "Static strength of tubular T-joints with reinforced chord under axial compression", Adv. Struct. Eng., 13(2), 369-377. https://doi.org/10.1260/1369-4332.13.2.369
  21. Shao, Y.B., Li, T., Lie, S.T. and Chiew, S.P. (2011a), "Hysteretic behaviour of square tubular T-joints with chord reinforcement under axial cyclic loading", J. Constr. Steel Res., 67(1), 140-149. https://doi.org/10.1016/j.jcsr.2010.08.001
  22. Shao, Y.B., Lie, S.T., Chiew, S.P. and Cai, Y.Q. (2011b), "Hysteretic performance of circular hollow section tubular joints with collar-plate reinforcement", J. Constr. Steel Res., 67(12), 1936-1947. https://doi.org/10.1016/j.jcsr.2011.06.010
  23. Soh, C.K., Fung, T.C., Qin, F. and Gho, W.M. (2001), "Behaviour of completely overlap joints under cyclic loading", J. Struct. Eng., ASCE, 127(2), 122-128. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:2(122)
  24. van der Vegte, G.J., Choo, Y.S., Liang, J.X., Zettlemoyer, N. and Liew, J.Y.R. (2005), "Static strength of Tjoints reinforced with doubler or collar plates, II: Numerical simulations", J. Struct. Eng., ASCE, 131(1), 129-139. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:1(129)
  25. Wang, W. and Chen, Y.Y. (2007), "Hysteretic behaviour of tubular joints under cyclic loading", J. Constr. Steel Res., 63(10), 1384-1395. https://doi.org/10.1016/j.jcsr.2006.12.002
  26. Yang, J., Shao, Y.B. and Chen, C. (2012), "Static strength of chord reinforced tubular Y-joints under axial loading", Mar. Structures, 29(1), 226-245. https://doi.org/10.1016/j.marstruc.2012.06.003
  27. Yin, Y., Han, Q.H., Bai, L.J., Yang, H.D. and Wang, S.P. (2009), "Experimental study on hysteretic behaviour of tubular N-joints", J. Constr. Steel Res., 65(2), 326-334. https://doi.org/10.1016/j.jcsr.2008.07.006
  28. Zhu, L., Zhao, Y., Li, S.W., Huang, Y.X. and Ban, L.R. (2014), "Numerical analysis of the axial strength of CHS T-joints reinforced with external stiffeners", Thin-Wall. Struct., 85, 481-488. https://doi.org/10.1016/j.tws.2014.09.018
  29. Zhu, L., Han, S., Song, Q.M., Ma, L.M., Wei, Y. and Li, S.W. (2016), "Experimental study of the axial compressive strength of CHS T-joints reinforced with external stiffening rings", Thin-Wall. Struct., 98(B), 245-251. https://doi.org/10.1016/j.tws.2015.09.029