Design of an 8x Four-group Inner-focus Zoom System Using a Focus Tunable Lens

Abstract

This study presents an 8x four-group inner-focus zoom lens with one-moving group for a compact camera by use of a focus tunable lens (FTL). In the initial design stage, we obtained the powers of lens groups by paraxial design based on thin lens theory, and then set up the zoom system composed of four lens modules. Instead of numerically analytic analysis for the zoom locus, we suggest simple analysis for that using lens modules optimized. After replacing four groups with equivalent thick lens modules, the power of the fourth group, which includes a focus tunable lens, is designed to be changed to fix the image plane at all positions. From this design process, we can realize an 8x four-group zoom system having one moving group by employing a focus tunable lens. The final designed zoom lens has focal lengths of 4 mm to 32 mm and apertures of F/3.5 to F/4.5 at wide and tele positions, respectively.

I. INTRODUCTION

A zoom system consists of several groups including a variator for zooming and a compensator for keeping the image plane stationary. Because the movement of a compensator is generally smaller than that of a variator, a compensator can be replaced by a liquid lens. Zoom systems having one moving group plus a liquid lens have been reported [1, 2], but the liquid lens actuated by electro-wetting is composed of a cell filled with two immiscible liquids. One is an oil-like electrical insulator, and the other is an electrolyte. Because of small refractive index difference between these materials, the magnitude of a changeable optical power obtained by this liquid lens is limited compared to that of a focus tunable lens.

Figure 1 shows the structure of the focus tunable lens (FTL) composed of a liquid and a thin elastic membrane enclosing it [3, 4]. An optical liquid is concealed in a container with at least one side being an elastic membrane. A change of pressure in the container causes the membrane to deflect, thus forming a lens. This tunable lens design has the advantage of being convertible from a convex to a concave shape. Thus, various focal lengths can be obtained by changing the curvature of a thin membrane. Since the focus tunable lens has also the big refractive index difference between the materials of air and liquid, not liquid and liquid, it can make greater changes in optical power than previous liquid lenses even for the same curvature. In addition, the focus tunable lens is known to be much more stable from the gravitational force at large aperture than the liquid lens is [4]. Because of these merits of a focus tunable lens, we can use it as a compensator in a compact zoom lens design.

FIG. 1.Structure of the focus tunable lens and variation of focal length: (a) positive and (b) negative focal lengths.

Much research on optical systems using liquid lenses has been reported. Most of them are for auto-focusing by a liquid lens [5, 6]. However, such lenses can be used to compensate for image position errors generated by changes in the power and the object distance.

Focus tunable lenses performing well as a compensator in zoom systems have also been reported [7, 8]. In 2013, Lee proposed a zoom lens using tunable lenses for a laparoscope, which has the apertures of F/4.9 to F/6.04 at two extreme positions, a three-group configuration, and a total track of 23.26 mm [8]. The tunable lens proposed by Lee is located at the first and third groups as variator and compensator, respectively. Because all groups are fixed during zooming process, the zoom ratio is limited to 4x at most.

In this research, to achieve a higher zoom ratio of 8x, we propose a four-group inner-focus zoom system having one moving group by employing a focus tunable lens. We locate the FTL at the fourth group as a compensator. Because this group is always fixed, so the curvature of an FTL should be changed to compensate for image position errors induced by focal-length changes at different zoom positions. This configuration enables the zoom lens to have a higher zoom ratio of 8x and a compact size.

 

II. ANALYSIS OF A FOUR-GROUP INNER-FOCUS ZOOM SYSTEM WITH COMPENSATOR OF FOCUS TUNABLE LENS

The layout of the four-group inner-focus zoom system, consisting of a focus tunable lens, is shown in Fig. 2. The powers of the groups are denoted by k1, k2, k3, k4w at a wide position, and k4t at a tele position. The zoom system is composed of a fixed first group, a moving second group, a fixed third group, and a fixed fourth group. Because the second group moves to the image side to have a longer focal length, the power of the fourth group should be varied to keep the image position stationary. This variable power of the fourth group can be realized by varying an FTL whose curvature is changed. Thus, the four-group inner-focus zoom system with an FTL has a structural advantage and the same total track at all zoom positions. This configuration is useful in obtaining a compact zoom system for a camera. The initial design of this zoom system with an infinite object can be formulated as follows [9, 10]:

where K is the optical power at a zoom position, and bfd is the back focal distance. Equations (1) and (2) can be rearranged as follows:

FIG. 2.Layout of the four-group inner-focus zoom system with a focus tunable lens.

Therefore, Eqs. (3) and (4) can be expressed in a matrix form for wide and tele positions as follows:

If the Gauss-Jordan elimination method is applied, Eq. (5) is replaced by

where bij is given as a function of bij (Kw, Kt, z1w, z2w, z3w, bfdw, z1t, z2t, z3t, bfdt) with Kw and Kt being the optical powers at wide and tele positions, respectively. The parameters zji(j = 1, 2, 3) and bfdi are the distances between adjacent principal planes at the ith zoom position. From Eq. (6), four equations are obtained:

Plugging the condition of Eq. (9) into Eq. (10) results in an expression for the unknown parameter k1:

where coefficients of A, B, C, D, and E are given as a function of Kw, Kt, z1w, z2w, z3w, bfdw, z1t, z2t, z3t, bfdt. Solving Eq. (11), we can get k1. As a result, k2, k3 and k4 are sequentially determined from Eqs. (7)~(9). In common with other paraxial designs, solving the above equations by hand is difficult, so we developed a program tool to calculate the powers of each group at given zooming parameters of z1, z2, z3, bfd, and K in Matlab, as shown in Fig. 3. As a result, obtaining physically-meaningful initial zoom data through a paraxial design was possible [11].

FIG. 3.Windows for calculating the powers of groups and checking the data.

 

III. PARAXIAL DESIGN OF AN 8X FOUR-GROUP INNER-FOCUS ZOOM SYSTEM

The paraxial design for a zoom system is carried out at two extreme positions. To reduce the amount of the curvature variation at the FTL, the powers of the fourth group including an FTL are set to be the same at wide and tele positions. This configuration can realize a simple and mechanically stable zoom system. For the initial design of an 8x four-group inner-focus zoom system, we input the proper distances between principal points and the targeted total powers at the wide and the tele positions. These starting values are empirically selected to satisfy the following basic requirements for an 8x compact zoom system:

By inputting these starting values for Eq. (12) into the program tool, we can immediately obtain the power of each group, as shown in Fig. 3. In that figure, the Result Data shows the four solution cases obtained from Eq. (7) to Eq. (11). These solutions for k1, k2, k3, k4 are summarized in Table 1.

TABLE 1.Focal lengths of groups at four solution cases (in mm)

The next step is to select the physically-meaningful data among solutions given in Fig. 3. This process can be carried out by executing the ray trace and the ‘Check Data’ analysis of the program developed in this study. The case 4 of Table 1 is confirmed to fulfill the requirements for the available zoom system with 8x.

 

IV. INITIAL DESIGN FOR AN 8X FOUR-GROUP ZOOM LENS

We have set up a zoom lens system with four thick-lens modules, for which the power of each lens group and the zoom loci inputs are taken from the case 4 of Table 1 and Eq. (12), respectively. The lens modules do not reflect higher-order aberrations, so reducing the aperture and the field size of the system is desirable. Thus, we took a zoom system with a half image size of 1 mm and f-numbers of F/5 at the wide position to F/7 at the tele position. The air distances between modules were constrained to be longer than 0.5 mm for the mounting space.

In order to get an initial zoom system, we optimized the lens module parameters so that the specific constraints were satisfied [12]. In Table 1 of the previous section, the thickness of each group and the air spaces are not presented. They can be derived by specifying the design variables of the lens modules, such as the front focal length (MFF) and the back focal length (MBF) of each group, and the air distances between the modules. Figure 4 shows the initial zoom design composed of four lens modules obtained from this process. The focal lengths range from 4.0 mm to 32.0 mm. Table 2 shows the design data for each module and the air distances between modules.

FIG. 4.An 8x four-group zoom system consisting of lens modules.

TABLE 2.Design data for the lens modules and air distances between modules in the lens module zoom system (in mm)

Numerically analytic approaches using extensive calculations to obtain zoom locus have been reported [1, 10, 11]. However, handling many equations given in Section 2 at the same time is very complicated and requires much more effort. First of all, handling analytically all the first-orders of an FTL at all zoom positions is hard work. In this research, therefore, we analyze the zoom loci at all positions by optimizing the lens modules.

First, we calculate the image position shifts induced by the variator’s moving at different zoom positions, as shown in Fig. 5. We then locate the focus tunable lens at the fourth lens group as a compensator. Because this group is always fixed, so the curvature of an FTL should be changed to compensate simultaneously for image position shifts induced by focal-length changes at different zoom positions.

FIG. 5.Zoom locus of an 8x four-group zoom system with no compensator.

Figure 6 shows the lens module zoom system with a fixed compensator, of which focal lengths are changed from -14.23 mm to -16.34 mm to -14.23 mm. Figure 7 illustrates the focal lengths of the fourth group at various positions.

FIG. 6.An 8x four-group lens module zoom system with a compensator having variable powers.

FIG. 7.Focal lengths of the fourth group with zoom position.

 

V. OPTIMIZED DESIGN FOR A ZOOM SYSTEM USING FOCUS TUNABLE LENS

5.1. Converting Lens Modules into Real Lens Groups Successively

In the lens module zoom system of Fig. 6, four lens modules were successively, not separately, converted into real lens groups using an automatic design method. The conversion of the lens module into a real lens group is based on the first-order properties given in Table 2 and Fig. 7.

At first, the first lens module is converted into the real lens equivalent to the module within the first-order properties, while the other three groups are lens modules and, unlike the first group, have not yet been carried through this converting process. By these iterative processes, the second group, third group, and fourth group are successively converted to real lens groups [13]. As a result, the lens module zoom system is group by group converted to the initial real lens zoom system without losing the equivalence to each other.

In the converting process of the fourth lens group, the curvature of a focus tunable lens should be changed to keep the image plane stationary at different zoom positions. From the structure of an FTL in Fig. 1, while the edge thickness (e) of an FTL is always fixed, but its central thickness is changed by shape-changing polymer membrane, as shown in Fig. 8 [4, 14]. Assuming that the back surface of the FTL is rigid and a plane in this study, the sag (S) and thickness (T) with radius (R) of curvature of a membrane are given by

FIG. 8.The shape-changing tunable lens and thickness variation by its curvature change.

The focus tunable lens as a compensator is designed to satisfy the conditions for its sag and thickness given in Eqs. (13) and (14), respectively. Its edge thickness was constrained to be more than 0.4 mm so that the curvature of the membrane can be sufficiently changed. Figure 9 represents the initial real lens zoom system combined due to the zooming locus listed in Table 3. As compared Fig. 6 to Fig. 9, the agreement for the first-order properties between both zoom systems is complete. This design procedure results in a real lens zoom system equivalent to the lens module zoom system. Table 3 shows the first-order quantities and zooming loci of an initial real lens zoom system.

FIG. 9.An 8x initial real lens zoom system with a fixed compensator realized by an FTL.

TABLE 3.First-order properties and zooming loci of an initial real zoom system with an FTL (in mm)

5.2. Optimized Design for Zoom System with an FTL

In the initial design of Fig. 9, to meet the current specifications for a zoom camera, the aperture and the field size should be increased. The f-numbers are extended to F/3.5 at wide and to F/4.5 at tele positions. The half image size should be 2.2 mm for a 1/4-inch CMOS image sensor. In order to improve the overall performance in an extended aperture and field system, we balance the aberrations of the starting data by using a lens design program.

Figure 10 illustrates the sag of the finally designed FTL at various positions, and Table 4 lists its design data. To reduce the magnitude of the sag’s variation at the FTL in this study, the focal lengths of an FTL are set to be the same at wide and tele positions. The variation of the sag from a wide to narrow field is less than 0.189 mm. It is such a small value that this configuration can realize a simple and mechanically stable zoom system.

FIG. 10.Variations for sag of the FTL with zoom position.

TABLE 4.Design data for the FTL in an aberration-balanced zoom system (in mm)

The layout of the finally designed zoom system is shown in Fig. 11. This system consists of 11 elements including an FTL and three aspherical lenses. The maximum diameter of the front group is 17.4 mm. Aberrations are significantly reduced. From Fig. 12, the modulation transfer function (MTF) at 180 lp/mm is more than 33% over all fields at three positions. The ratio of relative illuminations (RI) measured at margin fields is more than 57.1% over all positions, and distortions are sufficiently balanced, as shown in Fig. 13. Figure 14 illustrates the lateral color aberrations with zoom position, which are less than 3 μm within 0.7 fields.

FIG. 11.Layout of an aberration-balanced zoom system with an FTL at the fourth group. (Ⓐ denotes the aspheric lenses).

FIG. 12.MTF characteristics of an aberration-balanced zoom system with zoom position.

FIG. 13.Distortion and relative illumination of an aberration-balanced zoom system with zoom position.

FIG. 14.Lateral color aberrations of an aberration-balanced zoom system with zoom position (in mm).

The variation of the chief ray angle of incidence (AOI) from a wide to narrow field is less than 2 degrees. Because that is an extremely small value, a stable image quality for zooming can be realized. The total track of the zoom lens, even at a high zoom ratio of 8x, is less than 29 mm, which results in a compact zoom camera. Consequently, the performance of this zoom system satisfies current requirements for a zoom camera.

 

VI. CONCLUSION

For the design of an 8x four-group inner-focus zoom system having one moving group, a focus tunable lens has been suggested as a compensator, which is fixed for zooming.

In the initial design process, we obtained the powers of lens groups by paraxial design, and then setup the zoom system composed of four lens modules equivalent to each group. The numerical analysis of zoom locus has generally many difficulties in that lots of equations for various cases should be solved. To overcome these difficulties, we suggested the analysis of zoom locus using optimized lens modules. Here, four groups were replaced by equivalent lens modules. And to fix the image plane, we changed the powers of the fourth group at each position.

Next, four lens modules were converted to real lens groups step by step using an automatic design method. From this successive conversion process, the real lens of each group was quickly obtained by matching the first-order quantities of lens modules.

After aberration balancing, we obtained an 8x four-group inner-focus zoom system having one moving group by employing a focus tunable lens. This zoom lens has the focal lengths of 4 mm to 32 mm and the f-numbers of 3.5 at wide to 4.5 at tele zoom positions. Through this study, we showed the design process of a four-group inner-focus zoom system with a fixed compensator and its zoom locus analysis using optimized lens modules.