Steel and Composite Structures

  • 제20권4호
  • /
  • Pages.777-799
  • /
  • 2016
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Seismic response estimation of steel plate shear walls using nonlinear static methods

  • Dhar, Moon Moon (Department of Building, Civil and Environmental Engineering, Concordia University) ;
  • Bhowmick, Anjan K. (Department of Building, Civil and Environmental Engineering, Concordia University)
  • 투고 : 2015.10.09
  • 심사 : 2015.12.09
  • 발행 : 2016.03.20
⟨ 이전 논문 다음 논문 ⟩

초록

One of the major components for performance based seismic design is accurate estimation of critical seismic demand parameters. While nonlinear seismic analysis is the most appropriate analysis method for estimation of seismic demand parameters, this method is very time consuming and complex. Single mode pushover analysis method, N2 method and multi-mode pushover analysis method, modal pushover analysis (MPA) are two nonlinear static methods that have recently been used for seismic performance evaluation of few lateral load-resisting systems. This paper further investigates the applicability of N2 and MPA methods for estimating the seismic demands of ductile unstiffened steel plate shear walls (SPSWs). Three different unstiffened SPSWs (4-, 8-, and 15-storey) designed according to capacity design approach were analysed under artificial and real ground motions for Vancouver. A comparison of seismic response quantities such as, height-wise distribution of floor displacements, storey drifts estimated using N2 and MPA methods with more accurate nonlinear seismic analysis indicates that both N2 and MPA procedures can reasonably estimates the peak top displacements for low-rise SPSW buildings. In addition, MPA procedure provides better predictions of inter-storey drifts for taller SPSW. The MPA procedure has been extended to provide better estimate of base shear of SPSW.

키워드

참고문헌

  1. ANSI/AISC (2010), Seismic Provisions for Structural Steel Buildings; American Institute of Steel Construction Inc., Chicago, IL, USA.
  2. Applied Technology Council (1996), Seismic Evaluation and Retrofit of Concrete Buildings; ATC-40, Seismic Safety Commission, State of California, CA, USA.
  3. ASCE (2010), Minimum Design Loads for Buildings and other Structures; American Society of Civil Engineers, VA, USA.
  4. Atkinson, G.M. (2009), Earthquake Time Histories Compatible with the 2005 NBCC Uniform Hazard Spectrum. URL: www.seismotoolbox.ca
  5. Behbahanifard, M., Gilbert, R., Grondin, Y. and Elwi, A.E. (2003), "Experimental and numerical investigation of steel plate shear walls", Department of Civil and Environmental Engineering, University of Alberta; Edmonton, Canada.
  6. Berman, J.W. and Bruneau, M. (2008), "Capacity design of vertical boundary elements in steel plate shear walls", Eng. J., 45(1), 57-71.
  7. Bhowmick, A.K., Driver, R.G. and Grondin, G.Y. (2008), "Nonlinear seismic analysis of steel plate shear walls considering strain rate and P-delta effects", J. Construct. Steel Res., 65(5), 1149-1159. https://doi.org/10.1016/j.jcsr.2008.08.003
  8. Bhowmick, A.K., Grondin, G.Y. and Driver, R.G. (2011), "Estimating fundamental periods of steel plate shear walls", Eng. Struct., 33(6), 1883-1893. https://doi.org/10.1016/j.engstruct.2011.02.010
  9. CEN. Eurocode 8 (2001), Design of Structures for Earthquake Resistance, Part-1; European Standard prEN 1998-1, Draft No. 4, European Committee for Standardization, Brussels, Belgium.
  10. Chintanapakdee, C. and Chopra, A.K. (2003), "Evaluation of modal pushover analysis using generic frames", Earthq. Eng. Struct. Dyn., 32(3), 417-442. https://doi.org/10.1002/eqe.232
  11. Chopra, A.K. and Goel, R.K. (2001), "A modal pushover analysis procedure to estimate seismic demans for buildings: Theory and preliminary evaluation", Pacific Earthquake Engineering Research Center; CA, USA.
  12. Chopra, A.K., Goel, R.K. and Chintanapakdee, C. (2004), "Evaluation of a modified MPA procedure assuming higher modes as elastic to estimates seismic demands", Earthq. Spectra, 20(3), 757-778. https://doi.org/10.1193/1.1775237
  13. CSA (2009), "Limit states design of steel structures", Canadian Standards Association, Toronto, ON, Canada.
  14. Driver, R.G., Kulak, G.L., Kennedy, D.J.L. and Elwi, A.E. (1998), "Cyclic test of four storey steel plate shear wall", J. Struct. Eng., ASCE, 124(2), 112-120. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:2(112)
  15. Fajfar, P. (1999), "Capacity spectrum method based on inelastic demand spectra", Earthq. Eng. Struct. Dyn., 28(9), 979-993. https://doi.org/10.1002/(SICI)1096-9845(199909)28:9<979::AID-EQE850>3.0.CO;2-1
  16. FEMA (1997), NEHRP Guidelines for the Seismic Rehabilitation of Buildings; FEMA-273, Applied Technology Council for the Building Seismic Safety Council, Washington, D.C., USA.
  17. FEMA (2005), Improvement of Nonlinear Static Seismic Analysis Procedures: FEMA-440, Applied Technology Council (ATC-55 Project), Washington, D.C., USA.
  18. Goel, R.K. and Chopra, A.K. (2005), "Role of higher-"Mode" pushover analysis in seismic analysis of the buildings", Earthq. Spectra, 21(5), 1027-1041. https://doi.org/10.1193/1.2085189
  19. Guo, L., Rong, Q., Ma, X. and Zhang, S. (2011), "Behavior of steel plate shear wall connected to frame beams only", Int. J. Steel Struct., 11(4), 467-479. https://doi.org/10.1007/s13296-011-4006-7
  20. John, A. and Halchuk, S. (2003), "Fourth generation seismic hazard maps of Canada: Values for over 650 Canadian localities intended for the 2005 national building code of Canada", Geological Survey of Canada, Ottawa, ON, Canada.
  21. Kalkan, E. and Kunnath, S.K. (2007), "Assessment of current nonlinear static procedures for seismic evaluation of buildings", Eng. Struct., 29(3), 305-316. https://doi.org/10.1016/j.engstruct.2006.04.012
  22. Lubell, A.S., Prion, H.G.L., Ventura C.E. and Rezai, M. (2000), "Unstiffened steel plate shear wall performance under cyclic load", J. Struct. Eng., ASCE, 126(4), 453-460. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:4(453)
  23. Miranda, E. and Bertero, V.V. (1994), "Evaluation of strength reduction factors for earthquake resistent design", Earthq. Spectra, 10(2), 357-379. https://doi.org/10.1193/1.1585778
  24. Naumoski, N., Murat S. and Kambiz, A.H. (2004), "Effects of scaling of earthquake excitations on the dynamic response of reinforced concrete frame buildings", Proceedings of the 13th World Conference on Earthquake Engineering, Vancouver, BC, Canada, August.
  25. NBCC (2010), National Building Code of Canada; Canadian Commission on Building and Fire Codes, National Research Council of Canada (NRCC), Ottawa, ON, Canada.
  26. Nguyen, A.H., Chintanapakdee, C. and Hayashikawa, T. (2010), "Assessment of current nonlinear static procedures for seismic evaluation of BRBF buildings", J. Construct. Steel Res., 66(8-9), 1118-1127. https://doi.org/10.1016/j.jcsr.2010.03.001
  27. PEER (2010), Next Generation Attenuation of Ground Motions Project (NGA) Database; Pacific Earthquake Engineering Research Center, Berkely, CA, USA.
  28. Qu, B. and Bruneau, M. (2010), "Capacity design of intermediate horizontal boundary elements of steel plate shear walls", J. Struct. Eng., 136 (6), 665-675. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000167
  29. Sabouri-Ghomi, S. and Sajjadi, S.R.A. (2012), "Experimental and theoretical studies of steel shear walls with and without stiffeners", J. Construct. Steel Res., 75, 152-159. https://doi.org/10.1016/j.jcsr.2012.03.018
  30. Thorburn, L.J., Kulak, G.L. and Montgomery, C.J. (1983), "Analysis of steel plate shear walls", Structural Report No. 107; Department of Civil and Environmental Engineering, University of Alberta, Edmonton, AB, Canada.
  31. Timler, P.A. and Kulak, G.L. (1983), "Experimental study of steel plate shear walls", Structural Engineering Report No. 114; Department of Civil Engineering, University of Alberta, Edmonton, AB, Canada.
  32. Topkaya, C. and Atasoy, M. (2009), "Lateral stiffness of steel plate shear wall systems", Thin-Wall. Struct., 47(8-9), 827-835. https://doi.org/10.1016/j.tws.2009.03.006
  33. Topkaya, C. and Kurban, C.O. (2009), "Natural periods of steel plate shear wall systems", J. Construct. Steel Res., 65(3), 542-551. https://doi.org/10.1016/j.jcsr.2008.03.006
  34. Vidic, T., Fajfar, P. and Fischinger, M. (1994), "Consistent inelastic design spectra: Strength and displacement", Earthq. Eng. Struct. Dyn., 23(5), 507-521. https://doi.org/10.1002/eqe.4290230504

피인용 문헌

  1. Flexural behavior of beams in steel plate shear walls vol.23, pp.4, 2016, https://doi.org/10.12989/scs.2017.23.4.473
  2. Experimental and analytical study of steel slit shear wall vol.24, pp.6, 2016, https://doi.org/10.12989/scs.2017.24.6.741
  3. Hysteretic behavior of perforated steel plate shear walls with beam-only connected infill plates vol.25, pp.4, 2016, https://doi.org/10.12989/scs.2017.25.4.505
  4. Behavior of FRP-reinforced steel plate shear walls with various reinforcement designs vol.33, pp.5, 2019, https://doi.org/10.12989/scs.2019.33.5.729
  5. Seismic behavior investigation of the steel multi-story moment frames with steel plate shear walls vol.37, pp.1, 2016, https://doi.org/10.12989/scs.2020.37.1.091
  6. Hysteretic characteristics of steel plate shear walls: Effects of openings vol.76, pp.6, 2016, https://doi.org/10.12989/sem.2020.76.6.687
  7. Investigation of performance of steel plate shear walls with partial plate-column connection (SPSW-PC) vol.39, pp.1, 2016, https://doi.org/10.12989/scs.2021.39.1.109