Computers and Concrete

  • 제17권3호
  • /
  • Pages.423-433
  • /
  • 2016
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

A study of the replacement of desulphurization slag for sand to ready-mixed soil materials (RMSM)

  • Shiha, Yi-Fang (Department of Civil Engineering, National Kaohsiung University of Applied Sciences) ;
  • Tseng, Shih-Shong (Department of Civil Engineering, National Kaohsiung University of Applied Sciences) ;
  • Wang, Her-Yung (Department of Civil Engineering, National Kaohsiung University of Applied Sciences) ;
  • Wei, Chih-Ting (Department of Civil Engineering, National Kaohsiung University of Applied Sciences)
  • 투고 : 2015.08.29
  • 심사 : 2016.01.15
  • 발행 : 2016.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

After the industrial of steelmaking by-products are processed properly, they can be used in civil engineering, not only as a substitute for natural resources and to reduce costs, but also to provide environmental protection. This study used different amounts (10%, 20%, 30%, 40%,and 50%) of desulphurization slag to replace natural fine aggregates in ready-mixed soil materials, and tested the physical and fresh properties (slump, slump flow, tube flow, initial setting time, and bleeding) and hardened properties (compressive strength, ball drop, ultrasonic pulse velocity) of the materials. The variations between the performances of the materials with different mix proportions were discussed. When desulphurization slag is used in RMSM, the workability can be enhanced obviously significantly. When the replacement of desulphurization slag is 50%, the slump flow is increased by 110mm compared with the control group, and the initial setting time increases as the replacement increases, because of bleeding. When the replacement is 10% and 20%, the compressive strength at various ages is higher than that of the control group. When the replacement is 10%, the compressive strength at 7 days is higher than that of the control group by 60%, and the ultrasonic pulse velocity is proportional to the compressive strength, which increases with age and decrease as the replacement increases. An appropriate replacement can effectively accelerate construction, and allow projects to be finished ahead of schedule; therefore, an appropriate replacement, is applicable for ready-mixed soil materials.

키워드

참고문헌

  1. ACI-229R (2005), "Controlled-low strength materials (reproved 2005)", Farmington Hills (MI).
  2. ACI 229R-94 (1994), "Report: Controlled Low Strength Materials (CLSM)", Concrete International.
  3. ASTM C150 (2005), "Standard Specification for Portland Cement".
  4. ASTM C232 (2007), "Standard Test Method for Bleeding of Concrete".
  5. ASTM C33 (2003), "Standard Specification for Concrete Aggregates".
  6. ASTM C39 (2005), "Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens".
  7. ASTM C403 (1999), "Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance".
  8. ASTM C597 (2002), "Standard Test Method for Pulse Velocity Through Concrete".
  9. ASTM D6023 (2007), "Standard Test Method for Density (Unit Weight), Yield, Cement Content, and Air Content (Gravimetric) of Controlled Low-Strength Material (CLSM)".
  10. ASTM D6024 (2002), "Standard Test Method for Ball Drop on Controlled Low Strength Material (CLSM) to Determine Suitability for Load Application".
  11. ASTM D6103 (1997), "Standard Test Method for Flow Consistency of Controlled Low Strength Material (CLSM).
  12. Blanco, A., Pujadas, P., Cavalaro, S.H.P. and Aguado, A. (2014), "Methodology for the design of controlled low-strength materials. Application to the backfill of narrow trenches", Constr. Build. Mater., 72, 23-30. https://doi.org/10.1016/j.conbuildmat.2014.09.008
  13. Bouzalakos, S., Dudeney, A.W.L. and Chan, B.K.C. (2013), "Formulating and optimizing the compressive strength of controlled low-strength materials containing mine tailings by mixture design and response surface methods", Miner. Eng., 53, 48-56. https://doi.org/10.1016/j.mineng.2013.07.007
  14. Chen, J.H. (2012), "Study on engineering properties of ready-mixed soil material with applied of recycled materials", Master Thesis, National Kaohsiung University of Applied Sciences.
  15. Chen, J.W. and Chang, C.F. (2006), "Development and application of the ready-mixed soil material", J. Mater. Civ. Eng., 18(6), 722-729.
  16. Energy Check and Energy Conservation Case Manual-Cement Industry, Energy Information Network, http://emis.erl.itri.org.tw/other/techbook/list.asp.
  17. Environmental Protection Administration, http://www.epa.gov.tw/mp.asp?mp=epa.
  18. Finney, A.J., Shorey, E.F. and Anderson, J. (2008), "Use of native soil in place of aggregate in controlled low strength material (CLSM)", International Pipelines Conference, Atlanta, Georgia, United States.
  19. Green, B.H. (1999), "Development of soil-based controlled low-strength materials".
  20. Howard, A. (1994), "Soil-cement slurry pipe embedment in controlled low strength materials", SP-150. American Concrete Institute, 97-107.
  21. Lachemi, M., Hossain, K.M.A., Shehata, M. and Thaha, W. (2008), "Controlled low strength materials incorporating cement kiln dust from various sources", Cement Concrete Compos., 30(5), 381-92. https://doi.org/10.1016/j.cemconcomp.2007.12.002
  22. Lachemi, M.S., Ahmaran, M., Hossain, K.M.A., Lotfy, A. and Shehata, M. (2010), "Properties of controlled low-strength materials incorporating cement kiln dust and slag", Cement Concrete Compos., 32(8), 623-629. https://doi.org/10.1016/j.cemconcomp.2010.07.011
  23. Lin, J.S. (2004), "Research on engineering properties of ready-mixed soil", Master Thesis, National Cheng Kung University.
  24. Taha, R.A., Alnuaimi, A.S., Al-Jabri, K.S. and Al-Harthy, A.S. (2007), "Evaluation of controlled low strength materials containing industrial by-products", Build. Envir., 42(9), 3366-72. https://doi.org/10.1016/j.buildenv.2006.07.028
  25. Trejo, D., Folliard, K.J. and Du, L. (2004), "Sustainable development using controlled low strength material", Proceedings of the International Workshop on Sustainable Development and Concrete Technology, Beijing, China.
  26. Wang, H.Y. and Kuo, W.T. (2006), "The feasibility study of desulphurization slag powder as concrete Binder", Research Report, National Kaohsiung University of Applied Sciences.
  27. Weng, M.Y. (2006), "The feasibility of desulfurization/granulated slag resources recovery on the controlled low strength material without Portland cement", Master Thesis, National Kaohsiung University of Applied Sciences.
  28. Wu, J.Y. (2005), "Soil-based flowable fill for pipeline construction", Proceedings of Pipelines 2005: Optimizing Pipeline Design, Operations, and Maintenance in Today's Economy, Houston, Texas, USA.
  29. Wu, J.Y. and Lee, M.Z. (2011), "Beneficial reuse of construction surplus clay in CLSM", Int. J. Pavement Res. Tech., 4(5), 293-300.
  30. Yang, W.F. (1996), "Iron and steel industry waste of resources Casebook", Ministry of Economic Affairs Industrial Development Bureau.
  31. Zheng, R.B. (2002), "Fresh and hardened test of CLSM material, high-performance backfill material (CLSM) production", Taiwan construction Research Institute, 51-67.

피인용 문헌

  1. Study of the volume stability of slag cement mortar applied to desulfurization slag during high temperature operation vol.144, 2017, https://doi.org/10.1016/j.conbuildmat.2017.02.085