Structural Engineering and Mechanics

  • 제57권6호
  • /
  • Pages.1143-1156
  • /
  • 2016
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

The investigation crack problem through numerical analysis

  • Yaylaci, Murat (Department of Civil Engineering, Recep Tayyip Erdogan University)
  • 투고 : 2015.06.08
  • 심사 : 2016.02.17
  • 발행 : 2016.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

This paper presents a comparative study of finite element method (FEM) and analytical method for the plane problem of a layered composite containing an internal perpendicular crack in literature. The layered composite consists of two elastic layers having different elastic constants and heights. External load is applied to the upper elastic layer by means o a rigid punch and the lower elastic layer rests on two simple supports. Numerical simulations are realized by the world wide code ANYS software. Two dimensional analysis of the problem is carried out and the results are verified by comparison with solutions reported in literature. Main goal of the numerical simulation is to investigate the normal stress ${\sigma}_x$(0, y), stress intensity factors at the crack factor and the crack opening displacements.

키워드

참고문헌

  1. Adiyaman, G., Yaylaci, M. and Birinci, A. (2015), "Analytical and finite element solution of a receding contact problem", Struct. Eng. Mech., 54(1), 69-85. https://doi.org/10.12989/sem.2015.54.1.069
  2. Altunsaray, E. and Bayer, I. (2013), "Deflection and free vibration of symmetrically laminated quasiisotropic thin rectangular plates for different boundary conditions", Ocean Eng., 57, 197-222. https://doi.org/10.1016/j.oceaneng.2012.09.009
  3. ANSYS (2013), Swanson Analysis Systems Inc., Houston, PA, USA.
  4. Birinci, A. and Erdol, E. (2004), "A layered composite containing a crack in its lower layer loaded by a rigid stamp", Eur. J. Mech. A/Solid., 23, 909-924.
  5. Birinci, A., Adiyaman, G., Yaylaci, M. and Oner, E. (2015), "Analysis of continuous and discontinuous cases of a contact problem using analytical method and FEM", Latin Am. J. Solid. Struct., 12(9), 1771-1789. https://doi.org/10.1590/1679-78251574
  6. Bogdanski, S. (2002), "A rolling contact fatigue crack driven by Squeeze fluid film", Fatig. Fract. Eng. Mater. Struct., 21, 1061-71.
  7. Chaari, F., Fakhfakh, T. and Haddar, M. (2009), "Analytical modelling of spur gear tooth crack and influence on gear mesh stiffness", Eur. J. Mech. A/Solid., 28, 461-468. https://doi.org/10.1016/j.euromechsol.2008.07.007
  8. Delpero, T., Lepoittevin, G. and Sanchez, A. (2010), "Finite element modeling with ANSYS, centre of structure technologies", Swiss Federal Institute of Technology Zurich Swiss.
  9. Farjoo, M., Danie, l W. and Weehan, P.A. (2014), "Modeling a squat form crack on a rail laid on an elastic foundation", Eng. Fract. Mech., 85, 47-58.
  10. Figiel, L., Kaminski, M. and Lauke, B. (2004), "Analysis of a compression shear fracture test for curved interfaces in layered composites", Eng. Fract. Mech., 71, 967-980. https://doi.org/10.1016/S0013-7944(03)00158-9
  11. Hadju, S. (2014), "The investigation of the stress state near the crack tip of central cracks through numerical analysis", Procedia Eng., 69, 477-485. https://doi.org/10.1016/j.proeng.2014.03.015
  12. Isida, M. (1970), "On the determination of stress intensity factors for some common structural problems", Eng. Fract. Mech., 2, 61-79. https://doi.org/10.1016/0013-7944(70)90030-5
  13. Ji, J., Zhang, W., Zhao, W., Yuan, C. and Liu, Y. (2012), "Research of seismic testing and dynamic character of high-rise building structure based on ANSYS", Int. J. Digital Cont. Tech. Its Appl., 6(8), 63-71. https://doi.org/10.4156/jdcta.vol6.issue8.8
  14. Khan, D., Bhushan, A., Panda, S.K. and Biswas, K. (2013), "Elastic-plastic dynamic fracture analysis for stationary curved cracks", Finite Elem. Anal. Des., 73, 55-64. https://doi.org/10.1016/j.finel.2013.05.008
  15. Lee, J. (2009), "Identification of multiple cracks in a beam using vibration amplitudes", J. Sound Vib., 326, 205-212. https://doi.org/10.1016/j.jsv.2009.04.042
  16. Leverenz, R.K. (1972), "A finite element stress analysis of a crack in a bi-material plate", Int. J. Fract. Mech., 8, 311-24. https://doi.org/10.1007/BF00186130
  17. Oner, E., Yaylaci, M. and Birinci, A. (2015), "Analytical solution of a contact problem and comparison with the results from FEM", Struct. Eng. Mech., 54(4), 607-622. https://doi.org/10.12989/sem.2015.54.4.607
  18. Pandya, Y. and Parey, A. (2013), "Failure path based modified gear mesh stiffness for spur gear pair with tooth root crack", Eng. Fail. Anal., 27, 286-96. https://doi.org/10.1016/j.engfailanal.2012.08.015
  19. Papadopoulos, G.A., Badalouka, V. and Souyiannis, J. (2008), "Experimental study of the reduction at crack-tip stress intensity factor $K_1$ by bonded patches", Lett. Fract. Micromech., 149, 199-205.
  20. Qiao, P. and Wang, J. (2004), "Partial Mechanics and fracture of crack tip deformable bi-material interface", Int. J. Solid. Struct., 41, 7423-7444. https://doi.org/10.1016/j.ijsolstr.2004.06.006
  21. Shao, R., Dong, F., Wang, W. and Jia, P. (2013), "Influence of cracks on dynamic characteristics and stress intensity factor of gears", Eng. Fail. Anal., 32, 63-80. https://doi.org/10.1016/j.engfailanal.2013.03.008
  22. Sabliov, C.M., Salvi, D.A. and Boldor, D. (2007), "High frequency electromagnetism, heat transfer and fluid flow coupling in ANSYS multiphysics", IMPI, 4(4), 5-17.
  23. Yaylaci, M., O ner, E. and Birinci, A. (2014), "Comparison between analytical and ANSYS calculations for a receding contact", Am. Soc. Civil Eng., ASCE, 140(9), 71-80.
  24. Zandi, Y. and Akpinar, M.V. (2012), "Evaluation of internal resistance in asphalt concretes", Int. J. Concrete Struct. Mater., 6(4), 247-250. https://doi.org/10.1007/s40069-012-0021-0

피인용 문헌

  1. Contact problem for a stringer plate weakened by a periodic system of variable width slots vol.62, pp.6, 2016, https://doi.org/10.12989/sem.2017.62.6.719
  2. Experimental and numerical investigation of the effect of sample shapes on point load index vol.13, pp.6, 2017, https://doi.org/10.12989/gae.2017.13.6.1045
  3. The effect of ball size on the hollow center cracked disc (HCCD) in Brazilian test vol.22, pp.4, 2016, https://doi.org/10.12989/cac.2018.22.4.373
  4. Simulation of the tensile behaviour of layered anisotropy rocks consisting internal notch vol.69, pp.1, 2016, https://doi.org/10.12989/sem.2019.69.1.051
  5. Investigation of shear behavior of soil-concrete interface vol.23, pp.1, 2016, https://doi.org/10.12989/sss.2019.23.1.081
  6. The continuous-discontinuous Galerkin method applied to crack propagation vol.23, pp.4, 2016, https://doi.org/10.12989/cac.2019.23.4.235
  7. Experimental investigating the properties of fiber reinforced concrete by combining different fibers vol.25, pp.6, 2020, https://doi.org/10.12989/cac.2020.25.6.509
  8. Numerical simulation and experimental investigation of the shear mechanical behaviors of non-persistent joint in new shear test condition vol.26, pp.3, 2020, https://doi.org/10.12989/cac.2020.26.3.239
  9. Influences of porosity distributions and boundary conditions on mechanical bending response of functionally graded plates resting on Pasternak foundation vol.38, pp.1, 2016, https://doi.org/10.12989/scs.2021.38.1.001
  10. Relationship between point load index and mode II fracture toughness of granite vol.28, pp.1, 2021, https://doi.org/10.12989/cac.2021.28.1.025
  11. An efficient higher order shear deformation theory for free vibration analysis of functionally graded shells vol.40, pp.2, 2016, https://doi.org/10.12989/scs.2021.40.2.307
  12. Numerical simulation on the crack initiation and propagation of coal with combined defects vol.79, pp.2, 2016, https://doi.org/10.12989/sem.2021.79.2.237
  13. Z shape joints under uniaxial compression vol.12, pp.2, 2016, https://doi.org/10.12989/acc.2021.12.2.105
  14. A coupled experimental and numerical simulation of concrete joints' behaviors in tunnel support using concrete specimens vol.28, pp.2, 2021, https://doi.org/10.12989/cac.2021.28.2.189
  15. Influence of non-persistent joint sets on the failure behaviour of concrete under uniaxial compression test vol.28, pp.3, 2016, https://doi.org/10.12989/cac.2021.28.3.289
  16. Minimum contact stress modification for profile curve design defects in the beam-spring-cone docking mechanism vol.235, pp.22, 2016, https://doi.org/10.1177/09544062211003625