DOI QR코드

DOI QR Code

Bolted T-stubs: A refined model for flange and bolt fracture modes

  • Francavilla, Antonella B. (Department of Civil Engineering, Salerno University) ;
  • Latour, Massimo (Department of Civil Engineering, Salerno University) ;
  • Piluso, Vincenzo (Department of Civil Engineering, Salerno University) ;
  • Rizzano, Gianvittorio (Department of Civil Engineering, Salerno University)
  • 투고 : 2015.02.27
  • 심사 : 2015.10.21
  • 발행 : 2016.02.10

초록

It is well known that, in order to accurately predict the behaviour of steel structures a requirement the definition of the mechanical behaviour of beam-to column joints is of primary importance. This goal can be achieved by means of the so-called component method, which, in order to obtain the whole behaviour of connections, provides to break up joints in basic components of deformability and resistance. One of the main joint components used to model bolted connections is the so-called equivalent T-stub in tension, which is normally used to predict the behaviour of bolted plates in bending starting from the behaviour of the single bolt rows. In past decades, significant research efforts have been devoted to the prediction of the behaviour of bolted T-stubs but, to date, no particular attention has been devoted to the characterization of their plastic deformation capacity. To this scope, the work presented in this paper, taking into account the existing technical literature, proposes a new theoretical model for predicting the whole behaviour up to failure of bolted T-stubs under monotonic loading conditions, including some complexities, such as the bolt/plate compatibility requirement and the bolt fracture, which are necessary to accurately evaluate the ultimate displacement. After presenting the advances of the proposed approach, a comparison between theoretical and experimental results is provided in order to verify its accuracy.

키워드

참고문헌

  1. Abidelah, A., Bouchair, A. and Kerdal, D. (2014), "Influence of the flexural rigidity of the bolt on the behavior of the T-stub steel connection", Eng. Struct., 81, 181-194. https://doi.org/10.1016/j.engstruct.2014.09.041
  2. Beg, D., Zupancic, E. and Vayas, I. (2004), "On the rotation capacity of moment connections", J. Construct. Steel Res., 60(3-5), 601-620. https://doi.org/10.1016/S0143-974X(03)00132-9
  3. Bernuzzi, C., Zandonini, R. and Zanon, P. (1996), "Experimental analysis and modelling of semi-rigid steel joints under cyclic reversal loading", J. Construct. Steel Res., 38(2), 95-123. https://doi.org/10.1016/0143-974X(96)00013-2
  4. Bravo, M. and Herrera, R. (2014), "Performance under cyclic load of built-up T-stubs for double T moment connections", J. Construct. Steel Res., 103, 117-130. https://doi.org/10.1016/j.jcsr.2014.08.005
  5. CEN (2005a), Eurocode 3: Design of steel structures-Part 1-1: General rules and rules for buildings, s.l.:s.n.
  6. CEN (2005b), Eurocode 3: Design of steel structures-Part 1-8: Design of joints, s.l.:s.n.
  7. Davids, E., Troxell, G. and Hanck, G. (1982), The Testing of Engineering Materials, McGraw-Hill, New York, NY, USA.
  8. Douty, T. and McGuire, W. (1965), "High strength bolted moment connections", J. Struct. Div., 91(2), 101-128.
  9. Faella, C., Piluso, V. and Rizzano, G. (1998), "Experimental analysis of bolted connections: Snug versus preloaded bolts", J. Struct. Eng., 124(7), 765-774. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:7(765)
  10. Faella, C., Piluso, V. and Rizzano, G. (2000), Structural Steel Semi-Rigid Connections, CRC Press, Boca Raton, FL, USA.
  11. Fontana (2004), Prescrizioni Tecniche, s.l.: s.n.
  12. Girao Coelho, A.M., Bijlaard, F. and Simoes Da Silva, L. (2004a), "Experimental assessment of the ductility of extended end plate connections", Eng. Struct., 26(9), 1185-1206. https://doi.org/10.1016/j.engstruct.2000.09.001
  13. Girao Coelho, A.M.G., da Silva, L.S. and Bijlaard, F.S.K. (2004b), "Characterization of the nonlinear behavior of single bolted T-tub connections", Connections in Steel Structures V, Amsterdam, The Netherlands, pp. 53-64.
  14. Hantouche, E. and Abboud, N. (2014), "Stiffness modeling of bolted thick built-up T-stub connections including secondary prying effect", J. Construct. Steel Res., 95, 279-289. https://doi.org/10.1016/j.jcsr.2013.12.012
  15. Hantouche, E., Kukreti, A. and Rassati, G. (2012a), "Investigation of secondary prying in thick built-up Tstub connections using nonlinear finite element modeling", Eng. Struct., 36, 113-122. https://doi.org/10.1016/j.engstruct.2011.11.030
  16. Hantouche, E., Kukreti, A., Rassati, G. and Swanson, J. (2012b), "Built-up T-stub connections for moment resisting frames: Experimental and finite element investigation for prequalification", Eng. Struct., 43, 139-148. https://doi.org/10.1016/j.engstruct.2012.05.015
  17. Hantouche, E., Kukreti, A., Rassati, G. and Swanson, J. (2013), "Modified stiffness model for thick flange in built-up T-stub connections", J. Construct. Steel Res., 81, 76-85. https://doi.org/10.1016/j.jcsr.2012.11.009
  18. Hu, J., Leon, R. and Park, T. (2012), "Mechanical models for the analysis of bolted T-stub connections under cyclic loads", J. Construct. Steel Res., 78, 45-57. https://doi.org/10.1016/j.jcsr.2012.05.011
  19. Iannone, F., Latour, M., Piluso, V. and Rizzano, G. (2011), "Experimental analysis of bolted steel beam-tocolumn connections: Component identification", J. Earthq. Eng., 15(2), 214-244. https://doi.org/10.1080/13632461003695353
  20. Jaspart, J. (1991), "Etude de la Semi-rigidite Des Noeuds Poutre-Colonne et son Influence sur la Resistance et la Stabilite des Ossature en Acier", Ph.D. Tesis; University of Liege, Liege, Belgium.
  21. Kulak, G., Fisher, J. and Struik, J. (1987), Guide to Design Criteria for Bolted and Riveted Joints, John Wiley & Sons.
  22. Latour, M. and Rizzano, G. (2013), "A theoretical model for predicting the rotational capacity of steel base joints", J. Construct. Steel Res., 91, 88-99.
  23. Latour, M., Piluso, V. and Rizzano, G. (2011a), "Cyclic modeling of bolted beam-to-column connections: Component approach", J. Earthq. Eng., 15(4), 537-563. https://doi.org/10.1080/13632469.2010.513423
  24. Latour, M., Piluso, V. and Rizzano, G. (2011b), "Experimental analysis of innovative dissipative bolted double split tee beam-to-column connections", Steel Construct., 4(2), 53-64. https://doi.org/10.1002/stco.201110009
  25. Latour, M., Piluso, V. and Rizzano, G. (2014), "Rotational behaviour of column base plate connections: Experimental analysis and modelling", Eng. Struct., 68, 14-23. https://doi.org/10.1016/j.engstruct.2014.02.037
  26. Lemonis, M.E. and Gantes, C.J. (2006), "Incremental modeling of T-stub connections", J. Mech. Mater. and Struct., 1(7), 1135-1159. https://doi.org/10.2140/jomms.2006.1.1135
  27. Leon, R. and Swanson, J. (2000), "Bolted steel connections: Tests on T-stub components", J. Struct. Eng., 126(1), 50-56. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:1(50)
  28. Malvern, L. (1969), Introduction of the Mechanics of the Continuous Medium, Prentice-Hall, NJ, USA.
  29. Nair, R.S., Birkemoe, P.C. and Munse, W.H. (1974), "High strength bolts subject to tension and prying", J. Struct. Div., ASCE, 100(2), 351-372.
  30. Piluso, V. and Rizzano, G. (2008), "Experimental analysis and modelling of bolted T-stubs under cyclic loads", J. Construct. Steel Res., 64(6), 655-669. https://doi.org/10.1016/j.jcsr.2007.12.009
  31. Piluso, V., Faella, C. and Rizzano, G. (2001), "Ultimate behavior of bolted T-stubs. Part I: Theoretical model", J. Struct. Eng. ASCE, 127(6), 686-693. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:6(686)
  32. Pozzati, P. (1980), Teoria e Tecnica delle strutture, UTET, Torino, Italy.
  33. Reinosa, J., Loureiro, A., Gutierrez, R. and Lopez, M. (2013), "Analytical frame approach for the axial stiffness prediction of preloaded T-stubs", J. Construct. Steel Res., 90, 156-163. https://doi.org/10.1016/j.jcsr.2013.07.030
  34. RILEM (1990), "Draft recommendation-Tension testing of metallic structural materials for determining stress-strain relations under monotonic and uniaxial tensile loading", Mater. Struct., 23(1), 35-46. https://doi.org/10.1007/BF02472996
  35. Saberi, V., Gerami, M. and Kheyroddin, A. (2014), "Comparison of bolted end plate and T-stub connection sensitivity to component thickness", J. Construct. Steel Res., 98, 134-145. https://doi.org/10.1016/j.jcsr.2014.02.012
  36. Swanson, J. (1999), "Characterization of the strength, stiffness and ductility behavior of T-stub connections", Ph.D. Thesis; Georgia Institute of Technology.
  37. Swanson, J. (2002), "Ultimate strength prying models for bolted T-stub connections", Eng. J., 3, 136-147.
  38. Swanson, J. and Leon, R. (2001), "Stiffness modeling of bolted T-stub connection components", J. Struct. Eng., 127(5), 498-505. https://doi.org/10.1061/(ASCE)0733-9445(2001)127:5(498)
  39. Takhirov, S.M. and Popov, E.P. (2002), "Bolted large seismic steel beam-to-column connections Part 2: Numerical nonlinear analysis", Eng. Struct., 43(12), 1535-1545.
  40. Yee, Y. and Melchers, R. (1986), "Moment-rotation curves for bolted connections", J. Struct. Eng. ASCE, 112(3), 615-635. https://doi.org/10.1061/(ASCE)0733-9445(1986)112:3(615)
  41. Zoetemeijer, P. (1974), "A design method for the tension side of statically loaded, bolted beam-to-column connections", Heron, 20(1), 1-59.

피인용 문헌

  1. 14.01: Influence of beam-to-column joints on the robustness of earthquake-resistant moment-resistant frames vol.1, pp.2-3, 2017, https://doi.org/10.1002/cepa.442
  2. Numerical cyclic behavior of T-RBS: A new steel moment connection vol.21, pp.6, 2016, https://doi.org/10.12989/scs.2016.21.6.1251
  3. Numerical estimation for initial stiffness and ultimate moment of T-stub connections vol.141, 2018, https://doi.org/10.1016/j.jcsr.2017.11.008
  4. Simplified criteria for finite element modelling of European preloadable bolts vol.24, pp.6, 2017, https://doi.org/10.12989/scs.2017.24.6.643
  5. On the Robustness of Earthquake-Resistant Moment-Resistant Frames: Influence of Innovative Beam-to-Column Joints vol.12, pp.0, 2018, https://doi.org/10.2174/1874836801812010101
  6. Ultimate Performance of External End-plate Bolted Joints Under Column Loss Scenario Accounting for the Influence of the Transverse Beam vol.12, pp.0, 2016, https://doi.org/10.2174/1874836801812010132
  7. The mechanical behaviour of T-stubs with four bolts per row vol.172, pp.12, 2016, https://doi.org/10.1680/jstbu.18.00055
  8. Deformation Maps for Bolted T-Stubs vol.146, pp.5, 2016, https://doi.org/10.1061/(asce)st.1943-541x.0002584
  9. Behaviour and design of Grade 10.9 high-strength bolts under combined actions vol.35, pp.3, 2016, https://doi.org/10.12989/scs.2020.35.3.327
  10. Thermoelastic effect on inter-laminar embedded delamination characteristics in Spar Wingskin Joints made with laminated FRP composites vol.35, pp.3, 2020, https://doi.org/10.12989/scs.2020.35.3.439
  11. The Design of a Real-Scale Steel Moment-Resisting Frame for Pseudo-Dynamic Earthquake Testing vol.14, pp.1, 2016, https://doi.org/10.2174/1874836802014010174
  12. Stiffness Prediction of Connections between CHS Tubes and Externally Welded I-Beams: FE Analyses and Analytical Study vol.13, pp.13, 2016, https://doi.org/10.3390/ma13133030
  13. Seismic Behavior of Moment-Resisting Frames with Conventional and Innovative Connections vol.12, pp.12, 2016, https://doi.org/10.3390/sym12122091
  14. Moment-rotation model of endplate blind bolted joints with CFST column vol.176, pp.None, 2021, https://doi.org/10.1016/j.jcsr.2020.106446
  15. Generalised Component Method-based finite element analysis of steel frames vol.187, pp.None, 2016, https://doi.org/10.1016/j.jcsr.2021.106949
  16. Experimental response of a large-scale two-storey steel building equipped with low-yielding friction joints vol.152, pp.None, 2022, https://doi.org/10.1016/j.soildyn.2021.107022