DOI QR코드

DOI QR Code

A review of the effects of rock properties on waterjet rock cutting performance

암석물성이 워터젯 암석절삭 성능에 미치는 영향고찰

  • Oh, Tae-Min (Underground Space Department, Korea Institute of Geoscience and Mineral Resources(KIGAM)) ;
  • Park, Eui-Seob (Underground Space Department, Korea Institute of Geoscience and Mineral Resources(KIGAM)) ;
  • Cheon, Dae-Sung (Underground Space Department, Korea Institute of Geoscience and Mineral Resources(KIGAM)) ;
  • Cho, Gye-Chun (Department of Civil and Environmental Engineering, KAIST) ;
  • Joo, Gun-Wook (Department of Civil and Environmental Engineering, KAIST)
  • 오태민 (한국지질자원연구원, 지하공간연구실) ;
  • 박의섭 (한국지질자원연구원, 지하공간연구실) ;
  • 천대성 (한국지질자원연구원, 지하공간연구실) ;
  • 조계춘 (한국과학기술원, 건설및환경공학과) ;
  • 주건욱 (한국과학기술원, 건설및환경공학과)
  • Received : 2015.09.01
  • Accepted : 2015.09.17
  • Published : 2015.09.30

Abstract

The rock fracturing during waterjet cutting is very complicated because rock is inhomogeneous and anisotropic, compared with artificial materials (e.g., metal or glass). Thus, it is very important to verify the effects of rock properties on waterjet rock cutting performance. Properties affecting the rock cutting efficiency have been variously described in the literature, depending on the experimental conditions (e.g., water pressure, abrasive feed rate, or standoff distance) and rock-types studied. In this study, a rock-property-related literature review was performed to determine the key properties important for waterjet rock cutting. Porosity, uniaxial compressive strength, and hardness of the rock were determined to be the key properties affecting waterjet rock cutting. The results of this analysis can provide the basic knowledge to determine the cutting efficiency of waterjet rock cutting technology for rock excavation-related construction.

암석은 인공적인 재료(금속, 유리)에 비해 불균질하고 이방성을 가지고 있기 때문에 워터젯 절삭시 매우 복잡하게 파쇄되는 특성을 가진다. 워터젯 절삭시 암석특성에 따라 절삭성능이 결정되므로 물성에 대한 영향을 파악하는 것은 매우 중요하다. 워터젯 절삭효율에 영향을 미치는 물성은 선행문헌의 실험조건(수압, 연마재 투입량, 이격거리 등) 및 암종에 따라 다양하게 제시되고 있다. 본 연구에서는 워터젯 시스템을 이용한 암석절삭에 있어서 물성영향에 대해 문헌연구를 실시하고 중요 물성을 분석하였다. 선행문헌 연구를 통해 암석의 공극율, 일축압축강도, 경도가 워터젯 암석 절삭에 있어서 중요한 물성으로 도출되었다. 분석결과는 향후 워터젯 절삭 기술을 이용한 터널공사시, 암반특성에 따른 굴착효율을 예측하기 위한 기초지식을 제공할 수 있을 것이다.

Keywords

References

  1. Agus, M., Bortolussi, A., Ciccu, R., Kim, W.M., Manca, P.P. (1993), "The influence of rock properties on waterjet performance.", Poceeding of the 1993 American Water Jet Conference, Seattle, U.S.A, pp. 427-442.
  2. Aydin, G., Karakurt, I., Aydiner, K. (2013), "Prediction of the cut depth of granitic rocks machined by abrasive waterjet (AWJ).", Rock mechanics and rock engineering, Vol. 46, No. 5, pp. 1223-1235. https://doi.org/10.1007/s00603-012-0307-1
  3. Ciccu, R., Grosso, B. (2014), "Improvement of disc cutter performance by water jet assistance.", Rock mechanics and rock engineering, Vol. 47, No. 2, pp. 733-744. https://doi.org/10.1007/s00603-013-0433-4
  4. Crow, S.C. (1973), "A theory of hydraulic rock cutting.", International journal of rock mechanics and mining science, Vol. 10, pp. 567-584. https://doi.org/10.1016/0148-9062(73)90006-5
  5. Curbach M., Eibl J. (1990), "Crack velocity in concrete. engineering fracture mechanics.", Vol. 35, pp. 321-326. https://doi.org/10.1016/0013-7944(90)90210-8
  6. Eberhardt, E., Stimpson, B., Stead, D. (1999), "Effects of grain size on the initiation and propagation thresholds of stress-induced brittle fractures.", Rock Mechanics and Rock Engineering, Vol. 32, No. 2, pp. 81-99. https://doi.org/10.1007/s006030050026
  7. Engin, I.C. (2012), "A correlation for predicting the abrasive water jet cutting depth for natural stones.", South African Journal of Science, Vol. 108, No. 9-10, pp. 1-11.
  8. Engin, I.C., Bayram, F., Yasitli, N.E. (2013), "Experimental and statistical evaluation of cutting methods in relation to specific energy and rock properties.", Rock mechanics and rock engineering, Vol. 46, No. 4, pp. 755-766. https://doi.org/10.1007/s00603-012-0284-4
  9. Evans, A.G., Gulden, M.E., Rosenblatt, M. (1978), "Impact damage in brittle materials in the elasticplastic response régime", Proc. R. Soc. Lond. Series. A., Vol. 361, pp. 343-365. https://doi.org/10.1098/rspa.1978.0106
  10. Grattan-Bellew, P.E., Vijay, M.M. (1986), "Influence of physical properties of rock on rate of penetration of a water-jet drill.", Can Mineral, Vol. 24, pp. 323-328.
  11. Jung, S.J., Prisbrey, K., Wu, G. (1994), "Prediction of rock hardness and drillability using acoustic emission signatures during indentation.", International journal of rock mechanics and mining sciences & geomechanics abstracts, Vol. 31, No. 5, pp. 561-567. https://doi.org/10.1016/0148-9062(94)90159-7
  12. Karakurt, I., Aydin, G., Aydiner, K. (2011), "Effect of the uniaxial compressive strength of the rock on the cutting performance of AWJ.", Proceeding of the 2011 American Water Jet Conference, Houston, U.S.A, Paper F1.
  13. Karakurt, I., Aydin, G., Aydiner, K. (2012), "An experimental study on the depth of cut of granite in abrasive waterjet cutting.", Materials and Manufacturing Processes, Vol. 27, No. 5, pp. 538-544. https://doi.org/10.1080/10426914.2011.593231
  14. Kim, J.G., Song, J.J. (2015), "Abrasive water jet cutting methods for reducing blast-induced ground vibration in tunnel excavation.", International Journal of Rock Mechanics and Mining Sciences, Vol. 75, pp. 147-158. https://doi.org/10.1016/j.ijrmms.2014.12.011
  15. Lu, Y., Tang, J., Ge, Z., Xia, B., Liu, Y. (2013), "Hard rock drilling technique with abrasive water jet assistance.", International Journal of Rock Mechanics and Mining Sciences, Vol. 60, pp. 47-56. https://doi.org/10.1016/j.ijrmms.2012.12.021
  16. Miranda, R.M., Lousa, P., Mouraz, M.A.J., Kim, T. (1993), "Abrasive waterjet cutting of Portuguese marbles.", In Proceedings of the 7th American water jet conference, Seattle, Washington, USA, pp. 443-457.
  17. Momber, A.W., Kovacevic, R. (1997), "Test parameter analysis in abrasive water jet cutting of rocklike materials.", International Journal of Rock Mechanics and Mining Sciences, Vol. 34, No. 1, pp. 17-25. https://doi.org/10.1016/S1365-1609(97)80030-5
  18. Momber, A.W. (2004), "Wear of rocks by water flow.", International Journal of Rock Mechanics and Mining Sciences Vol. 41, pp. 51-68. https://doi.org/10.1016/S1365-1609(03)00075-3
  19. Momber, A.W. (2014), "Effects of target material properties on solid particle erosion of geomaterials at different impingement velocities.", Wear, Vol. 319, No. 1, pp. 69-83. https://doi.org/10.1016/j.wear.2014.07.007
  20. Nakajima, Todoroki (1984), "Relationship of fracture toughness testing to breakability by water jet for rock.", Technical note of the port and harbour research institute, ministry of transport, Japan, Vol. 489 (In Japanese).
  21. Oh, T.M., Cho, G.C. (2012), "Effect of abrasive waterjet parameters on rock removal.", Journal of Korean Tunnelling and Underground Space Association, Vol. 14, No. 4, pp. 421-435. https://doi.org/10.9711/KTAJ.2012.14.4.421
  22. Oh, T.M., Cho, G.C., Ji, I.T. (2013), "Effects of free surface using waterjet cutting for rock blasting excavation.", Korean Tunnelling and Underground Space Association, Vol. 15, No. 1, pp. 49-57. https://doi.org/10.9711/KTAJ.2013.15.1.049
  23. Oh, T.M., Cho, G.C. (2014), "Characterization of effective parameters in abrasive waterjet rock cutting.", Rock Mechanics and Rock Engineering, Vol. 47, No. 2, pp. 745-756. https://doi.org/10.1007/s00603-013-0434-3
  24. Rescic, S., Tiano, P., Fratini, F., Manganelli, R. (2013), "The micro-sand blasting technique as a new tool for the evaluation of the state of conservation of natural stone and mortar surfaces.", European Journal of Environmental and Civil Engineering. Vol. 17, No. 2, pp. 113-127. https://doi.org/10.1080/19648189.2012.751227
  25. Singh, M.M., Huck, P.J. (1970), "Correlation of rock properties to damage effected by water jet.", In The 12th US Symposium on Rock Mechanics (USRMS), American Rock Mechanics Association, pp. 681-695.
  26. Summers, D.A. (1972), "Water jet cutting related to jet and rock properties.", In The 14th US Symposium on Rock Mechanics (USRMS), American Rock Mechanics Association, pp. 569-588.
  27. Summers, D.A. (1995), Waterjetting technology, E and FN Spon, pp. 8-13.
  28. Sunwoo, C., Choi, B.H., Ryu, C.H. (1994), "A study on the slot cutting in granite by high speed water jet.", Journal of Korean Society For Rock Mechanics, Vol. 4, No. 2, pp. 92-101.
  29. Verhoef, P.N., Kuipers, T.J., Verwaal, W. (1984), "The use of the sand-blast test to determine rock durability.", Bulletin of Engineering Geology and the Environment, Vol. 29, pp. 457-461.
  30. Xie, J., Tamaki, J. (2007), "Parameterization of micro-hardness distribution in granite related to abrasive machining performance.", Journal of Materials Processing Technology, Vol. 186, pp. 253-258. https://doi.org/10.1016/j.jmatprotec.2006.12.041
  31. Yavuz, H., Ugur, I., Demirdag, S. (2008), "Abrasion resistance of carbonate rocks used in dimension stone industry and correlations between abrasion and rock properties.", International Journal of Rock Mechanics and Mining Sciences, Vol. 45, No. 2, pp. 260-267. https://doi.org/10.1016/j.ijrmms.2007.04.003
  32. Zeng, J., Kim, T.J. (1996), "An erosion model of polycrystalline ceramics in abrasive waterjet cutting", Wear, Vol. 193, pp. 207-217. https://doi.org/10.1016/0043-1648(95)06721-3