Structural Engineering and Mechanics

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Minimum shear reinforcement ratio of prestressed concrete members for safe design

  • Park, Min-Kook (Department of Architectural Engineering, University of Seoul) ;
  • Lee, Deuck Hang (Department of Architectural Engineering, University of Seoul) ;
  • Ju, Hyunjin (Department of Architectural Engineering, University of Seoul) ;
  • Hwang, Jin-Ha (Department of Architectural Engineering, University of Seoul) ;
  • Choi, Seung-Ho (Department of Architectural Engineering, University of Seoul) ;
  • Kim, Kang Su (Department of Architectural Engineering, University of Seoul)
  • Received : 2014.12.01
  • Accepted : 2015.10.20
  • Published : 2015.10.25
⟨ Previous Next ⟩

Abstract

Design codes have specified the minimum shear reinforcement requirement for reinforced concrete (RC) and prestressed concrete (PSC) members to prevent brittle and premature shear failure. They are, however, very different from one another, and particularly, ACI318 code allows the required minimum shear reinforcement to be reduced in PSC members, compared to that in RC members, by specifying the additional equation for PSC members whose basis is not clear. In this paper, the minimum shear reinforcement ratio for PSC members was proposed, which can provide a sufficient reserved shear strength and deformation capacity. The proposed equation was also verified by the test results of PSC specimens lightly reinforced in shear, comparing to design codes and other proposed equations from previous studies.

Keywords

Acknowledgement

Supported by : National Research Foundation of Korea (NRF)

References

  1. ACI Committee 318 (2011), Building Code Requirements for Structural Concrete and Commentary (ACI 318M-11), American Concrete Institute, Farmington Hills, 503.
  2. ACI Committee 318 (2005), Building Code Requirements for Structural Concrete and Commentary (ACI 318M-05), American Concrete Institute, Farmington Hills, 436.
  3. ACI Committee 318 (1971), ACI Standard Building Code Requirements for reinforced Concrete (ACI 318-71), American Concrete Institute, 78.
  4. American Association of State Highway and Transportation Officials (2004), AASHTO LRFD Bridge Design Specifications, 3th ed., AASHTO, Washington, DC.
  5. Angelakos, D., Bentz, E. C. and Collins, M. P. (2001), "Effect of concrete strength and minimum stirrups on shear strength of large members", ACI Struct. J., 98(3), 290-300.
  6. Appa Rao, G. and Injaganeri, S.S. (2013), "Minimum shear reinforcement for optimum ductility of reinforced concrete beams," Int. J. Res. Eng. Tech., 2(10), 25-32.
  7. Architectural Institute of Japan (1998), Standard for Structural Design and Construction of Prestressed Concrete Structures, Architectural Institute of Japan, 473 pp.
  8. Architectural Institute of Japan (1991), Standard for Structural Calculation of Reinforced Concrete Structures, Architectural Institute of Japan.
  9. Avendano, A.R. and Bayrak, O. (2010), "Toward efficient shear reinforcement design limit in prestressed concrete beams", 3rd fib International Congress, Washington D.C., Proceeding CD, Paper No. 374. 1-13
  10. Avendano, A.R. and Bayrak, O. (2011), "Efficient shear reinforcement design limits for prestressed concrete beams," ACI Struct. J., 108(6), 689-697.
  11. CSA Committee A23.3-04 (2004), Design of Concrete Structures for Buildings (CAV3-A23.3-04), Canadian Standards Association, Canada.
  12. Collins, M. P. and Mitchell, D. (1991), Prestressed Concrete Structures, Prentice Hill.
  13. Comite Euro-International du Beton, CEB-FIP Model Code 1990, Thomas Telford, Lodon.
  14. Ghosh, S.K. (1986a), "Exceptions of precast prestressed concrete members to minimum reinforcement requirements", PCI J., 31(6), 74-91. https://doi.org/10.15554/pcij.11011986.74.91
  15. Ghosh, S.K. (1986b), "Summary of responses to a questionnaire on minimum reinforcement requirements for prestressed concrete members", PCI J., 31(6), 92-123. https://doi.org/10.15554/pcij.11011986.92.123
  16. Ghosh, S.K. (1987), "Shear reinforcement requirement for precast prestressed double-tee members," ACI Struct. J., 84(2), 287-292.
  17. Hawkins, N.M., Kuchma, D.A., Mast, R.F., Marsh, M.L. and Reineck, K.H. (2005), "Simplified Shear Design of Structural Concrete Members", NCHRP report 549, National Research Council, Washington, DC, Transportation Research Board.
  18. Johnson, M.K. and Ramirez, J.A. (1989), "Minimum shear reinforcement in beams with higher strength concrete", ACI Struct. J., 86(4), 376-382.
  19. KCI-M-07(2007), Design Specifications for Concrete Structures, Korea Concrete Institute.
  20. Kuchma, D.A. and Kim, K.S. (2001), "Stress limits and minimum reinforcement requirements in shear design provisions", Prog. Struct. Eng. Mater., 3(4), 317-325. https://doi.org/10.1002/pse.94
  21. Kuchma, D.A., Kim, K.S. and Hawkins, N.M. (2005), "NCHRP project 12-61, simplified shear design of structural concrete members", J. Tran. Res. Board, CD 11-S, 129-142.
  22. Kuchma, D., Hawkins, N.M., Kim, S., Sun, S. and Kim, K.S. (2008a), "Simplified shear provisions of the AASHTO LRFD Bridge Design Specifications", PCI J., 38(3), 53-73.
  23. Kuchma, D., Kim, K.S., Nagle, T.J., Sun, S. and Hawkins, N.M. (2008b), "Shear tests on high-strength prestressed bulb-tee girders: strengths and key observations", ACI Struct. J., 105(3), 358-367.
  24. Laskar, A., Hsu, T.T.C. and Mo, Y.L. (2010), "Shear strengths of prestressed concrete beams Part 1: experiments and shear design equations", ACI Struct. J., 107(3), 330-339.
  25. Lee, J.Y. and Yoon, S.H. (2003), "Evaluation of the minimum shear reinforcement ratio of reinforced concrete members", J. Korea Concrete Inst., 16(1), 43-53.
  26. Lee, J.Y. and Kim, U.Y. (2008), "Effect of longitudinal tensile reinforcement ratio and shear span-depth on minimum shear reinforcement in beams", ACI Struct. J., 105(2), 134-144.
  27. Lee, J.Y. and Hwang, H.B. (2010), "Maximum shear reinforcement of reinforced concrete beams", ACI Struct. J., 107(5), 580-588.
  28. Lyngberg, B.S. (1976), "Ultimate shear resistance of partially prestressed reinforced concrete I-beams", ACI J., 73(4), 214-222.
  29. MacGregor, J.G. and Wight, J.K. (2005), Reinforced Concrete Mechanics and Design, 4th Edition, Pearson Prentice Hall, Upper Saddle River, NJ.
  30. Nawy, E.G. (2006), Prestressed Concrete: A Fundamental Approach, Prentice Hall, 5th Edition.
  31. Olesen, S.E., Sozen, M.A. and Siess, C.P. (1965), "Investigation of prestressed reinforced concrete for highway bridges Part IV: strength in shear of beams with web reinforcement", Bulletin No. 295,Enfineering Experiment Station, University of Illinois, Urbana, IL.
  32. Ozcebe, G., Ersoy, U. and Tankut, T. (1999), "Evaluation of minimum shear reinforcement requirements for higher strength concrete", ACI Struct. J., 96(3), 361-369.
  33. Rahal, K.N. and Al-Shaleh, K. (2004), "Minimum transverse reinforcement in 65 MPa concrete beams", ACI Struct. J., 101(6), 872-878.
  34. Reineck, K.H., Kuchma, D.A., Kim, K.S. and Marx, S. (2003), "Shear database for reinforced concrete members without shear reinforcement", ACI Struct. J., 100(2), 240-249.
  35. Roller, J.J. and Russell, H.G. (1990), "Shear strength of high-strength concrete beams with web reinforcement", ACI Struct. J., 87(2), 191-198.
  36. Sneed, L.H. and Ramirez, J.A. (2009), "Evaluation of minimum shear reinforcement requirements in non-prestressed beams without distributed horizontal reinforcement", ACI Special Publication, SP-265-19, 405-425.
  37. Teoh, B.K., Mansur, M.A. and Wee, T.H. (2002), "Behavior of high-strength concrete I-beams with low shear reinforcement", ACI Struct. J., 99(3), 299-307.
  38. Yoon, Y.S., Cook, W.D. and Mitchell, D. (1996), "Minimum and high-strength concrete beams", ACI Struct. J., 93(5), 576-584.
  39. Zararis, P.D. (2010), "Shear strength and minimum shear reinforcement of reinforced concrete slender beams", ACI Struct. J., 100(2), 203-214.

Cited by

  1. A study about determination of preliminary design & minimum reinforcement ratios vol.17, pp.5, 2016, https://doi.org/10.12989/cac.2016.17.5.673
  2. 강도여유율을 고려한 프리스트레스트 콘크리트 보의 최소전단철근비 vol.33, pp.5, 2017, https://doi.org/10.5659/jaik_sc.2017.33.5.21
  3. Determination of minimum depth of prestressed concrete I-Girder bridge for different design truck vol.24, pp.4, 2015, https://doi.org/10.12989/cac.2019.24.4.303
  4. A stress field approach for the shear capacity of RC beams with stirrups vol.73, pp.5, 2015, https://doi.org/10.12989/sem.2020.73.5.515