Earthquakes and Structures

  • 제9권4호
  • /
  • Pages.875-891
  • /
  • 2015
  • /
  • 2092-7614(pISSN)
  • /
  • 2092-7622(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Determination of critical excitation in seismic analysis of structures

  • Kamgar, Reza (Department of Civil Engineering, Faculty of Engineering, Shahid Bahonar University of Kerman) ;
  • Rahgozar, Reza (Department of Civil Engineering, Faculty of Engineering, Shahid Bahonar University of Kerman)
  • 투고 : 2014.12.02
  • 심사 : 2015.05.03
  • 발행 : 2015.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

Earthquake can occur anywhere in the world and it is essential to design important members in special structures based on maximum possible forces that can be produced in them under severe earthquake. In addition, since the earthquake is an accidental phenomena and there are no similar earthquakes, therefore the possibility of strong earthquakes should be taken into account in earthquake-resistant design of important structures. Based on this viewpoint, finding the critical acceleration which maximizes internal forces is an essential factor in structural design. This paper proposes critical excitation method to compute the critical acceleration in design of important members in special structures. These critical accelerations are computed so that the columns' internal shear force at the base of the structure at each time step is maximized under constraints on ground motion. Among computed critical accelerations (of each time step), the one which produces maximum internal shear force is selected. A numerical example presents to show the efficiency of critical excitation method in determining the maximum internal shear force and base moment under variety of constraints. The results show that these method can be used to compute the resonant earthquake which have large enough effective duration of earthquake strong motion (between 12.86 sec to 13.38 sec) and produce the internal shear force and base moment for specific column greater than the same value for selected earthquakes in constructing the critical excitation (for different cases about 2.78 to 1.29 times the San Fernando earthquake). Therefore, a group of them can be utilized in developing the response spectrum for design of special structures.

키워드

참고문헌

  1. Abbas, A.M. (2006), "Critical seismic load inputs for simple inelastic structures", J. Sound. Vib., 296, 949-67. https://doi.org/10.1016/j.jsv.2006.03.021
  2. Abbas, A.M. and Manohar, C.S. (2002), "Critical spatially-varying earthquake load models for extended structures", J. Struct. Eng., ASCE, 29(1), 39-52.
  3. Anderson, J.C. and Bertero, V.V. (1987), "Uncertainties in establishing design earthquakes", J. Struct. Eng., ASCE, 113(8), 1709-1724. https://doi.org/10.1061/(ASCE)0733-9445(1987)113:8(1709)
  4. Arias, A. (1970), A measure of earthquake intensity: seismic design for nuclear power plants, MIT Press, Cambridge, MA.
  5. Arora, J.S. (2012), Introduction to Optimum Design, Elsevier, Academic Press, USA.
  6. Caleman, T., Branch, M.A. and Grace, A. (1999), Optimization Toolbox for the Use with Matlab: User's Guide, The Math Works Inc., USA.
  7. Chandler, A.M., Pappin, J.W. and Coburn, A.W. (1991), "Vulnerability and seismic risk assessment of buildings following the 1989 Newcastle, Australia earthquake", Bull. NZ. Soc. Earthq. Eng., 24(2), 116-138.
  8. COSMOS (2009) Consortium organizations for strong-motion observation systems. http://www.strongmotioncenter.org/vdc/scripts/default.plx
  9. Drenick, R.F. (1970), "Model-free design of aseismic structures", J. Eng. Mech., ASCE, 96(4), 483-493.
  10. Drenick, R.F. (1977), On a class of non-robust problems in stochastic dynamics, Stochastic Problems in Dynamics, Ed., B.L. Clarkson, Pitman, London.
  11. Fujita, K. Kasagi, M. Lang, Z.Q. Penfei, G. and Takewaki, I., (2014), "Optimal Placement and design of nonlinear dampers for building structures in the frequency domain", Earthq. Struct., 7(6), 1025-1044. https://doi.org/10.12989/eas.2014.7.6.1025
  12. He, W.L. and Agrawal, A.K. (2008), "Analytical model of ground motion pulses for the design and assessment of seismic protective systems", J. Struct. Eng., ASCE, 134(7), 1177-1188. https://doi.org/10.1061/(ASCE)0733-9445(2008)134:7(1177)
  13. Heidari, A., Rahgozar, R. and Kamgar, R. (2014), "Free vibration analysis of tall building with geometrical discontinuities", Acia. J. Civil. Eng., 15(1), 107-122.
  14. Herath, N., Haritos, N., Ngo, T. and Mendis, P. (2009), "Behavior of outrigger beams in high-rise buildings under earthquake loads, Aust. Earthq. Eng. Soc., Australia.
  15. Jahanshahi, M.R., Rahgozar, R. and Malekinejad, M. (2012), "A simple approach to static analysis of tall buildings with a combined tube-in-tube and outrigger-belt truss system subjected to lateral loading", Int. J. Eng. Trans. A: Basic., 25(3), 289-299.
  16. Jahanshahi, M.R. and Rahgozar, R. (2013), "Optimum location of outrigger-belt truss in tall buildings based on maximization of the belt truss strain energy", Int. J. Eng. Trans. A: Basics., 26(7), 693-700.
  17. Kalkan, E. and Kunnath, S.K. (2006), "Effects of fling step and forward directivity on seismic response of buildings", J. Earthq. Spectra., 22(2), 367-390. https://doi.org/10.1193/1.2192560
  18. Kamgar, R. and Rahgozar, R. (2013), "A simple approximate method for free vibration analysis of framed tube structures", Struct. Des. Tall. Spec., 22(2), 217-234. https://doi.org/10.1002/tal.680
  19. Kamgar, R. and Saadatpour, M.M. (2012), "A simple mathematical model for free vibration analysis of combined system consisting of framed tube, shear core, belt truss and outrigger system with geometrical discontinuities", Appl. Math. Model., 36(10), 4918-4930. https://doi.org/10.1016/j.apm.2011.12.029
  20. Kuang, J.S. and Ng, S.C. (2004), "Coupled vibration of tall buildings structures", Struct. Des. Tall. Spec., 13(4), 291-303. https://doi.org/10.1002/tal.253
  21. Malekinejad, M. and Rahgozar, R. (2014), "An analytical model for dynamic response analysis of tubular tall buildings", Struct. Des. Tall. Spec., 23(1), 67-80. https://doi.org/10.1002/tal.1039
  22. Moustafa, A. (2009), "Critical earthquake load inputs for multi-degree-of-freedom inelastic structures", J. Sound. Vib., 325(3), 532-544 https://doi.org/10.1016/j.jsv.2009.03.022
  23. Moustafa, A. (2011), "Damage-based design earthquake loads for single-degree-of-freedom inelastic structures", J. Struct. Eng., ASCE., 137(3), 456-467. https://doi.org/10.1061/(ASCE)ST.1943-541X.0000074
  24. Moustafa, A. (2012), Earthquake-Resistant Structures: Design, Assessment and Rehabilitation, InTech, Croatia, Italy.
  25. Rahgozar, R. and Sharifi, Y. (2009), "An approximate analysis of combined system of framed tube, shear core and belt truss in high-rise buildings", J. Struct. Des. Tall. Spec., 18(6), 607-624. https://doi.org/10.1002/tal.503
  26. Rahgozar, R., Mahmoudzadeh, Z., Malekinejad, M. and Rahgozar, P. (2014), "Dynamic analysis of combined system of framed tube and shear walls by Galerkin method using B-spline functions", J. Struct. Des. Tall. Spec., doi: 10.1002/tal.1201.
  27. Raj Kiran Nanduri, P.M.B., Suresh, B. and Ihtesham Hussain, M.D. (2013), "Optimum position of outrigger system for high-rise reinforced concrete buildings under wind and earthquake loadings", Am. J. Eng. Res., 2(8), 76-89.
  28. SeismoSignal 5.1.0 2013, Seismosoft Ltd., Pavia, Italy.
  29. Shinozuka, M. (1970), "Maximum structural response to seismic excitations", J. Eng. Mech., ASCE, 96(5), 729-738.
  30. Shinozuka, M. and Sato, Y. (1967), "Simulation of nonstationary random process", J. Eng. Mech., ASCE, 93(1), 11-40.
  31. Singh, J.P. (1984), "Characteristics of near-field ground motion and their importance in building design, ATC-10-1 Critical aspects of earthquake ground motion and building damage potential", ATC, 23-42.
  32. Stafford Smith, B. and Coull, A. (1991), Tall Building Structures: Analysis and Design, John Willey, New York, USA.
  33. Stein, R.S. (2003), "Earthquake conversations", Sci. Am., 288(1), 72-79. https://doi.org/10.1038/scientificamerican0103-72
  34. Swaddiwudhipong, S., Soelarno Sidji, S. and Lee, S.L. (2002), "The effects of axial deformation and axial force on vibration characteristics of tall buildings", J. Struct. Des. Tall. Spec., 11(5), 309-328. https://doi.org/10.1002/tal.203
  35. Takewaki, I. (2001a), "A new method for non-stationary random critical excitation", Earthq. Eng. Struct. Dyn., 30(4), 519-535. https://doi.org/10.1002/eqe.21
  36. Takewaki, I. (2001b), "Nonstationary random critical excitation for acceleration response", J. Eng. Mech., ASCE, 127(6), 544-556. https://doi.org/10.1061/(ASCE)0733-9399(2001)127:6(544)
  37. Takewaki, I. (2002), "Seismic critical excitation method for robust design: A review", J. Struct. Eng., ASCE, 128(5), 665-672. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:5(665)
  38. Takewaki, I., (2005), "Bound of earthquake input energy to soil-structure interaction systems", Soil. Dyn. Earthq. Eng., 25(7-10), 741-752. https://doi.org/10.1016/j.soildyn.2004.11.017
  39. Takewaki, I. (2013), Critical Excitation Methods in Earthquake Engineering, Elsevier, Netherlands.
  40. Takewaki, I., Moustafa, A. and Fujita, K. (2013), Improving the Earthquake Resilience of Buildings, the Worst Case Approach, Springer, London.
  41. Takewaki, I. (2013), "Toward greater building earthquake resilience using concept of critical excitation: A review", J. Sustain. City. Soc., 9, 39-53. https://doi.org/10.1016/j.scs.2013.02.001
  42. Taranath, B.S. (2012), Structural Analysis and Design of Tall Buildings: Steel and Composite Construction, Taylor & Francis, CRC Press, New York, USA.
  43. Trifunac, M.D. and Brady, A.G. (1975), "A study on the duration of strong earthquake ground motion", Bull. Seismol. Soc. Am., 65(3), 581-626.
  44. Uniform Building Code (1997), International Conference of Building Officials, Whittier, California, USA.
  45. Westermo, B.D. (1985), "The critical excitation and response of simple dynamic systems", J. Sound Vib., 100(2), 233-242. https://doi.org/10.1016/0022-460X(85)90417-1
  46. Wu, J.R. and Li, Q.S. (2003), "Structural performance of multi-outrigger braced tall buildings", J. Struct. Des. Tall. Spec., 12(2), 155-176. https://doi.org/10.1002/tal.219

피인용 문헌

  1. Optimal design of tuned mass dampers subjected to continuous stationary critical excitation 2018, https://doi.org/10.1007/s40435-017-0386-7
  2. Optimizing parameters of tuned mass damper subjected to critical earthquake vol.27, pp.7, 2018, https://doi.org/10.1002/tal.1460
  3. Generation of synthetic accelerograms using a probabilistic critical excitation method based on energy constraint vol.18, pp.1, 2015, https://doi.org/10.12989/eas.2020.18.1.045
  4. Analytical and Experimental Modal Analysis of Electrical Transmission Tower to Study the Dynamic Characteristics and Behaviors vol.24, pp.3, 2015, https://doi.org/10.1007/s12205-020-1563-3
  5. Numerical study of the seismic behavior of steel frame-tube structures with bolted web-connected replaceable shear links vol.35, pp.3, 2020, https://doi.org/10.12989/scs.2020.35.3.305
  6. Improvement of Performance Level of Steel Moment-Resisting Frames Using Tuned Mass Damper System vol.10, pp.10, 2015, https://doi.org/10.3390/app10103403
  7. Seismic performance of high-strength steel framed-tube structures with bolted web-connected replaceable shear links vol.37, pp.3, 2015, https://doi.org/10.12989/scs.2020.37.3.323
  8. Seismic Performance of Outrigger-Braced System Based on Finite Element and Component-Mode Synthesis Methods vol.44, pp.4, 2015, https://doi.org/10.1007/s40996-019-00299-3
  9. Energy dissipation characteristics of retrofitted damaged low-strength concrete bridge pier vol.174, pp.2, 2015, https://doi.org/10.1680/jbren.20.00016
  10. Application of discrete wavelet transform in seismic nonlinear analysis of soil-structure interaction problems vol.37, pp.3, 2021, https://doi.org/10.1177/8755293020988027
  11. Influence of rotation speed on motion accuracy of hydrostatic journal bearing vol.105, pp.4, 2015, https://doi.org/10.1007/s11071-021-06781-w