Elastomers and Composites

  • 제50권3호
  • /
  • Pages.184-188
  • /
  • 2015
  • /
  • 2092-9676(pISSN)
  • /
  • 2288-7725(eISSN)
한국고무학회 (The Rubber Society of Korea)
권호 표지
DOI QR코드

DOI QR Code

Processability and Mechanical Characteristics of Glass Fiber and Carbon Fiber Reinforced PA6 for Reinforcement Content

  • Lee, S.B. (Department of Product Design Manufacturing Engineering, Graduate School of Seoul National University of Science and Technology) ;
  • Cho, H.S. (Department of Product Design Manufacturing Engineering, Graduate School of Seoul National University of Science and Technology) ;
  • Lyu, M.-Y. (Department of Mechanical System Design Engineering, Seoul National University of Science and Technology)
  • 투고 : 2015.08.07
  • 심사 : 2015.08.21
  • 발행 : 2015.09.30
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

There is a need for light weight and high stiffness characteristics in the building structure as well as aircraft and cars. So fiber reinforced plastic with the addition of reinforcing agent such as glass fiber, carbon fiber, aramid fiber is utilized in this regard. In this study, mechanical strength, flow property and part shrinkage of glass fiber and carbon fiber reinforced PA6 were examined according to reinforcement content such as 10%, 20%, and 30%, and reinforcement type. The mechanical property was measured by a tensile test with specimen fabricated by injection molding and the flow property was measured by spiral test. In addition, we measured the part shrinkage of fiber reinforced PA6 that affects part quality. As glass fiber content increases, mechanical property increased by 75.4 to 182%, and flow property decreased by 18.9 to 39.5%. And part shrinkage decreased by 52.9 to 60.8% in the flow direction, and decreased by 48.2 to 58.1% in the perpendicular to the flow direction. As carbon fiber content increases, mechanical property increased by 180 to 276%, flow property decreased by 26.8 to 42.8%, and part shrinkage decreased by 65.0 to 71.8% and 69.5 to 72.7% in the flow direction and the direction perpendicular to the flow respectively.

키워드

참고문헌

  1. S. N. Hwang, "Development Trends of Functional Composite Materials", KISTI, Tech. Trend Report (2003).
  2. M. Lee, J. H. Kim, S. R. Park, and M.-Y. Lyu, "A Study on the Warpage in Injection Molded Part for Various Part Designs and Non Reinforced Resins", Elast. Compos., 44, 373 (2009).
  3. D. M. Moon, T. G. Choi, and M.-Y. Lyu, "Prediction of Mechanical Property of Glass Fiber Reinforced Polycarbonate and Evalution of Warpage through Injection molding", Polymer(Korea), 38, 708 (2014).
  4. M.-Y. Lyu and T. G. Choi "Research Trends in Polymer Materials for Use in Lightweight Vehicles", Int. J. Precis. Eng. Manuf., 16, 213 (2015). https://doi.org/10.1007/s12541-015-0029-x
  5. J.-H. Mo and M.-Y. Lyu, "Investigation of the Part Shrinkage in Injection Molding for Glass Fiber Reinforced Thermoplastics", Trans. Mater. Process., 13, 515 (2004). https://doi.org/10.5228/KSPP.2004.13.6.515
  6. Y. S. Kim and I. K. Kim, "Effect of Glass Fiber Contents on the tensile Strength in Injection Molding Process", J. Korean Soc. Prec. Eng., 17, 63 (2000).
  7. M. Lee, H. Kim, and M.-Y. Lyu, "A Study on Warpage of Glass Fiber Reinforced Plastics for Part Design and Operation Condition: Part 1. Amorphous Plastics", Polymer(Korea), 36, 555 (2012).
  8. M. Lee, H. Kim, and M.-Y. Lyu, "A Study on Warpage of Glass Fiber Reinforced Plastics for Part Design and Operation Condition: Part 2. Crystalline Plastics", Polymer(Korea), 36, 677 (2012).
  9. W. C. Jung, Y. M. Heo, K. H. Shin, G. S. Yoon, S. H. Chang, and M. Y. Kim, "An Experimental Study on Molding Factor for Spiral Type Micro injection Product", Trans. Mater. Process., 15, 65 (2006). https://doi.org/10.5228/KSPP.2006.15.1.065
  10. ASTM D 638-10 "Standard Test Method for Tensile Properties of Plastics", ASTM Annual Book (2010).
  11. ASTM D 3123-98 "Standard Test Method for Spiral Flow of Low-Pressure Thermosetting Molding Compounds", ASTM Annual Book (1998).
  12. ASTM D 955-00 "Standard Test Method of Measuring Shrinkage from Mold Dimensions of Thermoplastics", ASTM Annual Book (2000).
  13. M. A. Lee and M.-Y. Lyu, "A Study on the Part Shrinkage in Injection Molded Annular Shaped Product for Glass Reinforced Polycarbonate", Elast. Compos., 48, 300 (2013). https://doi.org/10.7473/EC.2013.48.4.300
  14. S. T. Won, T. B. Kim, S. Lee, J. M. Won, K. H. Cha, and M.-Y. Lyu, "A Study on the Stress Measurement in a Plastic Product using Chemical Cracking Method", Elast. Compos., 47, 336 (2012). https://doi.org/10.7473/EC.2012.47.4.336
  15. M. A. Lee and M.-Y. Lyu, " A Study on the part Shrinkage in Injection Molded Annular Shaped Product for Glass Reinforced Polycarbonate", Elast. Compos., 48, 300 (2013). https://doi.org/10.7473/EC.2013.48.4.300