Geomechanics and Engineering

  • 제9권2호
  • /
  • Pages.219-241
  • /
  • 2015
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Application of waste rubber to reduce the settlement of road embankment

  • Tafreshi, S.N. Moghaddas (Department of Civil Engineering, K.N. Toosi University of Technology) ;
  • Norouzi, A.H. (Department of Civil, Construction and Environmental Engineering, North Carolina State University)
  • 투고 : 2014.10.01
  • 심사 : 2015.04.09
  • 발행 : 2015.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

In this paper, a series of repeated load tests were carried out on a 150 mm diameter plate simulative of vehicle passes, to demonstrate the benefits of soil-rubber shred mixture in decreasing the soil surface settlement of road embankment. The results show that the efficiency of rubber reinforcement is significantly a function of the rubber content, thickness of rubber-soil mixture and soil cap thickness over the mixture. Minimum surface settlement is provided by 2.5% of rubber in rubber-soil mixture, the thickness of mixture layer and soil cap of 0.5 times the loading surface diameter, giving values of 0.32-0.68 times those obtained in the unreinforced system for low and high values of amplitude of repeated load. In this installation, in contrast with unreinforced bed that shows unstable response, the rate of enhancement in settlement decreases significantly as the number of loading cycles increase and system behaves resiliently without undergoing plastic deformation. The findings encourage the use of rubber shreds obtained from non-reusable tires as a viable material in road works.

키워드

참고문헌

  1. AASHTO T 221-90 (2012), Repetitive static plate load tests of soils and flexible pavement components for use in evaluation and design of airport and highway pavements.
  2. Arabani, M., Moghadas Nejad, F. and Azarhoosh, A.R. (2013), "Laboratory evaluation of recycled waste concrete into asphalt mixtures", Int. J. Pav. Eng., 14(6), 531-539. https://doi.org/10.1080/10298436.2012.747685
  3. Arabani, M., Mirabdolazimi, S.M. and Sasani, A.R. (2010), "The effect of waste tire thread mesh on the dynamic behaviour of asphalt mixtures", Constr. Build. Mater., 24(6),1060-1068. https://doi.org/10.1016/j.conbuildmat.2009.11.011
  4. ASTM D1195 (2009), Standard Test Method for Repetitive Static Plate Load Tests of Soils and Flexible Pavement Components for Use in Evaluation and Design of Airport and Highway Pavements; ASTM International, West Conshohocken, PA, USA.
  5. ASTM D2487 (2003), Standard Practice for Classification of Soils for Engineering Purposes, Unified Soil Classification System, ASTM International, West Conshohocken, PA, USA.
  6. Bosscher, P.J., Edil, T.B. and Kuraoka, S. (1997), "Design of highway embankments using tire chips", J. Geotech. Geoenviron. Eng. - ASCE, 123(4), 295-304. https://doi.org/10.1061/(ASCE)1090-0241(1997)123:4(295)
  7. Brito, L.A.T. and Dawson, A.R. (2007), "Roads under timber traffic. Nottingham transportation engineering centre", NTEC report No. 07016, University of Nottingham, England.
  8. Cao, W. (2007), "Study on properties of recycled tire rubber modified asphalt mixtures using dry process", Constr. Build. Mater., 21(5), 1011-1015. https://doi.org/10.1016/j.conbuildmat.2006.02.004
  9. Celauro, B., Celauro, C., Presti, D.L. and Bevilacqua, A. (2012), "Definition of a laboratory optimization protocol for road bitumen improved with recycled tire rubber", Constr. Build. Mater., 37, 562-572. https://doi.org/10.1016/j.conbuildmat.2012.07.034
  10. Cetin, H., Fener, M. and Gunaydin, O. (2006), "Geotechnical properties of tire-cohesive clayey soil mixtures as a fill material", Eng. Geol., 88(1-2), 110-120. https://doi.org/10.1016/j.enggeo.2006.09.002
  11. Cetin, B., Aydilek, A.H. and Li, L. (2012), "Experimental and numerical analysis of metal leaching from fly ash-amended highway bases", Waste. Manage., 32(5), 965-978. https://doi.org/10.1016/j.wasman.2011.12.012
  12. Chiu, C.T. (2008), "Use of ground tire rubber in asphalt pavements: field trial and evaluation in Taiwan", J. Res. Conserv. Recy., 52(3), 522-532. https://doi.org/10.1016/j.resconrec.2007.06.006
  13. Collins, K.J., Jensen, A.C., Mallinson, J.J., Roenelle, V. and Smith, I.P. (2002), "Environmental impact assessment of a scrap tyre artificial reef", J. Mar. Sci. Technol., 59, 243-249.
  14. Edil, T. and Bosscher, P. (1994), "Engineering properties of tire chips and soil mixtures", Geotech. Test. J., 17(4), 453-464. https://doi.org/10.1520/GTJ10306J
  15. Edincliler, A., Baykal, G. and Dengili, K. (2004), "Determination of static and dynamic behavior of recycled materials for highways", Resour. Constr. Recy., 42(3), 223-237. https://doi.org/10.1016/j.resconrec.2004.04.003
  16. Edincliler, A., Baykal, G. and Saygili., A. (2010), "Influence of different processing techniques on the mechanical properties of used tires in embankment construction", Waste. Manage., 30(6), 1073-1080. https://doi.org/10.1016/j.wasman.2009.09.031
  17. Edincliler, A. and Cagatay, A. (2013), "Weak subgrade improvement with rubber fibre inclusions", Geosynth. Int., 20(1), 39-46. https://doi.org/10.1680/gein.12.00038
  18. Fang, Y., Zhan, M. and Wang, Y. (2001), "The status of recycling of waste rubber", Mater. Design., 22(2), 123-127. https://doi.org/10.1016/S0261-3069(00)00052-2
  19. Feng, Z.Y. and Sutter, K.G. (2000), "Dynamic properties of granulated rubber sand mixtures", Geotech. Test. J., 23(3), 338-344. https://doi.org/10.1520/GTJ11055J
  20. Fontes, L.P.T.L., Triches, G., Pais, J.C. and Pereira, P.A.A. (2010), "Evaluating permanent deformation in asphalt rubber mixtures", Constr. Build. Mater., 24(7), 1193-1200. https://doi.org/10.1016/j.conbuildmat.2009.12.021
  21. Hataf, N. and Rahimi, M.M. (2005), "Experimental investigation of bearing capacity of sand reinforced with randomly distributed tire shreds", Constr. Build. Mater., 20(10), 910-916. https://doi.org/10.1016/j.conbuildmat.2005.06.019
  22. Hsieh, C. and Mao, L. (2005), "A bench-scale performance test for evaluation of the geosynthetic reinforcement effects on granular base courses", GRI-18 Geosynthetics Research and Development in Progress, Geofrontiers, Austin, TX, USA.
  23. Karabash, Z. and Cabalar, A.F. (2015), "Effect of tire crumb and cement addition on triaxial shear behavior of sandy soils", Geomech. Eng., Int. J., 8(1), 1-15. https://doi.org/10.12989/gae.2015.8.1.001
  24. Keskin, M.S. and Laman, M. (2014), "Experimental study of bearing capacity of strip footing on sand slope reinforced with tire chips", Geomech. Eng., Int. J., 6(3), 249-262. https://doi.org/10.12989/gae.2014.6.3.249
  25. Kim, I.T. and Tutumluer, E. (2005), "Unbound aggregate rutting models for stress rotations and effects of moving wheel loads", Transportation Research Record; J. Transport. Res. Board , 1913, 41-49. https://doi.org/10.3141/1913-05
  26. Lazizi, A., Trouzine, H., Asroun, A. and Belabdelouahab, F. (2014), "Numerical simulation of tire reinforced sand behind retaining wall under earthquake excitation", Eng. Technol. Appl. Sci. Res., 4(2), 605-614.
  27. Lee, J., Dodds, J. and Santamarina, J.C. (2007), "Behavior of Rigid-Soft Particle Mixtures", J. Mater. Civil. Eng. - ASCE, 19(2), 179-184. https://doi.org/10.1061/(ASCE)0899-1561(2007)19:2(179)
  28. Mishra, H.K. and Igarashi, A. (2013), "Lateral deformation capacity and stability of layer-bonded scrap tire rubber pad isolators under combined compressive and shear loading", Struct. Eng. Mech., Int. J., 48(4), 479-500. https://doi.org/10.12989/sem.2013.48.4.479
  29. Moghaddas Tafreshi, S.N. and Dawson, A.R. (2010), "Behaviour of footings on reinforced sand subjected to repeated loading-comparing use of 3D and planar geotextile", Geotext. Geomembr., 28(5), 434- 447. https://doi.org/10.1016/j.geotexmem.2009.12.007
  30. Moghaddas Tafreshi, S.N. and Norouzi, A.H. (2012), "Bearing capacity of a square model footing on sand reinforced with shredded tire-an experimental investigation", Constr. Build. Mater., 35, 547-556. https://doi.org/10.1016/j.conbuildmat.2012.04.092
  31. Moghaddas Tafreshi, S.N., Khalaj, O. and Dawson, A.R. (2014), "Repeated loading of soil containing granulated rubber and multiple geocell layers", Geotext. Geomembr., 42(1), 25-38. https://doi.org/10.1016/j.geotexmem.2013.12.003
  32. Prasad, D.S.V. and Prasada Raju, G.V.R. (2009), "Performance of waste tyre rubber on model flexible pavement", ARPN. J. Eng. Appl. Sci., 4(6), 89-92.
  33. Recycling Research Institute (2009), Online available from: http://www.scraptirenews.com (Accessed on 30 May, 2011).
  34. Rubber Manufacturers Association (2007), Online available from: http://www.rma.org (Accessed on 30 May, 2011).
  35. Sellaf, H., Trouzine, H., Hamhami, M. and Asroun, A. (2014), "Geotechnical properties of rubber tires and sediments mixtures", Eng. Technol. Appl. Sci. Res., 4(2), 618-624.
  36. Smith, C.C., Anderson, W.F. and Freewood, R.J. (2001), "Evaluation of shredded tyre chips as sorption media for passive treatment walls", Eng. Geol., 60(1-4), 253-261. https://doi.org/10.1016/S0013-7952(00)00106-X
  37. Tavakoli Mehrjardi, Gh., Moghaddas Tafreshi, S.N. and Dawson, A.R. (2012), "Combined use of geocell reinforcement and rubber-soil mixtures to improve performance of buried pipes", Geotext. Geomembr., 34, 116-130. https://doi.org/10.1016/j.geotexmem.2012.05.004
  38. Upton, R. and Machan, G. (1993), "Use of shredded tires for lightweight fill", Transport. Res. Rec., 1422, 36-45.
  39. Wang, H., You, Z., Mills-Beale, J. and Hao, P. (2012), "Laboratory evaluation on high temperature viscosity and low temperature stiffness of asphalt binder with high percent scrap tire rubber", Constr. Build. Mater., 26(1), 583-590. https://doi.org/10.1016/j.conbuildmat.2011.06.061
  40. Warith, M.A. and Rao, S.M. (2006), "Predicting the compressibility behaviour of tire shred samples for landfill applications", Waste. Manage., 26(3), 268-276. https://doi.org/10.1016/j.wasman.2005.04.011
  41. Waste and Resources Action Programme (2005), "Tyres re-use and recycling", Online available from http://www.wrap.org.uk (Accessed on 30 May, 2011).
  42. Weissman, S.L. (1999), "Influence of Tire-Pavement Contact Stress Distribution on Development of Distress Mechanisms in Pavements", Transport. Res. Rec., 1655, 161-167. https://doi.org/10.3141/1655-21
  43. Wu, J.Y. and Tsai, M. (2009), "Feasibility study of a soil-based rubberized CLSM", Waste. Manage., 29(2), 636-642. https://doi.org/10.1016/j.wasman.2008.06.017
  44. Yang, Z. (1974), "Strength and Deformation Characteristics of Reinforced Sand", Ph.D. Thesis.
  45. Yoon, S., Prezzi, M., Siddiki, N.Z. and Kim, B. (2006), "Construction of a test embankment using a sand-tire shred mixture as fill material", Waste. Manage., 26(9), 1033-1044. https://doi.org/10.1016/j.wasman.2005.10.009
  46. Yoon, Y.W., Heo, S.B. and Kim, S.K. (2008), "Geotechnical performance of waste tires for soil reinforcement from chamber tests", Geotext. Geomembr., 26(1), 100-107. https://doi.org/10.1016/j.geotexmem.2006.10.004

피인용 문헌

  1. Experimental and numerical investigation of footing behaviour on multi-layered rubber-reinforced soil 2016, https://doi.org/10.1080/19648189.2016.1262288
  2. Settlement behavior and controlling effectiveness of two types of rigid pile structure embankments in high-speed railways vol.11, pp.6, 2016, https://doi.org/10.12989/gae.2016.11.6.847
  3. Potential use of waste rubber shreds in drainage layer of landfills - An experimental study vol.5, pp.3, 2016, https://doi.org/10.12989/aer.2016.5.3.201
  4. Mechanical properties of expanded polystyrene beads stabilized lightweight soil vol.13, pp.3, 2015, https://doi.org/10.12989/gae.2017.13.3.459
  5. Traffic-load-induced dynamic stress accumulation in subgrade and subsoil using small scale model tests vol.16, pp.2, 2018, https://doi.org/10.12989/gae.2018.16.2.113
  6. Evaluation of extension in service life and layer thickness reduction of stabilized flexible pavement vol.3, pp.2, 2018, https://doi.org/10.12989/acd.2018.3.2.201
  7. Comparison of behaviour of basal reinforced piled embankment with two layer of reinforcement vol.16, pp.3, 2015, https://doi.org/10.12989/gae.2018.16.3.233
  8. Damping Ratio of Foundation Bed with Multi-layered Rubber-Soil Mixtures vol.221, pp.None, 2015, https://doi.org/10.1088/1755-1315/221/1/012008
  9. Strength and deformation behaviour of sand-rubber mixture vol.15, pp.9, 2015, https://doi.org/10.1080/19386362.2020.1812193