Structural Engineering and Mechanics

  • 제55권4호
  • /
  • Pages.765-784
  • /
  • 2015
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Standardization of composite connections for trapezoid web profiled steel sections

  • Saggaff, A. (Civil Engineering Department, Faculty of Engineering, Sriwijaya University) ;
  • Tahir, M.M. (UTM Construction Research Centre, Institute for Smart Infrastructure and Innovative Construction (IISIC), Faculty of Civil Engineering, Universiti Teknologi Malaysia (UTM)) ;
  • Sulaiman, A. (UTM Construction Research Centre, Institute for Smart Infrastructure and Innovative Construction (IISIC), Faculty of Civil Engineering, Universiti Teknologi Malaysia (UTM)) ;
  • Ngian, S.P. (UTM Construction Research Centre, Institute for Smart Infrastructure and Innovative Construction (IISIC), Faculty of Civil Engineering, Universiti Teknologi Malaysia (UTM)) ;
  • Mirza, J. (UTM Construction Research Centre, Institute for Smart Infrastructure and Innovative Construction (IISIC), Faculty of Civil Engineering, Universiti Teknologi Malaysia (UTM))
  • 투고 : 2013.06.06
  • 심사 : 2015.07.14
  • 발행 : 2015.08.25
⟨ 이전 논문 다음 논문 ⟩

초록

Connections are usually designed either as pinned usually associated with simple construction or rigid normally is associated with continuous construction. However, the actual behaviour falls in between these two extreme cases. The use of partial strength or semi-rigid connections has been encouraged by Euro-code 3 and studies on semi-continuous construction have shown substantial savings in steel weight of the overall construction. Composite connections are proposed in this paper as partial or full strength connections. Standardized connection tables are developed based on checking on all possible failure modes as suggested by "component method" for beam-to-column composite connection on major axis. Four experimental tests were carried out to validate the proposed standardised connection table. The test results showed good agreement between experimental and theoretical values with the ratio in the range between 1.06 to 1.50. All tested specimens of the composite connections showed ductile type of failure with the formation of cracks occurred on concrete slab at maximum load. No failure occurred on the Trapezoidal Web Profiled Steel Section as beam and on the British Section as column.

키워드

참고문헌

  1. Bose, B. (1993), "Tests to verify the performance of standard ductile connections", Dundee Institute of Technology.
  2. British Standards Institute BS 5950-1 (2000), Structural Use of Steelwork in Building Part 1: Code of Practice for Design . Rolled and Welded Sections, British Standards Institution, London
  3. British Standards Institute BS 5950 Part 3, Section 3.1 (1990), Design of simple and continuous composite beams, BSI, London.
  4. British Standards Institution BS 8110 (1997), Structural use of concrete. Part 1: Code of practice for design and construction, BSI, London.
  5. Chen, W. F. and Kishi, N. (1989), "Semi-rigid steel beam-to-column connections: database and modelling", J. Struct. Eng., 115(1), 105-119. https://doi.org/10.1061/(ASCE)0733-9445(1989)115:1(105)
  6. Couchman, G.H. (1997), Design of Semi-continuous Braced Frames, Steel Construction Institute Publication 183, Silwood Park, Ascot, Berkshire SL5 7QN, U.K
  7. Eurocode 3: BS EN 1993-1-1 (2005), Eurocode 3, Design of Steel Structures - Part 1-1: General Rules and Rules for Buildings, CEN, Brussels.
  8. Eurocode 3: BS EN 1993-1-8 (2005), Eurocode 3, Design of Steel Structures - Part 1-8:Design of Joints, CEN, Brussels.
  9. Eurocode 3: BS EN 1993-1-5 (2005), Eurocode 3, Design of steel structures Part 1-5: Plated structural elements, CEN Brussels
  10. Eurocode 4, (1994), Eurocode 4: Design of composite steel and concrete structures, Part 1.1 General rules and rules for buildings, CEN, Brussels.
  11. European Commission (EC), COST C1 (1996), Semi-rigid behaviour of civil engineering structural connections, composite steel-concrete joints in braced steel frames for buildings, EC.
  12. Habashizadeh, A.M., Chenaglou, M.R., Abedi, K. and Afshin, H. (2013), "3D finite element modelling of composite connection of RCS frame subjected to cyclic loading", Steel Compos. Struct., 15(3), 281-298. https://doi.org/10.12989/scs.2013.15.3.281
  13. Hussein, W.Q. (2001), Design Guide for Steel Plate Girder with Corrugated Webs (TWP), Presentation in Design of Steel Structure Short Course, TWP Sdn Bhd.
  14. Jaspart, J.P. (2000), "General report: session on connections", J. Construct. Steel Res., 55, 69-89. https://doi.org/10.1016/S0143-974X(99)00078-4
  15. Johnson, R. and Caffola, J. (1997), "Local flange buckling in plate girders with corrugated webs", Proceeding Inst. Civil Engineers, Structures and Buildings, 148-156.
  16. Lawson, R.M. (1990), Commentary on BS 5950:Part 3: Section 3.1, Steel Construction Institute P078, 'Composite Beam', Silwood Park, Ascot, Berks SL 7QN, London.
  17. Luo, R. (1995), "Load carrying capacity of steel girders and panels with thin-walled trapezoidally corrugated webs", Compilation of Papers, Chalmers University of Technology, Sweden.
  18. Osman, M.H. (2001), "Performance test and research on trapezoid web profile", Presentation in Design of Steel Structure Short Course, Universiti Teknologi Malaysia.
  19. Saggaff, A. (2007), "Behaviour of composite partial strength connections with built-up steel sections", PhD Thesis, Universiti Teknologi Malaysia, Skudai, Johor, Malaysia.
  20. Sayed, A.E.Y (2007), "Design aspects of steel I-girders with corrugated steel webs", Elec. J. Struct. Eng., 7, 27-40.
  21. Shi, W.L., Li, G.Q., Ye, Z.M. and Xiao, R.Y. (2007), "Cyclic loading tests on composite joints with flush end plate connections", Int. J. Steel Struct., 7, 119-128. https://doi.org/10.12989/scs.2007.7.2.119
  22. Steel Construction Institute and British Constructional Steelwork Association, SCI P213 (1998), Joints in Steel Construction Composite Connections, Silwood Park, Ascot, Berks SL 7QN, London.
  23. Steel Construction Institute and British Constructional Steelwork Association, SCI P207 (1996), Joints in Steel Construction. Moment Connections, Silwood Park, Ascot, Berks SL 7QN, London.
  24. Steel Construction Institute and British Constructional Steelwork Association, SCI P212 (2009), Joints in Steel Construction, Simple Constructions, Silwood Park, Ascot, Berks SL 7QN, London.
  25. Steel Insight (2012), "Cost planning through design stages", Chris.dolling @ steelconstruction.org.
  26. Sulaiman, A. (2007), "Behaviour of partial strength connections with trapezoid web profiled steel sections", Ph.D Thesis, Universiti Teknologi Malaysia, Skudai, Johor, Malaysia.
  27. Tahir, M.M. (1995), "Structural and economic aspects of the use of semi-rigid joints in steel frames", PhD Thesis, University of Warwick, United Kingdom.
  28. Tahir, M.M., Sulaiman, A. and Saggaff, A. (2008), "Structural behaviour of trapezoidal web profiled steel beam section using partial strength connection", Elec. J. Struct. Eng., 8, 55-66.
  29. Tahir, M.M., Hussein, M.A., Sulaiman, A. and Mohammad, S. (2009), "Comparison of component method with experimental tests for flush end-plate connections using hot-rolled perwaja steel sections", Int. J. Steel Struct., Korean Soc. Steel Constr., 9(2), 161-174. https://doi.org/10.1007/BF03249491
  30. Tahir, M.M. and Sulaiman, A. (2008), "Experimental tests on extended end-plate connection with variable parameters", Int. J. Steel Struct., Korean Soc. Steel Constr., 8(4), 369-381.