Journal of the Korean Solar Energy Society (한국태양에너지학회 논문집)

The Korean Solar Energy Society (한국태양에너지학회)
권호 표지
DOI QR코드

DOI QR Code

Predicted Cooling Performance of Single Finned Heat Dissipating Block for Economic Assessment of LED Module Markings in Standards

LED 모듈 표준 표시사항의 경제적인 평가를 위한 단일 핀 방열 블록의 냉각성능 예측

  • Huh, Young-Joon (Department of New & Renewable Energy Engineering, Dongguk University) ;
  • Song, Myung-Ho (Department of Mechanical, Robotics and Energy Engineering, Dongguk University)
  • 허영준 (동국대학교 신재생에너지공학과) ;
  • 송명호 (동국대학교 기계로봇에너지공학과)
  • Received : 2015.06.18
  • Accepted : 2015.06.29
  • Published : 2015.06.30
Download PDF
⟨ Previous Next ⟩

Abstract

LED has received intensive research attention due to its long life, high efficacy, fast response and wide colour availability, and has secured extensive application areas. However, LED chips within the modules convert only fraction of electric energy into light, and majority of supplied energy needs to be dissipated as heat, which challenges in the performance and life of the LED modules. IEC 62717 specifies the performance requirements for LED modules together with the test methods and conditions. The present study examined the influence of different design parameters on performance temperature through series of experiments and numerical simulations. The economic means to change the module performance temperature during the measurement of mandatory markings were suggested based on predicted cooling performances.

Keywords

References

  1. Park. J. W, Rapid thermal diffusion devices development of the high power LED lighting system, Proceedings of Korea society of precision engineering autumn conference, pp. 593-594, 2010.
  2. N. Narendran, Y. Gu, Life of LED-based white light sources, IEEE/OSA Journal of Display Technology, September, pp. 167-171, 2005.
  3. Shin. M. H, The present status of high power LED packaging technology, Physics & high technology, November, pp. 16-21, 2008.
  4. S. Keeping, Understanding the cause of fading in high-brightness LEDs, http://www.digikey.com/en/articles/techzone/2012/feb/understandingthe-cause-of-fading-in-high-brightness-leds, 2012.
  5. Y. Tang, X. Ding, B. Yu, Z. Li, B. Liu, A high power LED device with chips directly mounted on heat pipes, Applied Thermal Engineering 66, pp. 632-639, 2014. https://doi.org/10.1016/j.applthermaleng.2014.02.067
  6. Kim. L, Choi. J. H, Jang. S. H and Shin. M. W, Thermal analysis of LED array system with heat pipe, Thermochimica Acta 455, pp. 21-25, 2007. https://doi.org/10.1016/j.tca.2006.11.031
  7. Hwang. S. H, Park. S. J, Lee. Y. L, A study of optimal design for a 10W LED lamp, KAIS, Vol. 11, No. 7, pp. 2317-2322, 2010.
  8. Kim. C. M, Jung. C. W, Kang. Y. T, Study on the heat dissipation performance of LED by thermal conductivity enhanement of carbon nanogrease, Proceeding of the SAREK summer conference, pp. 105-108, 2013.
  9. H. Ye, M. Mihailovic, C. K. Y. Wong, H.W. van Zeijl, A. W. J. Gielen, G. Q. Zhang, P. M. Sarro, Two-phase cooling of light emitting diode for higher light output and increased efficiency, Applied Thermal Engineering, Vol. 52, pp. 353-359, 2013. https://doi.org/10.1016/j.applthermaleng.2012.12.015
  10. B. Siegal, Practical considerations in high power LED junction temperature measurements, Proceedings of International Electronic Manufacturing Technology, Putrajaya, Malaysia, pp. 62-66, 2006.
  11. Youk. J. H, Hong. D. W, Lee. S. J, Basic Design Guidelines for LED Lamp Packages, Korean Journal of Optics and Photonics, Vol. 22, No. 3, June, 2011.