Structural Engineering and Mechanics

  • 제54권6호
  • /
  • Pages.1267-1281
  • /
  • 2015
  • /
  • 1225-4568(pISSN)
  • /
  • 1598-6217(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Shear response of lean duplex stainless steel plate girders

  • Armoosh, Salam R. (Department of Civil and Structural Engineering, Universiti Kebangsaan Malaysia) ;
  • Khalim, A.R. (Department of Civil and Structural Engineering, Universiti Kebangsaan Malaysia) ;
  • Mahmood, Akram Sh. (Department of Civil Engineering, University of Al-Anbar)
  • 투고 : 2013.09.12
  • 심사 : 2015.05.15
  • 발행 : 2015.06.25
⟨ 이전 논문 다음 논문 ⟩

초록

Carbon steel plate girders have been used on a large scale in the building industry. Nowadays, Lean Duplex Stainless Steel (LDSS) plate girders are gaining popularity as they possess greater strength and are more impervious to corrosion than those that are constructed from carbon steel. Regardless of their popularity, there is very limited information with regards to their shear behavior. In this paper, the non-linear finite element analysis was employed to investigate the shear behavior of LDSS plate girders. Parameters considered were the web thickness, the flange width, and the girders aspect ratio. The analysis revealed that although the shear behavior of the LDSS girders was no different from that of carbon steel plate girders, it had obviously been affected by the non-linearity of the material. Furthermore, the selected parameters were found to pronounce effect on the shear capacity of the LDSS girders. That is, the shear capacity increased considerably with web thickness, and increased slightly with flange width. However, it was reduced as the aspect ratio increased. Comparisons between the finite element analysis failure loads and those predicted by the current European Code of Practice revealed that the latter underestimated the shear strength of the LDSS plate girders.

키워드

참고문헌

  1. EN 1993-1-4 (2006), Eurocode 3, Design of Steel Structures Part 1-4, General rules; Supplementary rules for stainless steel, CEN.
  2. EN 1993-1-5 (2007), Eurocode 3, Design of steel structures Part 1-5, Plated Structural Elements, CEN.
  3. ENV 1993-1-1 (1992), Eurocode 3, Design of steel structures Part 1-1, General rules and rules for buildings, CEN.
  4. ENV 1993-1-5 (1997), Eurocode 3, Design of steel structures Part 1-5, General rules; Supplementary rules for planar plated structures without transverse loading, CEN.
  5. Estrada, I., Real, E. and Mirambell, E. (2007a), "General behaviour and effect of rigid and non-rigidend post in stainless steel plate girders loaded in shear. part I: eperimental study", J. Construct. Steel Res., 63(7), 970-984. https://doi.org/10.1016/j.jcsr.2006.08.009
  6. Estrada, I., Real, E. and Mirambell, E. (2007b), "General behaviour and effect of rigid and non-rigidend post in stainless steel plate girders loaded in shear. part II: extended numerical study and design proposal", J. Construct. Steel Res., 63(7), 985-996. https://doi.org/10.1016/j.jcsr.2006.08.010
  7. LUSAS V14.3 (2006).
  8. Gardner, L. (2005), "The use of stainless steel in structures", Prog. Struct. Eng. Mater., 7(2), 45-55. https://doi.org/10.1002/pse.190
  9. Gunn, R.N. (1997), Duplex Stainless Steels: Microstructure, Properties and Applications, TWI Ltd, London, UK.
  10. Hassanein, M. (2010), "Imperfection analysis of austenitic stainless steel plate girders failing by shear", Eng. Struct., 32(3), 704-713. https://doi.org/10.1016/j.engstruct.2009.11.016
  11. Hassanein, M. (2011), "Finite element investigation of shear failure of lean duplex stainless steel plate girders", Thin Wall. Struct., 49(8), 964-973. https://doi.org/10.1016/j.tws.2011.03.009
  12. Hoglund, T. (1997), "Shear buckling resistance of steel and aluminum plate girders", Thin Wall. Struct., 29(1), 13-30. https://doi.org/10.1016/S0263-8231(97)00012-8
  13. Longshithung Patton, M. and Singh, K.D. (2012), "Numerical modelling of lean duplex stainless steel hollow columns of square, L-, T-, and+-shaped cross sections under pure axial compression", Thin Wall. Struct., 53, 1-8. https://doi.org/10.1016/j.tws.2012.01.002
  14. Osgood, W. and Ramberg, W. (1943), "Description of stress-strain curves by three parameters", Tech. Notes Nat. Adv. Comm. Aeronaut, 902(13), Document ID: 19930081614.
  15. Rasmussen, K.J. (2003), "Full-range stress-strain curves for stainless steel alloys", J. Construct. Steel Res., 59(1), 47-61. https://doi.org/10.1016/S0143-974X(02)00018-4
  16. Real, E., Mirambell, E. and Estrada, I. (2007), "Shear response of stainless steel plate girders", Eng. Struct., 29(7), 1626-1640. https://doi.org/10.1016/j.engstruct.2006.08.023
  17. Rockey, K.C. and Skaloud, M. (1972), "The ultimate load behaviour of plated girders loaded in shear", Struct. Eng., 50(1), 29-47.
  18. Saliba, N. and Gardner, L. (2013), "Experimental study of the shear response of lean duplex stainless steel plate girders", Eng. Struct., 46, 375-391. https://doi.org/10.1016/j.engstruct.2012.07.029
  19. Saliba, N. and Gardner, L. (2013), "Cross-section stability of lean duplex stainless steel welded I-sections", J. Construct. Steel Res., 80, 1-14. https://doi.org/10.1016/j.jcsr.2012.09.007
  20. Saliba, N., Real, E., Gardner, L. (2014), "Shear design recommendations for stainless steel plate girders", Eng. Struct., 59, 220-228. https://doi.org/10.1016/j.engstruct.2013.10.016
  21. Theofanous, M. and Gardner, L. (2010), "Experimental and numerical studies of lean duplex stainless steel beams", J. Construct. Steel Res., 66(6), 816-825. https://doi.org/10.1016/j.jcsr.2010.01.012
  22. Unosson, E. and Olsson, A. (2003), "Stainless steel girders-resistance to concentrated loads and shear", Proceedings of The Stainless Steel in Structures: International Experts Seminar, Ascot, UK, May.
  23. Wilson, J.M. (1886), "On specifications for strength of iron bridges", Tran. Am. Soc. Civil Eng., 15(1), 389-414.

피인용 문헌

  1. Ultimate Behaviour of Perforated Steel Plate Girders Subjected to Shear Loading vol.14, pp.None, 2015, https://doi.org/10.2174/1874836802014010070