Computers and Concrete

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Combined strain gradient and concrete strength effects on flexural strength and ductility design of RC columns

  • Chen, M.T. (Department of Civil Engineering, The University of Hong Kong) ;
  • Ho, J.C.M. (School of Civil Engineering, The University of Queensland)
  • Received : 2014.07.21
  • Accepted : 2014.11.15
  • Published : 2015.04.25
⟨ Previous Next ⟩

Abstract

The stress-strain relationship of concrete in flexure is one of the essential parameters in assessing the flexural strength and ductility of reinforced concrete (RC) columns. An overview of previous research studies revealed that the presence of strain gradient would affect the maximum concrete stress developed in flexure. However, no quantitative model was available to evaluate the strain gradient effect on concrete under flexure. Previously, the authors have conducted experimental studies to investigate the strain gradient effect on maximum concrete stress and respective strain and developed two strain-gradient-dependent factors k3 and ko for modifying the flexural concrete stress-strain curve. As a continued study, the authors herein will extend the investigation of strain gradient effects on flexural strength and ductility of RC columns to concrete strength up to 100 MPa by employing the strain-gradient-dependent concrete stress-strain curve using nonlinear moment-curvature analysis. It was evident from the results that both the flexural strength and ductility of RC columns are improved under strain gradient effect. Lastly, for practical engineering design purpose, a new equivalent rectangular concrete stress block incorporating the combined effects of strain gradient and concrete strength was proposed and validated. Design formulas and charts have also been presented for flexural strength and ductility of RC columns.

Keywords

Acknowledgement

Supported by : Hong Kong Special Administrative Region

References

  1. ACI Committee 318 (2008), Building code requirements for reinforced concrete and commentary, ACI 318M-08, Manual of Concrete Practice, American Concrete Institute, Michigan, USA, 465.
  2. Ahn, J., Lee, J., Bahn, B. and Shin, S. (2000), "An experimental study of the behaviour of high-strength reinforced concrete columns subjected to reversed cyclic shear under constant axial compression", Mag.Concrete Res., 52(3), 209-218. https://doi.org/10.1680/macr.2000.52.3.209
  3. Attard, M.M. and Setunge, S. (1996), "Stress-strain relationship of confined and unconfined concrete", ACI Mater. J., 93(5), 432-442.
  4. Azizinamini, A., Kuska, S.S.B., Brungardt, P. and Hatfield, E. (1994), "Seismic behavior of square highstrength concrete columns", ACI Struct. J., 91(3), 336-345.
  5. Basappa Setty, R. and Rangan, B. (1996), "Failure load of high strength concrete (hsc) columns under eccentric compression", Transact. Inst. Eng., Australia. Civil Eng., 38(1), 19-30.
  6. Bayrak, O. and Sheikh, S.A. (1998), "Confinement reinforcement design considerations for ductile hsc columns", J. Struct. Eng., 124(9), 999-1010. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:9(999)
  7. Carrasquilio, R.L. and Nilson, A.H. (1981), "Properties of high strength concrete subject to short-term loads", ACI J. Proceedings, 78(3), 171-178.
  8. Chen, M.T. and Ho, J.C.M. (2014), "Concurrent flexural strength and ductility design of RC beams via strain-gradient-dependent concrete stress-strain curve", Struct. Des. Tall Special Build., DOI:10.1002/tal.1203
  9. Claeson, C. and Gylltoft, K. (1998), "Slender high-strength concrete columns subjected to eccentric loading", J. Struct. Eng., 124(3), 233-240. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:3(233)
  10. Clark, L.E., Gerstle, K.H. and Tulin, L.G. (1967), "Effect of strain gradient on the stress-strain curve of motar and concrete", ACI J., 64(9), 580-586.
  11. Debernardi, P.G. and Taliano, M. (2002), "On evaluation of rotation capacity for reinforced concrete beams", ACI Struct. J.l, 99(3), 360-368.
  12. European Committee for Standardization (2004), Eurocode 2: Design of Concrete Structures: Part 1-1: General rules and rules for buildings, UK, 225.
  13. Foster, S.J. and Attard, M.M. (1997), "Experimental tests on eccentrically loaded high strength concrete columns", ACI Struct. J., 94(3), 295-303.
  14. Hadi, M.N.S. and Widiarsa, I.B.R. (2012), "Axial and flexural performance of square rc columns wrapped with cfrp under eccentric loading", J. Compos.Constr., 16(6), 640-649. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000301
  15. Ho, J.C.M. (2012), "Experimental tests on high-strength concrete columns subjected to combined medium axial load and flexure", Adv. Struct. Eng., 15(8), 1359-1374. https://doi.org/10.1260/1369-4332.15.8.1359
  16. Ho, J.C.M. and Pam, H.J. (2002), "Flexural strength and ductility performance of high-strength reinforced concrete columns", Struct. Eng., 80(23), 26-34.
  17. Ho, J.C.M. and Pam, H.J. (2003), "Inelastic design of low-axially loaded high-strength reinforced concrete columns", Eng. Struct., 25(8), 1083-1096. https://doi.org/10.1016/S0141-0296(03)00050-6
  18. Ho, J.C.M. and Peng, J. (2011), "Strain gradient effects on flexural strength design of normal-strength concrete columns", Eng. Structures, 33(1), 18-31. https://doi.org/10.1016/j.engstruct.2010.09.014
  19. Ho, J.C.M. and Peng, J. (2013), "Improving design limits of strength and ductility of NSC beam by considering strain gradient effect", Struct. Eng. Mech., 47(2), 185-207. https://doi.org/10.12989/sem.2013.47.2.185
  20. Ho, J.C.M. and Peng, J. (2013), "Strain-gradient-dependent stress-strain curve for normal-strength concrete", Adv. Struct. Eng., 16(11), 1911-1930. https://doi.org/10.1260/1369-4332.16.11.1911
  21. Ho, J.C.M., Pam, H.J., Peng, J. and Wong, Y.L. (2011), "Maximum concrete stress developed in flexural RC members", Comput. Concr., 8(2), 207-227. https://doi.org/10.12989/cac.2011.8.2.207
  22. Hognestad, E. (1951), A study of combined bending and axial load in reinforced concrete members. Urbana: University of Illinois.
  23. Ibrahim, H.H. and MacGregor, J.G. (1996), "Flexural behavior of laterally reinforced high-strength concrete sections", ACI Struct. J., 93(6).
  24. Ibrahim, H.H. and MacGregor, J.G. (1997), "Modification of the aci rectangular stress block for highstrength concrete", ACI Struct. J., 94(1).
  25. Karsan, I.D. and Jirsa, J.O. (1970), "Behavior of concrete under varying strain gradients", J. Struct. Div., 90(8), 1675-1696.
  26. Kim, S.J. (2007). Behavior of high-strength concrete columns. (Doctor of Philosophy), North Carolina State University, Raleigh, North Carolina.
  27. Ko, M.Y., Kim, S.W. and Kim, J.K. (2001), "Experimental study on the plastic rotation capacity of reinforced high strength concrete beams", Mater. Struct., 34(5), 302-311. https://doi.org/10.1007/BF02482210
  28. Lam, S.S.E., Wu, B., Wong, Y.L., Wang, Z.Y., Liu, Z.Q. and Li, C.S. (2003), "Drift capacity of rectangular reinforced concrete columns with low lateral confinement and high-axial load", J. Struct. Eng., 129(6), 733-742. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:6(733)
  29. Lee, J.H. and Son, H.S. (2000), "Failure and strength of high-strength concrete columns subjected to eccentric loads", ACI Struct. J., 97(1), 75-85.
  30. Li, C. (2013), "Size-dependent thermal behaviors of axially traveling nanobeams based on a strain gradient theory", Struct. Eng. Mech., 48(3), 415-434. https://doi.org/10.12989/sem.2013.48.3.415
  31. Lloyd, N.A. and Rangan, B.V. (1996), "Studies on high-strength concrete columns under eccentric compression", ACI Struct. J., 93(6), 631-638.
  32. Marefat, M.S., Khanmohammadi, M., Bahrani, M.K. and Goli, A. (2005), "Cyclic load testing and numerical modeling of concrete columns with substandard seismic details", Comput. Concr., 2(5), 367-380. https://doi.org/10.12989/cac.2005.2.5.367
  33. Mattock, A.H., Kriz, L.B. and Hognestad, E. (1961), "Rectangular concrete stress distribution in ultimate strength design", ACI Journal Proceedings, 57(2).
  34. Mo, Y.L. and Wang, S.J. (2000), "Seismic behavior of rc columns with various tie configurations", J. Struct. Eng., 126(10), 1122-1130. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:10(1122)
  35. Nemecek, J., Padevet, P., Patzak, B. and Bittnar, Z. (2005), "Effect of transversal reinforcement in normal and high strength concrete columns", Mater. Struct., 38(7), 665-671. https://doi.org/10.1617/14170
  36. Pam, H.J. and Ho, J.C.M. (2001), "Flexural strength enhancement of confined reinforced concrete columns", Proceedings of the Institution of Civil Engineers, 146(4), 363-370.
  37. Park, R. (2001), "Improving the resistance of structures to earthquakes", Bull. New Zeal. National Soc. Earthq. Eng., 34(1), 1-39.
  38. Park, R., Priestley, M. and Gill, W.D. (1982), "Ductility of square-confined concrete columns", J. Struct. Div., 108(4), 929-950.
  39. Peng, J., Ho, J.C.M., Pam, H.J. and Wong, Y.L. (2012), "Equivalent stress block for normal-strength concrete incorporating strain gradient effect", Mag. Concrete Res., 64(1), 1-19. https://doi.org/10.1680/macr.2012.64.1.1
  40. Rashid, M.A. and Mansur, M.A. (2005), "Reinforced high-strength concrete beams in flexure", ACI Struct. J., 102(3), 462-471.
  41. Saatcioglu, M. and Ozcebe, G. (1989), "Response of reinforced concrete columns to simulated seismic loading", ACI Struct. J., 86(1), 3-12.
  42. Sargin, M., Ghosh, S. and Handa, V. (1971), "Effects of lateral reinforcement upon the strength and deformation properties of concrete", Mag. Concrete Res., 23(75 & 76), 99-110. https://doi.org/10.1680/macr.1971.23.76.99
  43. Scott, B.D., Park, R. and Priestley, M.J.N. (1982), "Stress-strain behaviour of concrete confined by overlapping hoops at low and high strain rates", ACI J., 79(1), 13-27.
  44. Sheikh, S.A. and Khoury, S.S. (1993), "Confined concrete columns with stubs", ACI Struct. J., 90, 414-414.
  45. Sheikh, S.A., Shah, D.V. and Khoury, S.S. (1994), "Confinement of high-strength concrete columns", ACI Struct. J., 91(1), 100-111.
  46. Sheikh, S.A. and Yeh, C.C. (1986), "Flexural behavior of confined concrete columns", ACI J., 83(3), 389-404.
  47. Sheikh, S.A. and Yeh, C.C. (1990), "Tied concrete columns under axial load and flexure", J. Struct. Eng., 116(10), 2780-2800. https://doi.org/10.1061/(ASCE)0733-9445(1990)116:10(2780)
  48. Sheikh, S.A. and Yeh, C.C. (1992), "Analytical moment-curvature relations for tied concrete columns", J. Struct. Eng., 118(2), 529-544. https://doi.org/10.1061/(ASCE)0733-9445(1992)118:2(529)
  49. Standards New Zealand, NZS 3101 (2006), Concrete Structures Standard, Part 1: The Design of Concrete Structures, Wellington, New Zealand.
  50. Sturman, G.M., Shah, S.P. and Winter, G. (1965), "Effects of flexural strain gradients on microcracking and stress-strain behavior of concrete", ACI J., 62(7), 805-822.
  51. Tan, T. and Nguyen, N. (2004), "Determination of stress-strain curves of concrete from flexure tests", Mag. Concrete Res., 56(4), 243-250. https://doi.org/10.1680/macr.2004.56.4.243
  52. Tan, T.H. and Nguyen, N.B. (2005), "Flexural behavior of confined high-strength concrete columns", ACI Struct. J., 102(2).
  53. Tao, Z. and Yu, Q. (2008), "Behaviour of cfrp-strengthened slender square rc columns", Mag. Concrete Res., 60(7), 523-533. https://doi.org/10.1680/macr.2008.60.7.523
  54. Watson, S. and Park, R. (1994), "Simulated seismic load tests on reinforced concrete columns", J. Struct. Eng., 120(6), 1825-1849. https://doi.org/10.1061/(ASCE)0733-9445(1994)120:6(1825)
  55. Wong, H.H.C. and Kwan, A.K.H. (2008), "Packing density of cementitious materials: Part 1 - measurement using a wet packing method", Mater. Struct., 41(6), 689-701. https://doi.org/10.1617/s11527-007-9274-5
  56. Woods, J.M., Kiousis, P.D., Ehsani, M.R., Saadatmanesh, H. and Fritz, W. (2007), "Bending ductility of rectangular high strength concrete columns", Eng. Struct., 29(8), 1783-1790. https://doi.org/10.1016/j.engstruct.2006.09.024
  57. Xiao, Y. and Martirossyan, A. (1998), "Seismic performance of high-strength concrete columns", J. Struct. Eng., 124(3), 241-251. https://doi.org/10.1061/(ASCE)0733-9445(1998)124:3(241)

Cited by

  1. Effect of confinement on flexural ductility design of concrete beams vol.20, pp.2, 2015, https://doi.org/10.12989/cac.2017.20.2.129
  2. Tensile behaviour of ultra-high-performance steel fiber reinforced concrete vol.48, pp.11, 2015, https://doi.org/10.1139/cjce-2019-0592